# changelog

author: Hewlett Packard Enterprise Development LP 7.6.1
changelog:
  - Updated the following components
     PHP to version php-5.6.27
     OpenSSL to version openssl-1.0.2k
     Apache to version httpd-2.4.25
   - SMH is been improvised with respect to security vulnerabilities
   Upgrade Requirement: Recommended – HPE recommends users update to this version at their earliest convenience.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.22.0
changelog:
  -      Fixed an issue where certain SAS and SATA SSD drives greater than 2 TB will not work in HPE Synergy D3940 Storage Module when attached to HPE Synergy 12Gb SAS Connection Module running firmware version 1.0.20.0


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.08
changelog:
  -      Intermittent memory errors might cause the controller to stop responding. (POST Lockup 0x13)
      
        * System might stop responding if a parity error is found during surface scan of a RAID6 volume. (POST Lockup 0x13)
      
        * In rare cases, the controller might stop responding while running IO without displaying a lockup code.
      
        * Non-Maskable Interrupt (NMI) might occur on systems with a Windows OS and HPE Gen9 Smart Array or Smart HBA adapters and performing continuous reboot testing.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.10
changelog:
  -      If and unexpected power outage occurred, the system might stop operating during Power-On Self Test
      
        * Controller could stop responding when Smart Cache is performing a read-ahead after finishing a read-fill for a pending flush operation


author: Linux Storage Driver Team <esc.storagedev@microsemi.com> 3.4.20-110
changelog:
  * Fri Apr 21 2017 Linux Storage Driver Team <esc.storagedev@microsemi.com> 3.4.20-100
   - Correct multipath failover operation that could fail to work under high
     IO conditions.


author: Linux Storage Driver Team <esc.storagedev@microsemi.com> 3.4.18-100
changelog:
  - 2017 driver update
   - hpsa: remove coalescing settings for ioaccel2 which actually degraded
     performance.


author: Linux Storage Driver Team <esc.storagedev@microsemi.com> 3.4.18-105
changelog:
  - 2017 driver update
   - hpsa: do not send resets to enclosures
   - hpsa: correct queue depth setting for externals external queue depth
     setting was in the wrong place.  The queue depth defaulted to 1012 which
     seems to be too high for RBOD devices. This was having an impact on
     multipath failover testing. Redhat BZ: 1404073 ESDSD-1171
   - hpsa: correct offline detection


author: HP Linux Development <Linux_SWdeliverables@external.groups.hp.com> 10.5.0
changelog:
  - FIXES
  - Cmahostd does not ignore nfs4 mount points.
  - cmahostd triggers NFS auto-mounting and resulted in performance problem.
  - Files in directories under /var/spool/compaq/hpasm/registry/ have SGID bit set removed.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.20_05-16-2016
changelog:
  -     Added support for Intel Xeon E7-4800 v4 and E7-8800 v4 series processors.
      
      Added support for 128GB Load Reduced DIMMs (LRDIMM).
      
      Added a new System Utilities BIOS/Platform Configuration (RBSU) PCIe I/O
      Allocation option that allows the user to select how PCIe resources are
      assigned. This option can be used to address an issue where a server
      configured with a large number PCIe option cards that request legacy I/O
      space, such as Graphics Adapters, will display and log to the Integrated
      Management Log (IML) a "276-IMPORTANT: Option Card Configuration Error"
      message indicating that one or more PCIe devices may not have been assigned
      its requested I/O resources and attempt to boot.
      
      Updated the UEFI Secure Boot revocations list (DBX) with the latest copy from
      Microsoft.
      
      Updated to the latest support modules for Intel Trusted eXecution Technology
      (TXT) including the Intel Authenticated Code Module (ACM) and Intel Secure
      Initialization (SINIT) module.
      
      Updated the HP RESTful API HPE BIOS Attribute Registry resources to match the
      latest BIOS/Platform Configuration options.
      
