# changelog

author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 15.10.07.00
changelog:
  -     *Problems Fixed in version 15.10.07.00:**
      
        * Resolves POST error 'MPT BIOS Fault 13h'. If this error occurs, the system will not boot from any boot device attached to an HP H2xx Host Bus Adapter (HBA) and will be unable to access data on drives attached to the HP H2xx HBA. The fault is triggered if the link between the HP H2xx HBA and the drives goes down during link tuning process. Updated firmware will no longer trigger this fault and the link is now allowed to re-establish itself. This issue is seen only with Solid State Drives (SSD).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 15.10.07.00-2.1
changelog:
  -      Customers who already installed firmware version 15.10.07.00 do not need to update to 15.10.07.00 (B).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 15.10.09.00
changelog:
  -     Firmware Version 15.10.09.00
      
        * Resolves a performance issue that was caused by a 90 msec timeout on all read/write operations when no Smart Carrier was present. This firmware reduces the read/write timeout to 2 msec.
      
        * Resolves a lockup issue during boot up on the HP ProLiant DL580 Gen8 Server when configured with the HP Host Bus Adapter H220 connected to SATA SSD or HDD drives.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 15.10.09.00-2.1
changelog:
  -     Firmware Version 15.10.09.00 (B)
      
        * Improved integration with HP Smart Update Manager
      
      Firmware Version 15.10.09.00
      
        * Resolves a performance issue that was caused by a 90 msec timeout on all read/write operations when no Smart Carrier was present. This firmware reduces the read/write timeout to 2 msec.
      
        * Resolves a lockup issue during boot up on the HP ProLiant DL580 Gen8 Server when configured with the HP Host Bus Adapter H220 connected to SATA SSD or HDD drives.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 15.10.10.00
changelog:
  -     *Problems Fixed in version 15.10.10.00:**
      
        * HPE ProLiant BL420c Gen8 server configured with HPE Dynamic Smart Array B320i RAID controllers, failed to boot and the system stopped responding during Power-On Self-Test (POST). In some instances, the message, "1783 Driver Array Controller Failure" was displayed. Please refer to HPE Customer Advisory [c05317927](http://h20566.www2.hpe.com/hpsc/doc/public/display?docId=c05317927) for details.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 15.10.10.00-2.1
changelog:
  -     Fixes an issue where the appropriate FW version for the Host Bus Adapter (HBA)
      Stockade (H2xx) driver will not install when using the Service Pack ProLiant
      (SPP)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.54
changelog:
  -     This version adds support for the following features and enhancements:
      
        * iLO Amplifier Pack - Advanced Server Firmware/Driver and License Management Solution
        * OpenLDAP
        * OpenSSL 1.0.1u FIPS
        * PSRT 301
        * CSRs no longer include the iLO IP address by default. To include the iLO IP address in the CSR, enable the include iLO IP Address(es) option in the iLO web interface.
        * Added an iLO RESTful API option to include the iLO IP address in SSL certificate CSRs.
        * AlertMail formatting improvements.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.54
changelog:
  -     The following issues are resolved in this version:
      
        * Resolved an issue where in some cases iLO configuration data could be reset to default values after an iLO firmware upgrade (only affects Gen8 servers).
        * Improved the mechanism to reset communication to the non-volatile storage (NAND) upon a warm reboot of the server (to reset an inaccessible NAND)
        * NOTE: If the NAND is inaccessible when upgrading to iLO 4 2.54 firmware, an AC power pull may be necessary to reset an inaccessible NAND.
      
      The following issues are resolved in version 2.53 (replaced by 2.54):
      
        * Fixed an issue that led to POST Error: 333-iLO RESTful API Error - Unable to communicate with the iLO firmware when an SD card is was installed.
        * Fix handling of logical drive indexing, found in cases where logical drives are not contiguous.
        * Power loss occurs when hot-plugging RPS backplane during runtime.
        * High fan noise occurs during ML110 Gen9 server system startup.
        * IPMI Drive fault is incorrectly mapped to "In Failed Array" on drive sensors.
        * Target node iLO is unavailable when an HPE OneView server profile is applied.
        * The iLO RESTful API Software Inventory is incomplete when compared to the iLO web interface.
        * The iLO RESTful API does not return complete version strings for all software components.
        * Unable to use IPMI to "Set Serial Number" and "Set Product ID".
        * Fan failure and server shutdown occur on SL230s Gen8 servers.
        * Reverse Address Translate returns bad values when called with hponcfg.
        * The iLO RESTful API does not return the exact PCI device location for PCIe components.
        * An incorrect device type is reported for the embedded SATA controller.
        * Performing a NAND format may leave the REST provider registration in an unstable state.
        * Solid state drives are intermittently reported as hard disk drives.   
        * Fixed SNMP configuration read failure issue due to wrong FQDN trap destination configuration.  
        * Fixed an issue that could lead to distorted video after setting boot mode to UEFI via RIBCL.
        * False Self-Test error on USB port may be reported when an HPE ProLiant Gen8-Series server is powered Off (Advisory found at: http://h20565.www2.hpe.com/hpsc/doc/public/display?docId=emr_na-a00007681en_us)
        * Improved error handling of option card AHS data that could result in excessive descriptor growth resulting in large AHS data files.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.55
changelog:
  -     This version adds support for the following features and enhancements:
      
        * The Self-signed SSL certificate can now be regenerated.
        * New iLO RESTful API command to allow an auxiliary power cycle of the server on the next host power down.
        * Added THERM_TRIP events, OS_STOP_SHUTDOWN, OS_NMI, ACPI, PCI-E Bus Error and CPU error logs to the SEL. 
        * Added OEM type SEL event with IML info on critical events.
        * Improved reliability of Embedded Media attach and diagnostics.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.55
changelog:
  -     The following issues are resolved in this version:
      
        * Masked out errant failures due to charging of storage battery.
        * Implemented cell voltage separation pre-failure warning for storage battery.
        * iLO RESTful API output might display incorrect power supply information.
        * iLO Federation group authentication errors might occur if you repeatedly add and remove groups during a query.
        * An iLO RESTful API event subscription might be lost when DELETE and CREATE subscriptions occur at the same time that the transmitter waits to retry an action.
        * During CAC smartcard authentication, the iLO RESTful API returns a session URI that incorrectly contains uppercase letters.
        * In certain conditions, the Rest server becomes unavailable during a GET of the IELs.
        * The iLO web interface language pack redirects to English.
        * The iLO RESTful API output text represents upper threshold values as lower thresholds.
        * The Linux openipmi driver does not poll the receive message queue if KCS host irq not enabled.
        * The iLO RESTful API EthernetInterfaces link should be under the system/1 root resource, and not in the OEM section.
        * SNMPv3 Engine Boot is not getting incremented on iLO reset.
        * IPMI FRU read returns incorrect completion code for response too long.
        * IPMI Get PEF Capabilities returns the number of valid table entries instead of the total number of table entries.  
        * IPMI Set Boot Options for one time change for boot mode UEFI/Legacy fixed.  
        * iLO restserver suspends when patching bad payload to external provider array.
        * iLO REST API returned 500 internal error for a GET of systems/1/ leading to failed One View Profile Apply.
        * iLO RESfulT API events are sending incorrect "Host" header when using IPv6.
        * iLO time becomes Unset after update from 2.50 or prior to 2.54.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.60
changelog:
  -     Install this update to take advantage of significant improvements to the write
      algorithm for the embedded 4 GB non-volatile flash memory (also known as the
      NAND). These improvements increase the NAND lifespan.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.60
changelog:
  -     This version adds support for the following features and enhancements:
      
        * IPMI/DCMI over LAN access is disabled by default on new servers with iLO 4 2.60.
        * IPMI/DCMI over LAN access is disabled after you reset iLO 4 2.60 to the factory default settings. 
        * Each time iLO starts, it backs up the iLO configuration to the nonvolatile flash memory (NAND). If the SRAM is erased, the configuration is automatically restored.
        * Improved Active Health System logging efficiency to prolong the NAND lifespan. 
        * Added iLO health status to the Overview page. If the status is Degraded, this value is also displayed on the Login page.  
        * Added an SNMP trap for a power fault condition on Gen8 servers.
        * Added the list of open source licenses to the login page.  
        * Added a Format Embedded Flash and reset iLO button to the Diagnostics page. When directed by Hewlett Packard Enterprise support, you can use this feature to recover Active Health System functionality.
        * Re-signed the Java IRC to extend the certificate expiration date. 
        * Re-signed the .NET IRC to extend the certificate expiration date. 
          * With this enhancement, the .NET IRC requires version 4.5.1 or later of the .NET Framework.
        * Added the ability to remove a SSL certificate and regenerate the iLO self-signed certificate. 
          * Note: HPE recommends using a CA signed certificate.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.60
changelog:
  -     The following issues are resolved in this version:
      
        *  iLO 4 unexpectedly restored itself to factory default settings when an user did not initiate the process. 
        * When Auto Power-On is set to Always Power On to Restore Last Power State, the server might not power on after a cold reset. 
        * False nonvolatile flash memory (NAND) test failures might occur after a firmware upgrade.
        * Incorrect RAM and Storage values are displayed on the HPE OneView for VMware vCenter tab.
        * Remote Support disk events include the text "Not Available" for the variables when data is missing.
        * Some Power Supply information is missing from the iLO web interface.
        * iLO displays Failed status instead of Disabled status when the Smart Array Cache Module battery is disconnected.
        * An iLO SSH port disconnection issue was observed after more than two days of continuous operation.
        * Values do not move up when the preceding entries in the Directory User Context fields are cleared.
        * Boot failures might occur when booting with a MicroSD card in Legacy mode.
        * Changed the resolution of a Redfish SSD wear field to display in percentage.
        * The date and time settings are reset after a firmware update.
        * The server powers on instead of shutting down when multiple power-on requests are sent.
      