      Updated the language translations (non-English modes) for System Utilities.
      
      Updated the UEFI Secure Boot Key Database revocations list (DBX) with the
      latest version from Microsoft. This includes the latest list of revoked
      certificates.
      
      Increased the default timeout value of the iSCSI UEFI Software Initiator boot
      to 20 seconds. This may help resolve issues of intermittent connection drop
      during an iSCSI boot.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.20_05-16-2016
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the System Utilities BIOS/Platform Configuration
      (RBSU) USB Boot Options setting may not properly allow the server to boot from
      the internal SD card before a USB key when SD is higher in the priority list.
      This issue only affects servers configured in Legacy Boot Mode.
      
      Addressed an issue where the ambient temperature reported by the system during
      server boot may report incorrectly. This issue also requires an iLO firmware
      version update to a revision later than 2.4x which will be released later this
      year. This issue has no impact on the thermal operation of the server and is
      simply an issue with the temperature displayed during boot. While updating to
      this revision of the BIOS will not address this issue unless the iLO FW
      revision is later than 2.4x, there are no issues caused by updating the BIOS
      without updating iLO FW.
      
      Addressed an issue where the UEFI or Legacy Option ROM for a PCIe adapter may
      not be properly executed when installed in certain slots. This could cause
      such issues as an inability to boot using the PCIe adapter. This issue was
      seen with a Brocade network adapter but could be seen with other adapters.
      
      Addressed an issue where the server health LED may remain set in a degraded or
      failed state after an error event was resolved during server operation.
      Previously, a server reset may have been needed to clear the health LED event.
      
      Addressed an extremely rare issue where the server may become unresponsive
      during boot when performing reboot testing. When this issue occurs, the system
      will report an Illegal Opcode Exception (Red Screen) in the pre-boot error
      handler.
      
      Addressed an issue where the System Utilities BIOS/Platform Configuration
      (RBSU) option for Embedded UEFI Shell Auto Startup Script Network Location
      does not accept an NSH file name containing upper case characters.
      
      Addressed an issue where the UEFI iSCSI Software Initiator boot options may
      become invalid if the DHCP server provides a new IP Address to a previously
      configured iSCSI boot option.
      
      Addressed an issue where the system may become unresponsive during boot when
      configured with a HPE Dual microSD device when one of the microSD devices is
      failed or missing.
      
      Addressed an issue where the server may assign incorrect ACPI NUMA proximity
      allocations for servers configured with two or more processors and with memory
      only attached to a single processor socket potentially leading to non-optimal
      performance. This issue does not impact servers with memory configured on
      multiple processors.
      
      Addressed an issue where the Automatic Server Recovery (ASR) setting may not
      be configured properly through the HP RESTful API.
      
      Addressed an issue where the internal SD card would remain active after the
      user has disabled the SD slot from System Utilities BIOS/Platform
      Configuration (RBSU) option. This issue only affects systems configured in
      Legacy Boot Mode.
      
      Addressed an issue where the server may become unresponsive when using the
      PING command from the Embedded UEFI Shell.
      
      Addressed an issue where the UEFI iSCSI Software Initiator boot options may
      become invalid if the DHCP server provides a new IP Address to a previously
      configured iSCSI boot option.
      
      Addressed an issue where the system may fail to boot from existing UEFI iSCSI
      Software Initiator boot options if the user changed the iSCSI Target IP
      address.
      
      Addressed an issue where the system may fail to boot from UEFI iSCSI Software
      Initiator boot options that has iSCSI Initiator or Target configured using
      static IPv6 addresses.
      
      Addressed an issue where the UEFI iSCSI Software Initiator boot option IPv6
      address cannot be configured using the HP RESTful API.
      
      Addressed an issue that may result in losing the existing UEFI iSCSI Software
      Initiator boot options if any of the connection parameters (LUN, Remote Port,
      IP address, login credentials) change.
      
      Addressed an issue in reporting the incorrect PCIe slot number in the error
      messages of failed iSCSI boot attempts.
      
      Addressed an issue of iSCSI boot configuration options not being available
      from the HP RESTful API when there are no network adapters in the system.
      
      Addressed an extremely rare issue where the server may become unresponsive due
      to a Non Maskable Interrupt (NMI) when performing a shutdown or startup from
      an Operating System.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.22_07-21-2016
changelog:
  -     *Important Notes:**
      
      HPE requires that any server using the 2.20 version of the System ROM be
      updated to version 2.22 or later due to the issue addressed by version 2.22 of
      the System ROM.  Note that the version 2.20 05/16/2016 System ROM has been
      removed from the HPE Support Site.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where systems using the version 2.20 05/16/2016 System ROM
      may experience Unexpected Machine Check Exceptions or Uncorrectable Memory
      errors (as indicated in the Integrated Management Log (IML)).  It is
      recommended that users who are experiencing this issue update to this revision
      of the System ROM or later before replacing any components.  Note that the
      version 2.20 05/16/2016 of the System ROM was removed from the HPE Support
      site due to this issue.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.30_09-12-2016
changelog:
  -     Updated to the latest support modules for Intel Trusted eXecution Technology
      (TXT) including the Intel Authenticated Code Module (ACM) and Intel Secure
      Initialization (SINIT) module.
      
      Updated the UEFI Secure Boot Key Database revocations list (DBX) with the
      latest version from Microsoft. This includes the latest list of revoked
      certificates.
      
      Updated the HP RESTful API HPE BIOS Attribute Registry resources to match the
      latest BIOS/Platform Configuration options.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.30_09-12-2016
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed a rare issue where fatal system errors may not be logged to the
      Integrated Management Log (IML) when an error occurs on any processor other
      than Processor 1.
      
      Addressed an extremely rare issue where the system may receive a Red Screen
      error and become unresponsive during boot. This issue would not be seen if the
      ROM Based Setup Utility (RBSU) Option for Dynamic Power Calibration is set to
      Disabled (the default for this option is Auto which could result in this
      issue).
      
      Addressed an issue where the system would become unresponsive during boot and
      display a NMI error when configured with an optional PCI Express device
      supporting older versions of the PCI Express specification.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.40_02-17-2017
changelog:
  -     *Important Notes:**
      
      None  
      
      **Firmware Dependencies:**
      
      None  
      
      **Problems Fixed:**
      
      Addressed an issue where the system may become unresponsive during system boot
      when a third party USB 3.0 XHCI adapter card is installed in the server.
      
      Addressed an issue where the system may properly indicate that a DIMM has
      experienced a high rate of corrected memory errors in the Integrated
      Management Log (IML), but the DIMM's status may incorrectly be reported in the
      iLO GUI as healthy. The iLO GUI will now report the DIMM's status as degraded.
      
      Addressed an issue where the system may become unresponsive during system boot
      when a USB-based UPS is attached to the server USB ports. This issue only
      impacted a system when configured for legacy boot mode.
      
      Addressed an issue where the system may not properly report and log errors to
      the Integrated Management Log (IML) detected on the optional HPE Dual SD Card
      option. This issue only impacted logging when the system performed a warm
      reset.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.40_02-17-2017-2.1
changelog:
  -     *Important Notes:**
      
      Ver. 2.40_02-17-2017 (B)  contains updates to the component packaging and is
      functionally equivalent to ver. 2.40_02-17-2017.  It is not necessary to
      upgrade with Revision B if a previous component Revision was used to upgrade
      the system ROM to version 2.40_02-17-2017.  
      
      **Firmware Dependencies:**
      
      None  
      
      **Problems Fixed:**
      
      Addressed an issue where the system may become unresponsive during system boot
      when a third party USB 3.0 XHCI adapter card is installed in the server.
      