      SECURITY FIXES:
      
        For the latest security bulletins and vulnerabilities addressed in this
      version, please visit:  
        https://support.hpe.com/hpesc/public/home  
      
      Security best practices:
      
        Please refer to the HPE Integrated Lights-Out Security Technology Brief for
      the latest on security best practices at:  
        http://www.hpe.com/support/iLO4_security_en


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.61
changelog:
  -     The following issues are resolved in this version:
      
        * Intermittent boot failures encountered when server boots from MicroSD card.
        * Fixed problem with AHS download that might have unreadable data for the current day.
        * iLO Web GUI sessions might not logoff at the end of timeout period.
        * Incorrect information displayed for Power Supply Bay in AHS viewer.
        * Licence hyperlink in Access Settings page of GUI leads to Page Not Found.
        * Unable to login to iLO CLI after setting iLO to factory defaults, requiring an additional iLO reset.
        * Unable to delete REST interface sessions with users having certain special characters.
        * SNMP may become unresponsive over a period of time.
      
      SECURITY:
      
        For the latest security bulletins and vulnerabilities, please visit:  
        https://support.hpe.com/hpesc/public/home  
      
      Security bulletins:
      
        * HPESBHF03866
      
      Security best practices:
      
        Please refer to the HPE Integrated Lights-Out Security Technology Brief for
      the latest on security best practices at:  
        http://www.hpe.com/support/iLO4_security_en


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.62
changelog:
  -     iLO could return a different host UUID after updating mezz firmware, and the
      new UUID would reset the configured WWN.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.30
changelog:
  -     The following issues are resolved in this version:
      
        * Compute modules do not power on after restoring power to Frame.
        * When you use iLO Virtual Media to install an operating system, installation might fail when iLO is configured to use the Shared Network Port.
        * In rare cases, a server runs out of available SSH sessions because the sessions are not reclaimed when a client disconnects.
        * iLO 5 unexpectedly restored itself to the factory default settings when a user did not initiate the process.
        * When Auto Power-On is set to Always Power On or Restore Last Power State, the server might not power on after a cold reset.
        * iLO cannot display the HP Ethernet 1Gb 4-port 331i Adapter MAC address.
        * NVMe drive model numbers are incorrect or inconsistent.
        * Clearing the oemHPE_usercntxt## from the command line clears the value, even though error messages might be displayed.
        * Fixed Single Sign-On when in CNSA mode.
        * Added support for RSA-PSS certificate signatures.
      
      For the latest security bulletins and vulnerabilities, please visit:  
      https://support.hpe.com/hpesc/public/home  
      
      Please refer to the HPE Integrated Lights-Out 5 Security Technology Brief for
      the latest on security best practices at:  
      http://www.hpe.com/support/ilo5-security-en


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.35
changelog:
  -     This version adds support for the following features and enhancements:
      
        * VGA Port Detect Override--Controls how devices connected to the system video port are detected. Dynamic detection protects the system from abnormal port voltages. This setting is enabled by default, and can be used for troubleshooting cases when there is no video output to displays, KVM concentrators, or active dongles.
        * DHCP Client ID override via iLO RESTful API.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.35
changelog:
  -     The following issues are resolved in this version:
      
        * Fix for improper Smart Array error reported: Cache module board backup power failed.
        * Fixed where iLO may become unresponsive after ejecting virtual media.
      
      SECURITY FIXES:
      
      For the latest security bulletins and vulnerabilities, please visit:  
      <https://support.hpe.com/hpesc/public/home>  
      
        * Security Bulletin HPESBHF03866
      
      Security best practices:
      
      Please refer to the HPE Integrated Lights-Out 5 Security Technology Brief for
      the latest on security best practices at:  
      <http://www.hpe.com/support/ilo5-security-enn>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.37
changelog:
  -     This version adds support for the following features and enhancements:
      
       \- Ability to backup and to restore a copy of the iLO configuration settings
      to/from iLO non-volatile memory via REST calls.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.37
changelog:
  -     The following issues are resolved in this version:
      
       \- Fix for "VGA Port Detect Override" to show video in all cases where
      monitors are installed.  
       \- Fix for intermittent file upload failures.  
       \- Fix for issues with Virtual Media in FIPS mode.  
       \- Fix for issues with simultaneous use of virtual DVD and floppy in FIPS
      mode.  
       \- Fix for USB floppy when used with ESXi 7 installation driver.  
       \- Fixed potential problem where iLO could continue to interact with system
      memory after it has been released by hpilo module.  
       \- Fix for erroneous reporting of disk drive overheating.  
       \- Fix for intermittent iLO communication error on HPE Apollo 2000.  
       \- Fix for potential RESTful API errors at boot with multiple NICs installed.  
       \- Fix to add iLO 5 NIC information into anonymous XML response.  
       \- Fixed false errors showing link lost on NICs when link never seen in IPMI.
      
      SECURITY FIXES:
      
       \- HPESBHF03894 - HPE iLO5 Local Bypass of Security Restrictions in Firmware
      Update


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.39
changelog:
  -      Fixed issue where pressing UID button on Gen10 server can occasionally cause server to power off


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.40
changelog:
  -      Ability to edit Maintenance Windows in Firmware & OS Software section
        * Added Password Complexity feature to Security > Access Settings
        * Enable/disable for overlay video showing Server Health Summary
        * Downgrade Policy - Specifies how iLO handles requests to downgrade any of the firmware types that you can update through iLO. 
        * Virtual NIC functionality (disabled by default)
        * Enabled One-button Secure Erase via Intelligent Provisioning
        * LDAP/Directory settings configurable via Redfish
        * Security Dashboard - displays the status of important security features, the Overall Security Status for the system, and the current configuration for the Security State and Server Configuration Lock features.
        * Support for Gemalto SafeNet and SafeNet AT key managers
        * InfoSight Optimized AHS Download
        * Show NVMe wear level
        * Workload performance advisor: provides server tuning recommendations to improve server performance


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.40
changelog:
  -     The following issues are resolved in this version:
      
        * User interface fixes and improvements
        * Fixed an issue where power supply status changes may be delayed
        * Device Inventory could display a parse error under Internet Explorer 11 when certain PCI Cards are installed
      
      SECURITY FIXES:
      
        * HPESBHF03907
      
      For the latest security bulletins and vulnerabilities, please visit:  
      <https://support.hpe.com/hpesc/public/home>  Security best practices:
      
      Please refer to the HPE Integrated Lights-Out 5 Security Technology Brief for
      the latest on security best practices at:  
      [http://www.hpe.com/support/ilo5-security-en](http://www.hpe.com/support/ilo5
      -security-enn)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.40-1.1
changelog:
  -     The following issues are resolved in this version:
      
        * User interface fixes and improvements.
        * The text "R&D Server" is incorrectly displayed in the iLO web interface navigation pane.
        * Fixed an issue where power supply status changes may be delayed.
        * Device Inventory could display a parse error under Internet Explorer 11 when certain PCI Cards are installed.
        * Improved shared network port out-of-band LOM resuscitation to reduce the scope and the frequency of system power-on/power-off during systems shutdown/reboot.
        * iLO communication issues in certain configurations where a server is set to Auto-Power-On after an AC power cycle.
      
      SECURITY FIXES:
      
        * HPESBHF03907
      
      For the latest security bulletins and vulnerabilities, please visit:  
      <https://support.hpe.com/hpesc/public/home>  Security best practices:
      
      Please refer to the HPE Integrated Lights-Out 5 Security Technology Brief for
      the latest on security best practices at:  
      [http://www.hpe.com/support/ilo5-security-en](http://www.hpe.com/support/ilo5
      -security-enn)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.45
changelog:
  -     The latest list of issues resolved can be found in the HP Virtual Connect
      Release Notes that can be found in the following URL**:
      **<http://www.hp.com/go/vc/manuals>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.50
changelog:
  -     The latest list of enhancements can be found in the HPE Virtual Connect
      Release Notes that can be found in the following URL**:
      **<http://www.hpe.com/info/vc/manuals>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.50
changelog:
  -     The latest list of issues resolved can be found in the HPE Virtual Connect
      Release Notes that can be found in the following URL**:
      **[http://www.hpe.com/info/vc/manuals](http://www.hpE.com/info/vc/manuals)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.62
changelog:
  -     The list of enhancements in 4.62 version can be found in the HPE Virtual
      Connect Release Notes at URL**: **<http://www.hpe.com/info/vc/manuals>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.62
changelog:
  -     The list of issues resolved in 4.62 version can be found in the HPE Virtual
      Connect Release Notes at URL**: **<http://www.hpe.com/info/vc/manuals>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.63
changelog:
  -     The list of issues resolved in 4.63 version can be found in the HPE Virtual
      Connect Release Notes at URL**: **<http://www.hpe.com/info/vc/manuals>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hp.com> 8.4.0
changelog:
  - 8.4.0 release (Severity: Medium)
  - ENHANCEMENTS
  - Added support for Integrated Lights-Out 3 (iLO 3)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hp.com> 10.0.0
changelog:
  - ENHANCEMENTS
  - Added support for HP ProLiant Gen9 Servers.

  - FIXES
  - When SNMP community string is configured as other than public in snmpd.conf file, all the webapp data is now populating in HP System Management Homepage (SMH) for Red Hat Enterprise Linux (RHEL) 6.5.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK3
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager.**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK3
changelog:
  -     *Problems Fixed:**
      
        * HPK3 firmware resolved an issue that caused the disk activity ring, which is located on NVME SSD drive carrier, to constantly spin regardless of drive activity status.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK4
changelog:
  -      Fixes a potential latency issue caused by an incorrect pre-fetch algorithm. 
        * Resolves an issue with a possible bus hang during a system reboot.
        * Once HPK4 is downloaded, the drive firmware cannot be changed back to an earlier firmware version (eg, HPK3 or HPK2) due to security changes.


author: Broadcom Automated Build User
changelog:
  - Changed version to 11.2
  - Updated libbrcmdfc library 
  - Updated libbrcmemsdm library 
  - Updated libbrcmhbaapi library


author: Broadcom Automated Build User
changelog:
  - Changed version to 11.4
  - Updated libbrcmdfc library 
  - Updated libbrcmemsdm library 
  - Updated libbrcmhbaapi library


author: Broadcom Automated Build User
changelog:
  - Changed version to 12.0
  - Updated libbrcmdfc library 
  - Updated libbrcmemsdm library 
  - Updated libbrcmhbaapi library


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD7-2.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPD7 do not need to update to HPD7 (B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD7-2.1
changelog:
  -     *Problems Fixed:**
      
        * This firmware fixes a potential incorrect data issue in write-cached enabled multi-initiator unaligned write environments, where reservation commands are used.
      
      **Problems Fixed for HPD7 (B):**
      
        * Component would fail to install drive firmware for drives present in a system configured with two or more external drive enclosures attached to an HP Host Bus Adapter H22x. The following message would be reported in the component log file - "Device appears more than once in tree". The drive firmware installation failure was not observed in configurations having only one external drive enclosure attached to an HP Host Bus Adapter H22x.
        * Component fails to update the firmware for drives connected behind an HP Smart Array P431 controller. Component reports the firmware update was successful. However, after a power cycle, the firmware version remains unchanged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD7-3.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager.**
        * **Customers who already installed firmware version HPD7 do not need to update to HPD7 (C).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD7-3.1
changelog:
  -     *Enhancements/New Featuresfor HPD7 (C):**
      
        * Adds support for HPE ProLiant Gen10 servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPDB
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPDB
changelog:
  -      Corrects a potential data integrity issue caused by an in process write retry incorrectly starting at the wrong location.  This issue was found during supplier ongoing reliability testing.
        * The firmware also includes emergency power off improvements.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPDB-2.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager**
        * **Customers who already installed firmware version HPDB do not need to update to HPDB(B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPDB-2.1
changelog:
  -      Added support for SmartRAID 3154-8e RAID controller.
        * Added support for HPE Smart Array P824i-p MR Gen10 Controller.


author: Emulex Automated Build User
changelog:
  - Initial RPM release
  - Changed version number to 6.4.9.2
  - Added libdfc 4.2.25
  - Added libdfc 3.2.23
  - Added libemulexhbaapi 2.3.b
  - Added libemsdm.so 1.1


author: Emulex Automated Build User
changelog:
  - Changed version number to 6.4.10.2
  - Fixed Bug 144987: Updated release string on RHEL 6
  - Fixed Bug 145311: Improved Requires and Provides tag entries


author: Emulex Automated Build User
changelog:
  - Changed version to 10.7
  - Updated libdfc library 
  - Updated libemsdm library 
  - Updated libemulexhbaapi library 
  - Added support for RHEL 7.2, SLES12 SP1


author: Broadcom Automated Build User
changelog:
  - Changed version to 11.2
  - Updated libdfc library 
  - Updated libemsdm library 
  - Updated libemulexhbaapi library


author: Broadcom Automated Build User
changelog:
  - Changed version to 11.4
  - Updated libdfc library 
  - Updated libemsdm library 
  - Updated libemulexhbaapi library


author: Broadcom Automated Build User
changelog:
  - Changed version to 12.0
  - Updated libdfc library 
  - Updated libemsdm library 
  - Updated libemulexhbaapi library


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3
changelog:
  -     *Problems Fixed:**
      
        * Self-initiated reset during ATI (Adjacent Track Interference) mitigation issue, where the drive reported a 06/29/04 (Self-Initiated Reset) to the controller.  Then the controller would re-establish link with the drive and resend the command.
        * Servo miscalculations that resulted in degraded drive performance.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3-2.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPD3 do not need to update to HPD3 (B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3-2.1
changelog:
  -     *Problems Fixed:**
      
        * Self-initiated reset during ATI (Adjacent Track Interference) mitigation issue, where the drive reported a 06/29/04 (Self-Initiated Reset) to the controller.  Then the controller would re-establish link with the drive and resend the command.
        * Servo miscalculations that resulted in degraded drive performance.
      
      **Problems Fixed for HPD3 (B):**
      
        * Component would fail to install drive firmware for drives present in a system configured with two or more external drive enclosures attached to an HP Host Bus Adapter H22x. The following message would be reported in the component log file - "Device appears more than once in tree". The drive firmware installation failure was not observed in configurations having only one external drive enclosure attached to an HP Host Bus Adapter H22x.
        * Component fails to update the firmware for drives connected behind an HP Smart Array P431 controller. Component reports the firmware update was successful. However, after a power cycle, the firmware version remains unchanged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3-3.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager.**
        * **Customers who already installed firmware version HPD3 do not need to update to HPD3 (C).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3-3.1
changelog:
  -     *Enhancements/New Features for HPD3 (C):**
      
        * Adds support for HPE ProLiant Gen10 servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5
changelog:
  -      Fixes a data integrity risk where a recoverable error can prevent a write command from completing properly.
        * Fixes a data integrity risk due to incorrect re-ordering of commands, when overlapped commands occur. 
        * Fixes a data integrity risk during very large blocks of sequential commands with a data transfer between 1020MB and 1024MB.
        * Fixes a data integrity risk during a sequential read and write workload when a recovered error is encountered, which could cause incomplete data to be read


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5-3.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPG5 do not need to update to HPG5(C).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5-4.1
changelog:
  -      Fixes a data integrity risk where a recoverable error can prevent a write command from completing properly.
        * Fixes a data integrity risk due to incorrect re-ordering of commands, when overlapped commands occur. 
        * Fixes a data integrity risk during very large blocks of sequential commands with a data transfer between 1020MB and 1024MB.
        * Fixes a data integrity risk during a sequential read and write workload when a recovered error is encountered, which could cause incomplete data to be read.


author: QLogic Corp <support@qlogic.com>
changelog:
  v6.02 build9:
  -------------
  Defect/Enhancement: Defect
  Problem: Get statistics failing on RHEL5/SLES10
  Solution: Use min data size for statistics required by driver
  Introduced: v6.00 build7
  Impact: HW: All adapters
  	OS: All supported Linux flavors
  	Protocol: FC, FCoE


author: QLogic Corp <support@qlogic.com>
changelog:
  v6.02 build12:
  -------------
  Defect/Enhancement: Defect
  Problem: CT Ping failing in ESXi 5.0/5.1
  Solution: Corrected code to get valid topology
  Introduced: v6.00 build10
  Impact: HW: All adapters
  	OS: All supported Linux flavors
  	Protocol: FC, FCoE

  v6.02 build11:
  -------------
  Defect/Enhancement: Defect
  Problem: Lun persistent names failing on RHEL7
  Solution: Use ATTR(S){} or SYSFS{} in udev rules based on udev version
  Introduced: v5.00 build6
  Impact: HW: All adapters
  	OS: All supported Linux flavors
  	Protocol: FC, FCoE

  v6.02 build10:
  -------------
  Defect/Enhancement: Enhancement 
  Problem: N/A
  Solution: Add D-Port Diagnosic info support
  Introduced: v6.02 build10
  Impact: HW: ISP2031, ISP8031
  	OS: All supported Linux flavors
  	Protocol: FC, FCoE


author: QLogic Corp <support@qlogic.com>
changelog:
  v6.02 build13:
  -------------
  Defect/Enhancement: Enhancement 
  Problem: N/A
  Solution: Add Fabric Priority support for ESXi
  Introduced: v6.02 build13
  Impact: HW: ISP2031, ISP8031
  	OS: VMware ESXi 5.1
  	Protocol: FC, FCoE


author: QLogic Corp <support@qlogic.com>
changelog:
  Defect/Enhancement: Enhancement
  Problem: N/A
  Solution: Add supported list of adapters in Provides section 
  Introduced: N/A
  Impact: HW: All adapters
  	OS: All supported Linux flavors
  	Protocol: FC, FCoE


author: QLogic Corp <support@qlogic.com>
changelog:
  v6.03 build1:
  -------------
  Defect/Enhancement: Enhancement
  Problem: N/A
  Solution: Added ISP2071 and ISP2271 support
  Introduced: v6.03 build1
  Impact: HW: ISP2071 and ISP2271 based adapters
  	OS: All supported Linux flavors
  	Protocol: FC


author: QLogic Corp <support@qlogic.com>
changelog:
  v6.03 build3:
  -------------
  Defect/Enhancement: Defect
  Problem: HBA_GetFcpTargetMapping fails for LUN number > 256
  Solution: Honor LUN addressing method while reading LUN numbers for
  	  HBA_GetFcpTargetMapping API with LUN numbers > 256
  Introduced: Day One
  Impact: HW: All adapters
  	OS: All supported Linux flavors
  	Protocol: FC, FCoE

  Defect/Enhancement: Defect
  Problem: HBA_SendScsiInquiry and HBA_SendReadCapacity fails
  	 for LUN number > 256
  Solution: Use SAM-2 LUN addressing for HBA_SendScsiInquiry and
  	  HBA_SendReadCapacity SNIA APIs for LUN numbers > 256
  Introduced: Day One
  Impact: HW: All adapters
  	OS: All supported Linux flavors
  	Protocol: FC, FCoE


author: QLogic Corp <support@qlogic.com>
changelog:
  v6.03 build10:
  -------------
  Defect/Enhancement: Defect
  Problem: Access denied messages seen on VMware ESXi 5.1
  Solution: Block get shared database count API for ESXi
  Introduced: Day One
  Impact: HW: All adapters
  	OS: VMware ESXi 5.1
  	Protocol: FC, FCoE

  Defect/Enhancement: Defect
  Problem: SDGetQoS API succeeds even if QoS region is not
  	 present in the flash
  Solution: Add QoS region check in SDGetQoS API
  Introduced: v6.02 build13
  Impact: HW: ISP2031, ISP8031, ISP2071, ISP2271
  	OS: VMware ESXi 5.1
  	Protocol: FC, FCoE

  Defect/Enhancement: Enhancement
  Problem: N/A
  Solution: Added ISP2261 support
  Introduced: v6.03 build10
  Impact: HW: ISP2261 based adapters
  	OS: All supported Linux flavors
  	Protocol: FC