      Addressed an issue where the system may properly indicate that a DIMM has
      experienced a high rate of corrected memory errors in the Integrated
      Management Log (IML), but the DIMM's status may incorrectly be reported in the
      iLO GUI as healthy. The iLO GUI will now report the DIMM's status as degraded.
      
      Addressed an issue where the system may become unresponsive during system boot
      when a USB-based UPS is attached to the server USB ports. This issue only
      impacted a system when configured for legacy boot mode.
      
      Addressed an issue where the system may not properly report and log errors to
      the Integrated Management Log (IML) detected on the optional HPE Dual SD Card
      option. This issue only impacted logging when the system performed a warm
      reset.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.60
changelog:
  -     Onboard Administrator 4.60 provides support for the following enhancements:
      
        * **Hardware Additions**
          * None.
        *  **Features Additions and Changes**
          * **General**
            * GUI, CLI, Smart components, help files, URLs, Product Names rebranded to align with HPE branding guidelines.
            * Enhanced information reporting of Gen9 servers booted in UEFI mode.
            * Support the configuration of SNMP trap agent address when non-default VLAN is enabled on OA.
            * Enhanced syslog to show the flooding information when VLAN configured nodes flood the management network.
          * **Remote Support**
            * Modified to connect to the HPE remote support URL.
          * **EFM**
            * Enhanced error handling mechanism in EFM for servers in UEFI boot mode.
            * Enhanced EFM to display detailed name for smart array controllers .
            * EFM enhanced to identify more devices in the EFM report.
            * Enhanced the status reporting of EFM operations to align with HPSUM return codes


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.70
changelog:
  -     *General**
      
        * Addressed an issue where OA "update iLO all" command fails in an enclosure with maximum Blades.
        * Addressed an issue where a Warning Alert  was wrongly sent when a fan is reseated in an enclosure
        * Addressed an issue where the port mapping information for 560M Izzy adapter Mezz controller was not displayed correctly.
        * Addressed an issue where Remote Syslog logging would fail when OA failover happened in an IPv6 only environment.
        * Enhanced OA to bring the server from a power throttled state back to normal power state upon an OA reboot to circumvent an unwarranted emergency brake.
        * Fixed an issue where the Active and Standby OAs can have the same IP address in some rare situations.
        * Resolved an issue where a Gen9 server's host name gets cleared when the blade is rebooted.
        * Addressed an issue where server blade Power ON will be delayed in enclosures with OA Firmware Version 4.60 and managed by HPE OneView, when the OA module is reset until OneView refreshes the servers.
      
      **Security**
      
      The following security vulnerabilities were fixed:
      
        * CVE-2016-5387- Addressed a vulnerability which might allow remote attackers to redirect an application's outbound HTTP traffic to an arbitrary proxy server via a crafted Proxy header in an HTTP request.
        * CVE-2016-2183- Addressed a vulnerability against TLS ciphers with 64bit block size in which makes it easier for remote attackers to obtain cleartext data via an attack against a long-duration encrypted session
        * CVE-2016-6515 - Addressed a vulnerability in OpenSSH which did not limit password lengths for password authentication, which allows remote attackers to cause a denial of service via a long string.
        * CVE-2015-8215 - Addressed a vulnerability IPv6 stack which does not validate attempted changes to the MTU value, which allows context-dependent attackers to cause a denial of service.
        * Addressed issue where in Onboard Administrator was vulnerable to Buffer overflow.
        * Added the HSTS[HTTP strict transport security] support  in OA.
        * Addressed a memory corruption vulnerability in the post-authentication sshd process.
      