  Defect/Enhancement: Enhancement
  Problem: N/A
  Solution: Add MPI and PEP versions for 27xx adapters
  Introduced: v6.03 build10
  Impact: HW: ISP2071, ISP2271, ISP2261
  	OS: All supported Linux flavors
  	Protocol: FC


author: QLogic Corp <support@qlogic.com>
changelog:
  v6.04 build3:
  -------------
  Defect/Enhancement: Enhancement
  Problem: N/A
  Solution: Add ppc64le (64-bit little endian PowerPC) API support
  Introduced: N/A
  Impact: HW: All adapters
  	OS: All supported Linux flavors
  	Protocol: FC, FCoE

  Defect/Enhancement: Enhancement
  Problem: N/A
  Solution: Add Online Flash update support
  Introduced: v6.04 build1
  Impact: HW: ISP2071, ISP2271, ISP2261
  	OS: All supported Linux flavors
  	Protocol: FC

  Defect/Enhancement: Enhancement
  Problem: N/A
  Solution: Add Smart SAN API support
  Introduced: v6.04 build2
  Impact: HW: All adapters
  	OS: All supported Linux flavors
  	Protocol: FC, FCoE

  Defect/Enhancement: Defect
  Problem: Flash update fails if online flash update feature is disabled
  	 or not supported by QLogic applications
  Solution: Allow flash update if online flash update feature is disabled
  	  or not supported by QLogic applications
  Introduced: v6.04 build1
  Impact: HW: ISP2071, ISP2271, ISP2261
  	OS: All supported Linux flavors
  	Protocol: FC


author: QLogic Corp <support@qlogic.com>
changelog:
  v6.04 build8:
  -------------
  Defect/Enhancement: Enhancement
  Problem: N/A
  Solution: Return FW status in BBCR API for port down case
  Introduced: v6.04 build6
  Impact: HW: ISP2071, ISP2271, ISP2261
  	OS: All supported Linux flavors
  	Protocol: FC

  v6.04 build6:
  -------------
  Defect/Enhancement: Enhancement
  Problem: N/A
  Solution: Add Buffer-to-Buffer Credit Recovery API support
  Introduced: v6.04 build6
  Impact: HW: ISP2071, ISP2271, ISP2261
  	OS: All supported Linux flavors
  	Protocol: FC

  Defect/Enhancement: Enhancement
  Problem: N/A
  Solution: Add Private Statistics API support
  Introduced: v6.04 build6
  Impact: HW: All adapters
  	OS: All supported Linux flavors
  	Protocol: FC, FCoE

  Defect/Enhancement: Defect
  Problem: Multiple application may do flash update simultaneously for
  	27xx adapters
  Solution: Use serial number based file for 27xx flash update token
  Introduced: v6.04 build1
  Impact: HW: ISP2071, ISP2271, ISP2261
  	OS: VMware ESXi 5.1
  	Protocol: FC

  v6.04 build5:
  -------------
  Defect/Enhancement: Enhancement
  Problem: N/A
  Solution: Read FW attributes at API initialization
  Introduced: v6.04 build5
  Impact: HW: All adapters
  	OS: All supported Linux flavors
  	Protocol: FC, FCoE

  v6.04 build4:
  -------------
  Defect/Enhancement: Enhancement
  Problem: N/A
  Solution: Validate Capabilities and Outage duration before FW activation
  Introduced: v6.04 build4
  Impact: HW: ISP2071, ISP2271, ISP2261
  	OS: All supported Linux flavors
  	Protocol: FC


author: QLogic Corp <support@qlogic.com>
changelog:
  v6.04 build12:
  -------------
  Defect/Enhancement: Defect
  Problem: timeout value is not properly converted from seconds into milliseconds
  Solution: Avoid converting timeout value twice into 
  	CPQFC_SendScsiCommandEx API
  Introduced: v6.04 build12
  Impact: HW: All adapters
  	OS: All supported Linux flavors
  	Protocol: FC, FCoE

  v6.04 build11:
  -------------
  Defect/Enhancement: Enhancement
  Problem: N/A
  Solution: Add CPQFC_SendScsiCommandEx API support
  Introduced: v6.04 build11
  Impact: HW: All adapters
  	OS: All supported Linux flavors
  	Protocol: FC, FCoE

  v6.04 build10:
  -------------
  Defect/Enhancement: Enhancement
  Problem: N/A
  Solution: Add DPort Diagnostics support
  Introduced: v6.04 build10
  Impact: HW: ISP2071, ISP2271, ISP2261
  	OS: All supported Linux flavors
  	Protocol: FC

  Defect/Enhancement: Enhancement
  Problem: N/A
  Solution: Add Extended Private Statistics API support
  Introduced: v6.04 build10
  Impact: HW: ISP2071, ISP2271, ISP2261
  	OS: All supported Linux flavors
  	Protocol: FC, FCoE

  Defect/Enhancement: Enhancement
  Problem: N/A
  Solution: Add Linux ARM (Euler) support
  Introduced: v6.04 build10
  Impact: HW: All adapters
  	OS: All supported Linux flavors
  	Protocol: FC, FCoE

  v6.04 build9:
  -------------
  Defect/Enhancement: Defect
  Problem: Flash MPI and PEP version are seen out-of-sync
  Solution: Read flash MPI and PEP verions from primary set
  Introduced: v6.04 build1
  Impact: HW: ISP2071, ISP2271, ISP2261
  	OS: All supported Linux flavors
  	Protocol: FC


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3
changelog:
  -     *Problems Fixed:**
      
        * This firmware resolves several drive issues including internal resets, firmware download functionality, and performance issues.  This firmware could improve the robustness of the system by eliminating these possible issues within the drive.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4-2.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPG4 do not need to update to HPG4(B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4-3.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPG4 do not need to update to HPG4(C).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4-3.1
changelog:
  -      Fixed the issue of Online firmware update fails when drives are connected behind AHCI controller.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4-4.1
changelog:
  -      This firmware improves potential timeouts that could occur during the write error recovery process, for drives that have head contaminant build up.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4-2.1
changelog:
  -     *Problems Fixed:**
      
        * Self-initiated reset during ATI (Adjacent Track Interference) mitigation issue, where the drive reported a 06/29/04 (Self-Initiated Reset) to the controller.  Then the controller would re-establish link with the drive and resend the command.
        * Servo miscalculations that resulted in degraded drive performance.
      
      **Problems Fixed for HPD4 (B): **
      
        * Linux Smart Component fails to update the firmware for drives connected behind an HP Smart Array P431 controller. Component reports the firmware update was successful. However, after a power cycle, the firmware version remains unchanged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4-3.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPD4 do not need to update to HPD4 (C).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4-3.1
changelog:
  -     *Problems Fixed:**
      
        * Self-initiated reset during ATI (Adjacent Track Interference) mitigation issue, where the drive reported a 06/29/04 (Self-Initiated Reset) to the controller.  Then the controller would re-establish link with the drive and resend the command.
        * Servo miscalculations that resulted in degraded drive performance.
      
      **Problems Fixed for HPD4 (B): **
      
        * Linux Smart Component fails to update the firmware for drives connected behind an HP Smart Array P431 controller. Component reports the firmware update was successful. However, after a power cycle, the firmware version remains unchanged.
      
      **Problems Fixed for HPD4 (C):**
      
        * Component would fail to install drive firmware for drives present in a system configured with two or more external drive enclosures attached to an HP Host Bus Adapter H22x. The following message would be reported in the component log file - "Device appears more than once in tree". The drive firmware installation failure was not observed in configurations having only one external drive enclosure attached to an HP Host Bus Adapter H22x.
        * Component fails to update the firmware for drives connected behind an HP Smart Array P431 controller. Component reports the firmware update was successful. However, after a power cycle, the firmware version remains unchanged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4-4.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager.**
        * **Customers who already installed firmware version HPD4 do not need to update to HPD4 (D).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4-4.1
changelog:
  -     *Enhancements/New Features for HPD4 (D):**
      
        * Adds support for HPE ProLiant Gen10 servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD6
changelog:
  -      Fixes a data integrity risk where stale data is mistakenly used from cache.
        * Fixes a data integrity risk where stale data is returned on an unaligned overlapped write-read operation.
        * Fixes a data integrity risk during a sequential read and write workload when a recovered error is encountered, which could cause incomplete data to be read.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD6-3.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPD6 do not need to update to HPD6(C).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.70
changelog:
  -     Update to this firmware version if any documented fixes or enhanced
      functionality provided by this version would be useful to your system.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.70
changelog:
  -     Onboard Administrator 4.70 provides support for the following enhancements:
      
      **Hardware additions**
      
        * BL460c Gen 10.
        * HPE 10GbE Pass-Thru Module.
        * Qualified support for HPE Integrity BL8x0c i6 Server Blade.
      
      Features**: additions and changes**
      
      **General**
      
        * Added support for Gen 10 Server and iLO5 features.
        * Added support for the enhanced KVM functionality in iLO5
        * Added support for HTTP boot option in the server boot options
        * Add support for HPE 10GbE Pass-Thru interconnect module.
        * Added support for HPE Integrity BL8x0c i6 Server Blade.
        * GUI, CLI, Smart components, help files, URLs, and product names rebranded to align with HPE branding guidelines.
        * Added a new SNMP trap to indicate that the power redundancy is restored in the enclosure.
        * Enhanced "SHOW ENCLOSURE TEMP" command output, to display the temperature readings like Current, Caution and Critical temperature threshold values for interconnect modules.
        * Added a provision to make sysName field to be set to DNS host name for the traps sent from Onboard Administrator.
      
      ** Security **
      
        * Adding support for CNSA approved algorithms and a new security mode - TOP_SECRET.
        * Added the ability to Enable/Disable cipher/protocol in FIPS OFF mode.
        * Added support for secured communication between HPE Embedded Remote Support functionality and the HPE Support Datacenters with the use of SHA-2 certificates.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.70
changelog:
  -     *General**
      
        * Addressed an issue where OA "update iLO all" command fails in an enclosure with maximum Blades.
        * Addressed an issue where a Warning Alert  was wrongly sent when a fan is reseated in an enclosure
        * Addressed an issue where the port mapping information for 560M Izzy adapter Mezz controller was not displayed correctly.
        * Addressed an issue where Remote Syslog logging would fail when OA failover happened in an IPv6 only environment.
        * Enhanced OA to bring the server from a power throttled state back to normal power state upon an OA reboot to circumvent an unwarranted emergency brake.
        * Fixed an issue where the Active and Standby OAs can have the same IP address in some rare situations.
        * Resolved an issue where a Gen9 server's host name gets cleared when the blade is rebooted.
        * Addressed an issue where server blade Power ON will be delayed in enclosures with OA Firmware Version 4.60 and managed by HPE OneView, when the OA module is reset until OneView refreshes the servers.
      
      **Security**
      
      The following security vulnerabilities were fixed:
      
        * CVE-2016-5387- Addressed a vulnerability which might allow remote attackers to redirect an application's outbound HTTP traffic to an arbitrary proxy server via a crafted Proxy header in an HTTP request.
        * CVE-2016-2183- Addressed a vulnerability against TLS ciphers with 64bit block size in which makes it easier for remote attackers to obtain cleartext data via an attack against a long-duration encrypted session
        * CVE-2016-6515 - Addressed a vulnerability in OpenSSH which did not limit password lengths for password authentication, which allows remote attackers to cause a denial of service via a long string.
        * CVE-2015-8215 - Addressed a vulnerability IPv6 stack which does not validate attempted changes to the MTU value, which allows context-dependent attackers to cause a denial of service.
        * Addressed issue where in Onboard Administrator was vulnerable to Buffer overflow.
        * Added the HSTS[HTTP strict transport security] support  in OA.
        * Addressed a memory corruption vulnerability in the post-authentication sshd process.
      
      **Issues and workarounds**
      
      **Browsers**
      
        * OA GUI is not accessible in Chrome versions 43.0.2357.10 to 44.0.2383.The issue was caused by a "regression" in Chrome (or WebKit). Customers should use an alternative browser like Firefox or Internet Explorer or try a different version of Chrome.
        * SSO-to-iLO connection from the OA using an iLO host name fails with Microsoft Internet Explorer11 on Windows 8.On a Windows 8 system with Internet Explorer 10 or Internet Explorer 11, if the OA web GUI session is loaded using a host name instead of an IP address, an attempt to open an iLO window using SSO from the OA web GUI might result in the iLO page loading in the OA web GUI window instead of the intended new window. This issue was determined to be a bug in Internet Explorer and is expected to be fixed in a future release or update for Internet Explorer. To work around this issue, either use an IP address to load the OA Web GUI, or turn off Protected Mode for the appropriate zone in Internet Explorer's settings. This issue occurs only on Internet Explorer browsers.
      
      **FIPS**
      
      Certificates smaller than 2048 bits in size are not compliant with FIPS
      requirements as enforced by the OA firmware starting with OA 4.20. When the OA
      running OA firmware version 4.40 or greater is operating in FIPS Mode ON/DEBUG
      and is configured with a 1024-bit LDAP certificate that was installed when
      running a previous version of OA firmware, FIPS Mode ON/DEBUG is considered to
      be operating in a degraded state due to the presence of the non-compliant
      certificate. While operating in this FIPS-Degraded Mode operational state,
      attempts to set FIPS Mode OFF from the OA GUI Network Access>FIPS tab will
      fail and show the error message The selected FIPS mode is already enabled.
      When the non-compliant certificate is removed, the FIPS-Degraded operational
      status is cleared, FIPS Mode can then be successfully set to OFF from the GUI
      interface. Note that the OA CLI command SET FIPS MODE OFF can be successfully
      used to set FIPS Mode OFF even with non-compliant 1024-bit LDAP certificates
      installed in the OA.
      
      **IRC**
      
      Unable to open .net IRC console for Gen10 Blades, Gen9 Blades also have the
      same issue. The Java applet and Webstart however, loads but the virtual media
      mounting fails. The work around is to launch the IRC through IRC Application
      (HP Lights-Out Stand Alone Remote Console) which is installed on terminal
      client.
      
      **EFM **
      
      To use EFM on Gen 10 Blades, please select options/filters "_Make Bootable ISO
      file" and _"_Enclosure Firmware Management"_ while creating custom SPP ISO on
      HPSUM 8.0.0. Please refer to HPSUM 8.0.0 User guide for further details.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.71
changelog:
  -     Onboard Administrator 4.71 provides support for the following enhancements:
      
      ** Security **
      
           CAC Feature: The authentication mechanism in Onboard Administrator has been enhanced to support DoD  
           Common Access Card Personal Identification Verification devices. This feature enhances security by  
           supporting multi factor authentication and below are the core elements of the new Authorization mechanism  
           listed below:
      
        * During Authentication (occurs during SSL session establishment): Verifying revocation status using Online  
      Certificate Status Protocol (OCSP) or Offline Certificate Revocation List
      (CRL).
      
        * During Authentication (after SSL session establishment): The certificate's Subject Alternate Name (SAN)  
      or the Subject is validated against the User Principal Name (UPN) of the
      corresponding principal in Active Directory.
      
        * It is important to note that the local user accounts in OA are disabled in CAC mode.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.71
changelog:
  -     *Security**
      
      The following security issues were fixed:
      
        * Removed the support to generate keys with SHA1 in FIPS mode, as per the latest FIPS standards SHA1 is no longer allowed.
        * Removed the support for 1024 DH primes in FIPS mode, as per the latest FIPS standards.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.80
changelog:
  -     Onboard Administrator 4.71 provides support for the following enhancements:
      
      **Hardware additions**
      
        * BL460c Gen 10.
        * HPE 10GbE Pass-Thru Module.
        * Qualified support for HPE Integrity BL8x0c i6 Server Blade.
      
      Features**: additions and changes**
      
      **General**
      
        * Added support for Gen 10 Server and iLO5 features.
        * Added support for the enhanced KVM functionality in iLO5
        * Added support for HTTP boot option in the server boot options
        * Add support for HPE 10GbE Pass-Thru interconnect module.
        * Added support for HPE Integrity BL8x0c i6 Server Blade.
        * GUI, CLI, Smart components, help files, URLs, and product names rebranded to align with HPE branding guidelines.
        * Added a new SNMP trap to indicate that the power redundancy is restored in the enclosure.
        * Enhanced "SHOW ENCLOSURE TEMP" command output, to display the temperature readings like Current, Caution and Critical temperature threshold values for interconnect modules.
        * Added a provision to make sysName field to be set to DNS host name for the traps sent from Onboard Administrator.
      
      ** Security **
      
        * Adding support for CNSA approved algorithms and a new security mode - TOP_SECRET.
        * Added the ability to Enable/Disable cipher/protocol in FIPS OFF mode.
        * Added support for secured communication between HPE Embedded Remote Support functionality and the HPE Support Datacenters with the use of SHA-2 certificates.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.80
changelog:
  -     *General**
      
        * Addressed an issue where OA "update iLO all" command fails in an enclosure with maximum Blades.
        * Addressed an issue where a Warning Alert  was wrongly sent when a fan is reseated in an enclosure
        * Addressed an issue where Remote Syslog logging would fail when OA failover happened in an IPv6 only environment.
        * Enhanced OA to bring the server from a power throttled state back to normal power state upon an OA reboot to circumvent an unwarranted emergency brake.
        * Fixed an issue where the Active and Standby OAs can have the same IP address in some rare situations.
        * Resolved an issue where a Gen9 server's host name gets cleared when the blade is rebooted.
        * Addressed an issue where server blade Power ON will be delayed in enclosures with OA Firmware Version 4.60 and managed by HPE OneView, when the OA module is reset until OneView refreshes the servers.
      
      **Security**
      
      The following security vulnerabilities were fixed:
      
        * CVE-2016-5387- Addressed a vulnerability which might allow remote attackers to redirect an application's outbound HTTP traffic to an arbitrary proxy server via a crafted Proxy header in an HTTP request.
        * CVE-2016-2183- Addressed a vulnerability against TLS ciphers with 64bit block size in which makes it easier for remote attackers to obtain cleartext data via an attack against a long-duration encrypted session
        * CVE-2016-6515 - Addressed a vulnerability in OpenSSH which did not limit password lengths for password authentication, which allows remote attackers to cause a denial of service via a long string.
        * CVE-2015-8215 - Addressed a vulnerability IPv6 stack which does not validate attempted changes to the MTU value, which allows context-dependent attackers to cause a denial of service.
        * Addressed issue where in Onboard Administrator was vulnerable to Buffer overflow.
        * Added the HSTS[HTTP strict transport security] support  in OA.
        * Addressed a memory corruption vulnerability in the post-authentication sshd process.
      
      **Issues and workarounds**
      
      **Browsers**
      
        * OA GUI is not accessible in Chrome versions 43.0.2357.10 to 44.0.2383.The issue was caused by a "regression" in Chrome (or WebKit). Customers should use an alternative browser like Firefox or Internet Explorer or try a different version of Chrome.
        * SSO-to-iLO connection from the OA using an iLO host name fails with Microsoft Internet Explorer11 on Windows 8.On a Windows 8 system with Internet Explorer 10 or Internet Explorer 11, if the OA web GUI session is loaded using a host name instead of an IP address, an attempt to open an iLO window using SSO from the OA web GUI might result in the iLO page loading in the OA web GUI window instead of the intended new window. This issue was determined to be a bug in Internet Explorer and is expected to be fixed in a future release or update for Internet Explorer. To work around this issue, either use an IP address to load the OA Web GUI, or turn off Protected Mode for the appropriate zone in Internet Explorer's settings. This issue occurs only on Internet Explorer browsers.
      
      **FIPS**
      
      Certificates smaller than 2048 bits in size are not compliant with FIPS
      requirements as enforced by the OA firmware starting with OA 4.20. When the OA
      running OA firmware version 4.40 or greater is operating in FIPS Mode ON/DEBUG
      and is configured with a 1024-bit LDAP certificate that was installed when
      running a previous version of OA firmware, FIPS Mode ON/DEBUG is considered to
      be operating in a degraded state due to the presence of the non-compliant
      certificate. While operating in this FIPS-Degraded Mode operational state,
      attempts to set FIPS Mode OFF from the OA GUI Network Access>FIPS tab will
      fail and show the error message The selected FIPS mode is already enabled.
      When the non-compliant certificate is removed, the FIPS-Degraded operational
      status is cleared, FIPS Mode can then be successfully set to OFF from the GUI
      interface. Note that the OA CLI command SET FIPS MODE OFF can be successfully
      used to set FIPS Mode OFF even with non-compliant 1024-bit LDAP certificates
      installed in the OA.
      