      **Issues and workarounds**
      
      **Browsers**
      
        * OA GUI is not accessible in Chrome versions 43.0.2357.10 to 44.0.2383.The issue was caused by a "regression" in Chrome (or WebKit). Customers should use an alternative browser like Firefox or Internet Explorer or try a different version of Chrome.
        * SSO-to-iLO connection from the OA using an iLO host name fails with Microsoft Internet Explorer11 on Windows 8.On a Windows 8 system with Internet Explorer 10 or Internet Explorer 11, if the OA web GUI session is loaded using a host name instead of an IP address, an attempt to open an iLO window using SSO from the OA web GUI might result in the iLO page loading in the OA web GUI window instead of the intended new window. This issue was determined to be a bug in Internet Explorer and is expected to be fixed in a future release or update for Internet Explorer. To work around this issue, either use an IP address to load the OA Web GUI, or turn off Protected Mode for the appropriate zone in Internet Explorer's settings. This issue occurs only on Internet Explorer browsers.
      
      **FIPS**
      
      Certificates smaller than 2048 bits in size are not compliant with FIPS
      requirements as enforced by the OA firmware starting with OA 4.20. When the OA
      running OA firmware version 4.40 or greater is operating in FIPS Mode ON/DEBUG
      and is configured with a 1024-bit LDAP certificate that was installed when
      running a previous version of OA firmware, FIPS Mode ON/DEBUG is considered to
      be operating in a degraded state due to the presence of the non-compliant
      certificate. While operating in this FIPS-Degraded Mode operational state,
      attempts to set FIPS Mode OFF from the OA GUI Network Access>FIPS tab will
      fail and show the error message The selected FIPS mode is already enabled.
      When the non-compliant certificate is removed, the FIPS-Degraded operational
      status is cleared, FIPS Mode can then be successfully set to OFF from the GUI
      interface. Note that the OA CLI command SET FIPS MODE OFF can be successfully
      used to set FIPS Mode OFF even with non-compliant 1024-bit LDAP certificates
      installed in the OA.
      
      **IRC**
      
      Unable to open .net IRC console for Gen10 Blades, Gen9 Blades also have the
      same issue. The Java applet and Webstart however, loads but the virtual media
      mounting fails. The work around is to launch the IRC through IRC Application
      (HP Lights-Out Stand Alone Remote Console) which is installed on terminal
      client.
      
      **EFM **
      
      To use EFM on Gen 10 Blades, please select options/filters "_Make Bootable ISO
      file" and _"_Enclosure Firmware Management"_ while creating custom SPP ISO on
      HPSUM 8.0.0. Please refer to HPSUM 8.0.0 User guide for further details.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.50
changelog:
  -     The latest list of enhancements can be found in the HPE Virtual Connect
      Release Notes that can be found in the following URL**:
      **<http://www.hpe.com/info/vc/manuals>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.50
changelog:
  -     Note for ESXi users: If you are booted from the Embedded SD Card, it is
      strongly  
      Recommended that you reboot the server immediately after updating to iLO 4
      v2.50.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.50
changelog:
  -     This version adds support for the following features and enhancements:
      
        * Implemented Garbage collection on the RESTful API allowing for automatic recovery in the case of bad or missing data.
        * Updates to the enclosure connection status (CPQSTSYS cpqSsBoxConnectionStatus) now correctly report when an enclosure is disconnected or reconnected, and sends trap cpqSsConnectionStatusChange where appropriate.
        * This version adds protection to the lifespan of the embedded 4GB non-volatile storage (NAND) by implementing a daily write count limit that is well above the normal daily activity.  This ensures a runaway process will not inadvertently write to the NAND excessively leading to eventual failure.
        * Changed the default SSL certificate signing to SHA-256.
        * Added support for IP addresses in the SubjectAltName field of the iLO SSL certificate.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.50
changelog:
  -     The following issues are resolved in this version:
      