      **IRC**
      
      Unable to open .net IRC console for Gen10 Blades, Gen9 Blades also have the
      same issue. The Java applet and Webstart however, loads but the virtual media
      mounting fails. The work around is to launch the IRC through IRC Application
      (HP Lights-Out Stand Alone Remote Console) which is installed on terminal
      client.
      
      **EFM **
      
      To use EFM on Gen 10 Blades, please select options/filters "_Make Bootable ISO
      file" and _"_Enclosure Firmware Management"_ while creating custom SPP ISO on
      HPSUM 8.0.0. Please refer to HPSUM 8.0.0 User guide for further details.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.85
changelog:
  -     Onboard Administrator 4.85 provides support for the following enhancements:
      
      **Hardware additions**
      
        * HPE D2500sb Storage Blade
      
      Features**: additions and changes**
      
      **General**
      
        * Onboard Administrator has been enhanced to allow configuring an IPv6 address as SNMP EngineID.
        * Onboard Administrator has been enhanced to allow configuring a user defined SSH port number. This will allow users to configure a non-standard SSH port instead of the default SSH port 22.
      
      ** Security**
      
      General Data Protection Requirements (GDPR) support added in Onboard
      Administrator for HPE Embedded Remote Support solution. The HPE passport
      username will now be stored in an encrypted form.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.85
changelog:
  -     *General**
      
        * Addressed an issue where SNMP trap cpqRackEnclosureManagerLinkUp was not sent after an Onboard Administrator failover.
        * Addressed online help content issues seen in the previous version of Onboard Administrator.
      
      **Security**
      
         The following security vulnerabilities were fixed:
      
        * CVE-2017-8105 - Addressed a memory corruption vulnerability caused by a buffer overflow.
        * CVE-2016-10244 - Addressed a vulnerability which might allow a remote attacker to cause denial-of-service via a crafted file.
      
      **Issues and workarounds**
      
      **Browsers**
      
        * OA GUI is not accessible in Chrome versions 43.0.2357.10 to 44.0.2383.The issue was caused by a "regression" in Chrome (or WebKit). Customers should use an alternative browser like Firefox or Internet Explorer or try a different version of Chrome.
        * SSO-to-iLO connection from the OA using an iLO host name fails with Microsoft Internet Explorer11 on Windows 8. On a Windows 8 system with Internet Explorer 10 or Internet Explorer 11, if the OA web GUI session is loaded using a host name instead of an IP address, an attempt to open an iLO window using SSO from the OA web GUI might result in the iLO page loading in the OA web GUI window instead of the intended new window. This issue was determined to be a bug in Internet Explorer and is expected to be fixed in a future release or update for Internet Explorer. To work around this issue, either use an IP address to load the OA Web GUI, or turn off Protected Mode for the appropriate zone in Internet Explorer's settings. This issue occurs only on Internet Explorer browsers.
      
      **FIPS**
      
      Certificates smaller than 2048 bits in size are not compliant with FIPS
      requirements as enforced by the OA firmware starting with OA 4.20. When the OA
      running OA firmware version 4.40 or greater is operating in FIPS Mode ON/DEBUG
      and is configured with a 1024-bit LDAP certificate that was installed when
      running a previous version of OA firmware, FIPS Mode ON/DEBUG is considered to
      be operating in a degraded state due to the presence of the non-compliant
      certificate. While operating in this FIPS-Degraded Mode operational state,
      attempts to set FIPS Mode OFF from the OA GUI Network Access>FIPS tab will
      fail and show the error message The selected FIPS mode is already enabled.
      When the non-compliant certificate is removed, the FIPS-Degraded operational
      status is cleared, FIPS Mode can then be successfully set to OFF from the GUI
      interface. Note that the OA CLI command SET FIPS MODE OFF can be successfully
      used to set FIPS Mode OFF even with non-compliant 1024-bit LDAP certificates
      installed in the OA.
      
      **IRC**
      
      Unable to open .net IRC console for Gen10 Blades, Gen9 Blades also have the
      same issue. The Java applet and Webstart however, loads but the virtual media
      mounting fails. The work around is to launch the IRC through IRC Application
      (HP Lights-Out Stand Alone Remote Console) which is installed on terminal
      client.
      
      **EFM**
      
      To use EFM on Gen 10 Blades, please select options/filters "_Make Bootable ISO
      file" and _"_Enclosure Firmware Management"_ while creating custom SPP ISO on
      HPSUM 8.0.0. Please refer to HPSUM 8.0.0 User guide for further details.
      
      **CAC**
      
        * In the CAC mode SSH, Telnet and XML Reply protocols will be disabled.
        * Linked enclosure login will not work if the linked enclosure in CAC mode.
        * If accurate Service account details are not provided, LDAP user login with certificate will fail.
        * It is highly recommended to establish a recovery plan before getting started with CAC.  If something goes wrong with the OA configuration, the OA may be recovered through the serial port or Insight Display panel and USB KEY. Both methods require physical access to the OA.  However, if an LCD PIN has been configured (and forgotten) and local accounts have been disabled or CAC has been incorrectly configured then, the only way to recover is through a serial port. The two most common situations where OA recovery is needed are when LDAP has been configured incorrectly with local accounts disabled or when CAC has been configured without certificate access.
      
      **Configurable SSH Port Number                                               **
      
      If a Standby OA is running firmware version less than 4.85 and it is updated
      to firmware version greater than or equal to 4.85 using synchronize firmware
      feature from Active OA, after the firmware update and reboot of the Standby
      OA, SSH port will not open in the configured port number. The work around is
      to reboot the Standby OA and SSH port will open in the configured port in next
      boot. This issue will not occur in the case where SSH port is configured to
      default port 22 in the Active OA.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.90
changelog:
  -     *General**
      
        * Addressed an issue where Onboard Administrator is not reachable when the port speed changes from 100M to 1000M in auto-negotiation mode. This issue is described by Customer Advisory : [https://support.hpe.com/hpsc/doc/public/display?sp4ts.oid=1844065&docLocale=en_US&docId=emr_na-c04866545](https://support.hpe.com/hpsc/doc/public/display?sp4ts.oid=1844065&docLocale=en_US&docId=emr_na-c04866545)
        * Addressed an issue where the DHCPv6 service does not start after an Onboard Administrator reboots causing it to reboot again after 15 minutes.
        * Addressed an issue related to ssl protocols enable or disable in the Onboard Administrator Command Line Interface (CLI) where proper error message is displayed. When the password entered is less than eight characters, the ambient temperature of the BL460c Gen10 blade is not displayed.
        *  Addressed issues in Onboard Administrator GUI pages related to: 
          1. Power management
          2. Front view display of BL460c Gen10 blade
      
          3. Login feature into linked enclosure and Two-factor authentication
      
        * Addressed an issue where syslog messages were not added for dynamic dns setting and LDAP group access changes.
        * Addressed an issue where SNMP GET for Onboard Administrator system description OID displays a wrong value.
        * Addressed an issue where Blade Switch 6125G firmware version is not displayed after rebooting OA.
        * Addressed an issue where Onboard Administrator responds to internal private IP ping requests from management interface.
        * Addressed the issue of delay in the powering of the blades after an enclosure power cycle in a VCM managed enclosure.
        * Addressed an issue in the SNMP where power supply OK traps are not sent out after an enclosure power cycle.
        * Addressed the issues related to user certificate usage in the Onboard Administrator where the same certificate cannot be used for multiple users and checking the syntax of IPv6 address if used in the certificate.
        * Addressed the issues present in the previous versions of the Onboard Administrator online help.
        * Addressed an issue in FIPS ON mode where Onboard Administrator CLI will display information about the password requirements when an invalid password in entered by the user.
        * Fixed an issue related to ambient temperature display of Gen10 blades in Command Line Interface (CLI).
        * Fixed an issue in First Time Setup Wizard page in GUI where in FIPS ON mode, user will not able to set DEBUG to ON.
        * Addressed an issue where messages are not logged in syslog when Device and Interconnects bay access are updated for a LDAP group.
        * Fixed an issue related to Blade part number display in OA GUI and CLI.
      
      **Security**
      
        The following security vulnerabilities are fixed:
      
        * CVE-2018-0732- Addressed the issue where the possibility of a malicious server sending a large prime value to the client from DH (E) based ciphersuite during the key agreement in a TLS handshake resulting in the client to take a long time to generate a key with the prime and exploited in a Denial Of Service attack.
        * CVE-2018-0737- Addressed the issue of vulnerability of the OpenSSL RSA Key generation algorithm to the cache timing side channel attack.
      
      **Issues and workarounds**
      
      **Browsers**
      
        * OA GUI is not accessible in Chrome versions 43.0.2357.10 to 44.0.2383.The issue was caused by a "regression" in Chrome (or WebKit). Customers should use an alternative browser like Firefox or Internet Explorer or try a different version of Chrome.
        * SSO-to-iLO connection from the OA using an iLO host name fails with Microsoft Internet Explorer11 on Windows 8. On a Windows 8 system with Internet Explorer 10 or Internet Explorer 11, if the OA web GUI session is loaded using a host name instead of an IP address, an attempt to open an iLO window using SSO from the OA web GUI might result in the iLO page loading in the OA web GUI window instead of the intended new window. This issue was determined to be a bug in Internet Explorer and is expected to be fixed in a future release or update for Internet Explorer. To work around this issue, either use an IP address to load the OA Web GUI, or turn off Protected Mode for the appropriate zone in Internet Explorer's settings. This issue occurs only on Internet Explorer browsers.
      
      **FIPS**
      
      Certificates smaller than 2048 bits in size are not compliant with FIPS
      requirements as enforced by the OA firmware starting with OA 4.20. When the OA
      running OA firmware version 4.40 or greater is operating in FIPS Mode ON/DEBUG
      and is configured with a 1024-bit LDAP certificate that was installed when
      running a previous version of OA firmware, FIPS Mode ON/DEBUG is considered to
      be operating in a degraded state due to the presence of the non-compliant
      certificate. While operating in this FIPS-Degraded Mode operational state,
      attempts to set FIPS Mode OFF from the OA GUI Network Access>FIPS tab will
      fail and show the error message The selected FIPS mode is already enabled.
      When the non-compliant certificate is removed, the FIPS-Degraded operational
      status is cleared, FIPS Mode can then be successfully set to OFF from the GUI
      interface. Note that the OA CLI command SET FIPS MODE OFF can be successfully
      used to set FIPS Mode OFF even with non-compliant 1024-bit LDAP certificates
      installed in the OA.
      
      **IRC**
      
      Unable to open .net IRC console for Gen10 Blades, Gen9 Blades also have the
      same issue. The Java applet and Webstart however, loads but the virtual media
      mounting fails. The work around is to launch the IRC through IRC Application
      (HPE Lights-Out Stand Alone Remote Console) which is installed on terminal
      client.
      
      **EFM**
      
      To use EFM on Gen 10 Blades, please select options/filters "_Make Bootable ISO
      file" and _"_Enclosure Firmware Management"_ while creating custom SPP ISO on
      HPE SUM 8.0.0. Please refer to HPE SUM 8.0.0 User guide for further details.
      
      **CAC**
      
        * In the CAC mode SSH, Telnet and XML Reply protocols will be disabled.
        * Linked enclosure login will not work if the linked enclosure in CAC mode.
        * If accurate Service account details are not provided, LDAP user login with certificate will fail.
        * It is highly recommended to establish a recovery plan before getting started with CAC.  If something goes wrong with the OA configuration, the OA may be recovered through the serial port or Insight Display panel and USB KEY. Both methods require physical access to the OA.  However, if an LCD PIN has been configured (and forgotten) and local accounts have been disabled or CAC has been incorrectly configured then, the only way to recover is through a serial port. The two most common situations where OA recovery is needed are when LDAP has been configured incorrectly with local accounts disabled or when CAC has been configured without certificate access.
      
      **Configurable SSH Port Number                                               **
      
      If a Standby OA is running firmware version less than 4.85 and it is updated
      to firmware version greater than or equal to 4.85 using synchronize firmware
      feature from Active OA, after the firmware update and reboot of the Standby
      OA, SSH port will not open in the configured port number. The work around is
      to reboot the Standby OA and SSH port will open in the configured port in next
      boot. This issue will not occur in the case where SSH port is configured to
      default port 22 in the Active OA.


author: Chad Dupuis <Linux_SWdeliverables@external.groups.hp.com> 3.0-1
changelog:
  - Initial version that works with inbox fibre channel drivers only
    (Severity: Critical)
  - Fix grep statement that parses /sys/block for sd devices in lssd
    (Severity: Minor)
  - Add support for five character device names in lssd (Severity: Minor)
  - Fix parsing of sdsd* devices in lssd


author: Chad Dupuis <Linux_SWdeliverables@external.groups.hp.com> 3.1-1
changelog:
  - Added support for Brocade HBAs (Severity: Medium)
  - Added support for getting WWN from MSA2xxx devices in scsi_info


author: Kumar Rahul<Linux_SWdeliverables@external.groups.hp.com> 3.2-5
changelog:
  - Removed installation check for kernel 2.6 and addded Installation check for Rhel5.3 and SLES10 SP3 onwards


author: Shreya Roy Chowdhury<Linux_SWdeliverables@external.groups.hp.com> 3.2-6
changelog:
  - Corrected Link state display information for Qlogic Adapters
  - Added MSA G3 support in Scsi_info.h


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4
changelog:
  -     *Enhancements/New Features:**
      
        * Production signing keys applied to code.
        * Enhanced code to meet signal specification for the TX differential voltage and de-emphasis level.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG6
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG6
changelog:
  -     *Problems Fixed:**
      
        * Firmware improves a NAND threshold level to strengthen differentiation of NAND states to mitigate excessive reallocation of NAND Blocks (Grown Bad Blocks). For important information about this resolved issue, refer to HPE Customer Bulletin [a00027721](http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=emr_na-a00027721en_us).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG6-2.1
changelog:
  -      Firmware improves a NAND threshold level to strengthen differentiation of NAND states to mitigate excessive reallocation of NAND Blocks (Grown Bad Blocks). For important information about this resolved issue, refer to HPE Customer Bulletin [a00027721](http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=emr_na-a00027721en_us).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG8
changelog:
  -      During numerous unexpected power cycles and if a SATA link error is immediately followed with asynchronous power loss, there may be a failure to properly flush all cached data to NAND. For more information on this issue, refer to Customer Advisory <https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00048321en_us>.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPGB
changelog:
  -      Fixed issue to a read-disturb mechanism within the NAND induced only during 4K reads with partially programed blocks. The NAND read time is modified to prevent the impact of the reads. This change prevents premature or false failure of the drive.
        * Fix to a non-exploitable vulnerability in the firmware download process. Corrected FW will increment the security version to ensure that all SSDs receiving the update will not be capable of downloading previous FW with the issue.  Regression back to an earlier version of firmware will not be possible.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 24.23.0-0019-2.1
changelog:
  -     Customers who already installed firmware version 24.23.0-0019 do not need to
      update to 24.23.0-0019 (B).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3-2.1
changelog:
  -     *Problems Fixed:**
      
        * Firmware resolves a data mismanagement issue associated with unaligned sequential write operations.
      
      **Problems Fixed for HPG3 (B):**
      
        * Component would fail to install drive firmware for drives present in a system configured with two or more external drive enclosures attached to an HP Host Bus Adapter H22x. The following message would be reported in the component log file - "Device appears more than once in tree". The drive firmware installation failure was not observed in configurations having only one external drive enclosure attached to an HP Host Bus Adapter H22x.
        * Component fails to update the firmware for drives connected behind an HP Smart Array P431 controller. Component reports the firmware update was successful. However, after a power cycle, the firmware version remains unchanged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3-3.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager.**
        * **Customers who already installed firmware version HPG3 do not need to update to HPG3 (C).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3-3.1
changelog:
  -     *Enhancements/New Features for HPG3 (C):**
      
        * Adds support for HPE ProLiant Gen10 servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3-4.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPG3 do not need to update to HPG3(D).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3-5.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPG3 do not need to update to HPG3(E).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3-5.1
changelog:
  -      Fixed the issue of Online firmware update fails when drives are connected behind AHCI controller.
        * Firmware fixes intermittent data corruption issue associated with unaligned sequential write operations.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3-6.1
changelog:
  -      Firmware fixes intermittent data corruption issue associated with unaligned sequential write operations.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2018.02.01
changelog:
  -     Added support for the following:
      
      UEFI:
      
        * Modify Fibre Channel over Ethernet (FCoE) code base to compile with Unreal Development Kit 2015(UDK2015) for access to new Unified Extensible Firmware Interface (UEFI)
        * Implement HP Unified Extensible Firmware Interface (UEFI) reqs - spec changes from 2.2 and 2.3
      
      Firmware:
      
        * Security Encryption for Internet Small Computer System Interface(iSCSI) Challenge Handshake Authentication Protocol (CHAP) and Data Center Interconnect(DCi) config data
        * Platform Management Components Intercommunication (PMCI) v1.1.0 - which also covers Network Controller Sideband Interface (NC-SI) requirements V1.01
        * Active Health System (AHS) Device Capabilities support in the Auxiliary Port (Aux) power
      
      Updated CNA (XE100 series) firmware:
      
      **Contains:**
      
      CNA (XE100 series) firmware 11.4.1231.6


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2018.02.01
changelog:
  -     Fixed the following:
      
      UEFI:
      
        * Boot From SAN(BFS) volume is seen offline during Microsoft Windows 2016 Operating System install with 11.2.1263.19 Firmware
        * Removal of Boot entry from card Basic Input /Output System(BIOS) caused a red screen on HPE ProLiant ML350 Gen10 Server
      
      BIOS/Firmware:
      
        * HP FlexFabric 20Gb 2-port 650M Adapter goes missing from Operating System (OS) post 1.1.183.624 firmware flash
        * Excessive number of timeouts overflowing Noted All or Nothing Gate(NAND)
        * For HP StoreFabric CN1200E 10Gb Converged Network Adapter and HPE StoreFabric CN1200E-T 10GBASE-T Converged Network Adapter Firmware Active Health System (AHS) log incorrect part number
        * Name of HP StoreFabric CN1200E 10Gb Converged Network Adapter show incomplete in Active Health System (AHS)
        * For HP FlexFabric 20Gb 2-port 650FLB Adapter "Function Driver" is missing in Active Health System (AHS) field
        * Ports of HP FlexFabric 10Gb 2-port 556FLR-SFP+ Adapter/HPE StoreFabric CN1200E-T 10GBASE-T Converged Network Adapter will become Disconnected in ESXI6.0 update 3 Operating System
        * Server Profile Health Status is not stable during Power on


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2018.02.02
changelog:
  -     Updated CNA (XE100 series) firmware:
      
      **Contains:**
      
      CNA (XE100 series) firmware 11.4.1253.0


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2018.02.02
changelog:
  -     Fixed the following:
      
        * Uplink status on down link
        * PFC enable/disable feature
      
      For more details please go through the document titled " HPE Network Adapters
      - On Certain HPE ProLiant Gen9 Servers Running Windows Server 2016 And
      Configured With Certain Network Adapters, a Series of Windows System Event Log
      Messages #153 On Windows 2016 May Be Encountered" which is available at the
      following link:
      
      <https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00046322en_us>
      
      And the document titled "HPE Network Adapters - On Any HPE ProLiant
      Server Running VMware ESXi 6.0 or VMware ESXi 6.5, And Configured
      With Certain Network Adapters, The Network Ports May Show as Up,
      When These Should Show as Down In HPE iLO and In the OS" which is
      available at the following link:
      
      <https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00046319en_us>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2018.06.01
changelog:
  -     We have separate components to update fibre channel and converged network
      adapters.  This is a converged network adapter update component.  
        