        * Dynamic Power Capping still works when set to disabled.
        * Server may shut down after repeated insertion and removal of hot-plug power input modules for RPS backplanes. 
        * Repeated LDAP tests cause iLO LDAP User Authentication to fail.
        * The reporting of location discovery services data via the RESTful API on ML/DL servers failed even with iLO Advanced license installed.
        * Rare memory leak that could lead to slow or failed iLO interfaces due to unverified data returns from unregistered providers.
        * Corrected the link on the direct connect registration page to point to [www.hpe.com/support/hpesc](http://www.hpe.com/support/hpesc) instead of [www.hpe.com/services/hpesc](http://www.hpe.com/services/hpesc).
        * OA communication issue after OneView SPP update.
        * Status of pure Fibre Channel cards show up as Unknown in Network Tab of iLO System Information.
        * External Rest Providers removed after upgrading BIOS, booting, and then resetting iLO.
        * Rarely a GET to the SNMP MIB will fail.
        * Rarely updates using HPSUT fail.
        * iLOs won't join Federation group or respond to SSDP requests if DHCPv4 is configured but an IP address is not obtained at iLO boot time.
        * Prev/Next links and list behavior of iLO federation are not consistent.
        * Security fixes/enhancements: 
          * Improved AlertMail message body encoding.
          * CBC Mode ciphers disabled in FIPS/AES Modes (both Webserver and SSH).
          * RC4 has been removed from the default cipher list.
          * 3DES and SHA-1 are disabled in FIPS mode.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.53
changelog:
  -     This version adds support for the following features and enhancements:  
         iLO Amplifier Pack - Advanced Server Firmware/Driver and License
      Management Solution  
         OpenLDAP  
         OpenSSL 1.0.1u FIPS  
         PSRT 301  
         CSRs no longer include the iLO IP address by default. To include the iLO
      IP address in the CSR, enable  
          the include iLO IP Address(es) option in the iLO web interface.  
         Added an iLO RESTful API option to include the iLO IP address in SSL
      certificate CSRs.  
         AlertMail formatting improvements.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.53
changelog:
  -     The following issues are resolved in this version:  
         Fixed an issue that led to POST Error: 333-iLO RESTful API Error - Unable
      to communicate with the iLO firmware when an SD card is was installed.  
         Fix handling of logical drive indexing, found in cases where logical
      drives are not contiguous.  
         Power loss occurs when hot-plugging RPS backplane during runtime.  
         High fan noise occurs during ML110 Gen9 server system startup.  
         IPMI Drive fault is incorrectly mapped to "In Failed Array" on drive
      sensors.  
         Target node iLO is unavailable when an HPE OneView server profile is
      applied.  
         The iLO RESTful API Software Inventory is incomplete when compared to the
      iLO web interface.  
         The iLO RESTful API does not return complete version strings for all
      software components.  
         Unable to use IPMI to "Set Serial Number" and "Set Product ID".  
         Fan failure and server shutdown occur on SL230s Gen8 servers.  
         Reverse Address Translate returns bad values when called with hponcfg.  
         The iLO RESTful API does not return the exact PCI device location for PCIe
      components.  
         An incorrect device type is reported for the embedded SATA controller.  
         Performing a NAND format may leave the REST provider registration in an
      unstable state.  
         Solid state drives are intermittently reported as hard disk drives.  
         Fixed SNMP configuration read failure issue due to wrong FQDN trap
      destination configuration.  
         Fixed an issue that could lead to distorted video after setting boot mode
      to UEFI via RIBCL.  
         False Self-Test error on USB port may be reported when an HPE ProLiant
      Gen8-Series server is powered Off (Advisory found at:
      http://h20565.www2.hpe.com/hpsc/doc/public/display?docId=emr_na-
      a00007681en_us)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.54
changelog:
  -     This version adds support for the following features and enhancements:
      
        * iLO Amplifier Pack - Advanced Server Firmware/Driver and License Management Solution
        * OpenLDAP
        * OpenSSL 1.0.1u FIPS
        * PSRT 301
        * CSRs no longer include the iLO IP address by default. To include the iLO IP address in the CSR, enable the include iLO IP Address(es) option in the iLO web interface.
        * Added an iLO RESTful API option to include the iLO IP address in SSL certificate CSRs.
        * AlertMail formatting improvements.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.54
changelog:
  -     The following issues are resolved in this version:
      
        * Resolved an issue where in some cases iLO configuration data could be reset to default values after an iLO firmware upgrade (only affects Gen8 servers).
        * Improved the mechanism to reset communication to the non-volatile storage (NAND) upon a warm reboot of the server (to reset an inaccessible NAND)
        * NOTE: If the NAND is inaccessible when upgrading to iLO 4 2.54 firmware, an AC power pull may be necessary to reset an inaccessible NAND.
      
      The following issues are resolved in version 2.53 (replaced by 2.54):
      
        * Fixed an issue that led to POST Error: 333-iLO RESTful API Error - Unable to communicate with the iLO firmware when an SD card is was installed.
        * Fix handling of logical drive indexing, found in cases where logical drives are not contiguous.
        * Power loss occurs when hot-plugging RPS backplane during runtime.
        * High fan noise occurs during ML110 Gen9 server system startup.
        * IPMI Drive fault is incorrectly mapped to "In Failed Array" on drive sensors.
        * Target node iLO is unavailable when an HPE OneView server profile is applied.
        * The iLO RESTful API Software Inventory is incomplete when compared to the iLO web interface.
        * The iLO RESTful API does not return complete version strings for all software components.
        * Unable to use IPMI to "Set Serial Number" and "Set Product ID".
        * Fan failure and server shutdown occur on SL230s Gen8 servers.
        * Reverse Address Translate returns bad values when called with hponcfg.
        * The iLO RESTful API does not return the exact PCI device location for PCIe components.
        * An incorrect device type is reported for the embedded SATA controller.
        * Performing a NAND format may leave the REST provider registration in an unstable state.
        * Solid state drives are intermittently reported as hard disk drives.   
        * Fixed SNMP configuration read failure issue due to wrong FQDN trap destination configuration.  
        * Fixed an issue that could lead to distorted video after setting boot mode to UEFI via RIBCL.
        * False Self-Test error on USB port may be reported when an HPE ProLiant Gen8-Series server is powered Off (Advisory found at: http://h20565.www2.hpe.com/hpsc/doc/public/display?docId=emr_na-a00007681en_us)
        * Improved error handling of option card AHS data that could result in excessive descriptor growth resulting in large AHS data files.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.55
changelog:
  -     The following issues are resolved in this version:
      
        * Masked out errant failures due to charging of storage battery.
        * Implemented cell voltage separation pre-failure warning for storage battery.
        * iLO RESTful API output might display incorrect power supply information.
        * iLO Federation group authentication errors might occur if you repeatedly add and remove groups during a query.
        * An iLO RESTful API event subscription might be lost when DELETE and CREATE subscriptions occur at the same time that the transmitter waits to retry an action.
        * During CAC smartcard authentication, the iLO RESTful API returns a session URI that incorrectly contains uppercase letters.
        * In certain conditions, the Rest server becomes unavailable during a GET of the IELs.
        * The iLO web interface language pack redirects to English.
        * The iLO RESTful API output text represents upper threshold values as lower thresholds.
        * The Linux openipmi driver does not poll the receive message queue if KCS host irq not enabled.
        * The iLO RESTful API EthernetInterfaces link should be under the system/1 root resource, and not in the OEM section.
        * SNMPv3 Engine Boot is not getting incremented on iLO reset.
        * IPMI FRU read returns incorrect completion code for response too long.
        * IPMI Get PEF Capabilities returns the number of valid table entries instead of the total number of table entries.  
        * IPMI Set Boot Options for one time change for boot mode UEFI/Legacy fixed.  
        * iLO restserver suspends when patching bad payload to external provider array.
        * iLO REST API returned 500 internal error for a GET of systems/1/ leading to failed One View Profile Apply.
        * iLO RESfulT API events are sending incorrect "Host" header when using IPv6.
        * iLO time becomes Unset after update from 2.50 or prior to 2.54.