      Updated CNA (XE100 series) firmware
      
      **Firmware**
      
      Contains:  
      CNA (XE100 series) firmware 12.0.1110.11


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2018.06.01
changelog:
  -     Fixed the following:
      
        * Add a check for zero capacity LUNs (Logical Units) and avoid creating device path for them.
        * HP StoreFabric CN1200E Dual Port Converged Network Adapter FCoE function only show "Slot 3 Port 3:CN1200E Function 2-FCoE"


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2018.06.02
changelog:
  -     We have separate components to update fibre channel and converged network
      adapters.  This is a converged network adapter update component.  
        
      Updated CNA (XE100 series) firmware
      
      **Firmware**
      
      Contains:  
      CNA (XE100 series) firmware 12.0.1110.2302


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2018.06.02
changelog:
  -     Fixed the following:
      
        * After update to firmware version 11.2.1263.19 the link lost is observed on HPE FlexFabric 10Gb 2-port 556FLR-T Adapter


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2019.03.01
changelog:
  -     Fixed the following:
      
        * Fixed unexpected behavior in Active Health System (AHS) logs show World Wide Node Name (wwnn) & World Wide Port Name (wwpn) in reverse order.
        * Fixed unexpected behavior with HP FlexFabric 20Gb 2-port 650FLB Adapter, HP FlexFabric 20Gb 2-port 650M Adapter cards does not complete to boot to Linux SUSE Linux Enterprise Server 12 Service Pack 3(SLES12 SP3) Operating System (OS) when both adapter are enabled for Fibre Channel over Ethernet (FCoE) boot.
        * Microsoft Windows Server 2012 R2 Hyper-V Storage Area Network (SAN) Disconnect.
        * Link lost with firmware version 11.2.1263.19
        * "FW not responding" message seen on card when creating Virtual Function (VF) in loop for HPE StoreFabric CN1200E-T 10GBASE-T Converged Network Adapter [NIC+ iSCSI] in Gen10 server.
        * HP FlexFabric 20Gb 2-port 650FLB Adapter - Loss of access to storage after Virtual Connect (VC) login redistribution
        * HP StoreFabric CN1200E Dual Port Converged Network Adapter does not complete to boot in Legacy Mode on Gen 9 Server
        * Emulex Peripheral Component Interconnect (PCI) slot Network Interface Connector (NIC) reported as device path instead of product name
        * Unable to disable shared memory feature in Human Interface Infrastructure (HII) menu
        * 650M Adapter has some info in Chinese and Japanese show garbled code under Human Interface Infrastructure (HII) Form


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2
changelog:
  -     *Problems Fixed:**
      
        * This firmware contains fixes to prevent incorrect data from potentially occurring.  Failures have not been reported by a customer but were found in a lab testing environment.  Exposure is limited due to a narrow window of opportunity following a hard reset or when two consecutive write faults occur causing an error in the Input/Output Data Error Detection & Correction scheme.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4
changelog:
  -     *Problems Fixed:**
      
        * This firmware improves HDD reliability when HDDs are exposed to long periods of host inactivity that exceed 1 second. HDDs may become unresponsive when using HDD firmware prior to version HPD4.  This firmware also contains a change which prevents an incorrect reassign status of a repaired sector from being logged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4-2.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager.**
        * ****Customers who already installed firmware version HPD4 do not need to update to HPD4 (B).****


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4-2.1
changelog:
  -     *Enhancements/New Features for HPD4 (B):**
      
        * Adds support for HPE ProLiant Gen10 servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4-3.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPD4 do not need to update to HPD4(c).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.72
changelog:
  -     *The following fix is added in this version:-**
      
        * Fixed an issue causing fan speed to run at the maximum level due to a false error indication reported on early production hardware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.72-3.1
changelog:
  -     Firmware upgrade to 1.72(C) is not necessary, if the device is currently
      running 1.72 firmware


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.72-3.1
changelog:
  -     *The following fix is added in this version:-**
      
      -Fixed an issue causing fan speed to run at the maximum level due to a false error indication reported on early production hardware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 3.64
changelog:
  -     *The following enhancement was incorporated in this version:**
      
        * Added support for 3610 and 3710 disk enclosures


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.04-1.1
changelog:
  -     *The following fix was incorporated in this version:**
      
        *  Fixed NVRAM CRC error
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p879663226/v148867/D3000_P07231-001.html) for the complete listing of
      fixes, enhancements, known issues and work-arounds corresponding to this
      firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.04-2.1
changelog:
  -     *The following fix was incorporated in this version:**
      
        *  Fixed NVRAM CRC error
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p879663226/v155369/D3000_P07231-002.html) for the complete listing of
      fixes, enhancements, known issues and work-arounds corresponding to this
      firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.04-3.1
changelog:
  -     *The following fix was incorporated in this version:**
      
        *  Fixed NVRAM CRC error
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p879663226/v157942/P07231-003.html) for the complete listing of fixes,
      enhancements, known issues and work-arounds corresponding to this firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.12
changelog:
  -     *The following fixes were incorporated in this version:**
      
        * Fixed TLB exception during upgrade from Rev build 1.11.000 to 0412.000
      
        * Fixed expander bootstrap task which failed with 0xB1 error code appearing in the console due to missing NVRAM tag - Product Name
      
        * Enabled-ClusterS2D command that does not complete with SATA drive in D3610
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p879663226/v154196/D3000_P07231-004.html) for the complete listing of
      fixes, enhancements, known issues and work-arounds corresponding to this
      firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3
changelog:
  -      Removes a vendor unique sense code that the controller does not handle properly.
        * Includes changes to eliminate the cause of a potential hang condition.
        * Changes some settings to comply with Microsoft Storage Spaces Certification requirements.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.09-1.1
changelog:
  -     *The following fix is added in this version:**
      
        * Failed to set the power supply fail flag when power supply status was critical
        * General exception message appeared on the console
        * D6020 Disk Enclosure - Segments of node3 & node4 of 6500-6600 Mixed Cluster going into"NotAvailable" or "OnBackup" State
        * Remove SysIndicators references from ESP


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.53
changelog:
  -     *The following fix is added in this version:**
      
        * Enclosure in Unexpected status: Non-critical after restoring the Encl ID.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.72
changelog:
  -     *The following fixes was incorporated in this version:**
      
        * Sensors presence reporting for single domain mode
        * When an IOM is pulled the surviving IOM reports False critical temperatures
        * Configure phy zone group to 0 (zero) for all phys in the initstring
      
      Please refer to the [Release
      Notes](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p1194926978/v148868/D6020_P07232-001.html) for the complete listing of
      fixes, enhancements, known issues and work-arounds corresponding to this
      firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.74
changelog:
  -     *The following fixes were incorporated in this version:**
      
        * Temperature sensors logic inside gSEP model and SES database
        * When an IOM is pulled the surviving IOM reports false critical temperatures
      
      Please refer to the [Release
      Notes](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p1194926978/v154195/D6020_P07232-002.html) for the complete listing of
      fixes, enhancements, known issues and work-arounds corresponding to this
      firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.74-1.1
changelog:
  -     *The following fixes were incorporated in this version:**
      
        * Temperature sensors logic inside gSEP model and SES database
        * When an IOM is pulled the surviving IOM reports false critical temperatures
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p1194926978/v157943/P07232-003.html) for the complete listing of fixes,
      enhancements, known issues and work-arounds corresponding to this firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.74-2.1
changelog:
  -     *The following fixes were incorporated in this version:**
      
        * Temperature sensors logic inside gSEP model and SES database
        * When an IOM is pulled the surviving IOM reports false critical temperatures
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p1194926978/v160758/D6020_P07232-004.html) for the complete listing of
      fixes, enhancements, known issues and work-arounds corresponding to this
      firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD1
changelog:
  -     *Enhancements/New Features:**
      
        * Reliability enhancement for applications that write data to a narrow range of tracks.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3
changelog:
  -     *Enhancements/New Features:**
      
        * Adds support for HPE ProLiant Gen10 servers.
        * Improved write performance.
      
        * A reliability enhancement for applications that write data to a narrow range of tracks


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4-2.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager**
        * **Customers who already installed firmware version HPD4 do not need to update to HPD4(B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2017.09.01
changelog:
  -     We  have separate components to update fibre channel and converged network
      adapters. This is a fibre channel update component.  
        
      Updated 16 Gb HBA/Mezz universal boot.  
      Updated 32 Gb HBA universal boot  
      Updated 8Gb HBA/Mezz boot bios.  
        
      Contains:  
        
      16 Gb HBA/Mezz universal boot 11.2.307.16  
      16/32 Gb HBA universal boot 11.2.307.16  
        
      8 Gb Gen8 Mezz (LPe1205A) firmware 2.03X14  
      8 Gb  standup firmware 2.03x14  
      8 Gb Mezz firmware 2.03x14  
      8 Gb HBA/Mezz boot image 11.20A7 (11.2.241.0 BIOS, 11.2.283.0 UEFI)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2017.09.01
changelog:
  -     8G Firmware:
      
      Fixed the following:
      
        * Link down encountered during high traffic on 81E, 82E, 84E, LPe1205a
      
      UEFI:
      
        * Boot Device Order menu not displaying targets on HPE servers
      
      
      
      16G Firmware:
      
      Fixed the following:
      
        * Incorrect adapter showed up in PCI slot 1 in Dashboard and Static Networking
      
      
      
      16G/32G Firmware:
      
      Fixed the following:
      
        * Incorrect adapter showed up in PCI slot 1 in Dashboard and Static Networking


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2018.02.01
changelog:
  -     We  have separate components to update fibre channel and converged network
      adapters. This is a fibre channel update component.
      
      Added support to the following:
      
      8G Standup and Mezzanine:
      
      BIOS:
      
        * Add support for Direct attach Point to Point
      
      16 Gb Standup, 16 Gb Mezzanine & 32G Standup:
      
      UEFI:
      
        * V2.40 Unified Extensible Firmware Interface (UEFI) driver support for HP Servers
      
      BIOS/Firmware:
      
        * Enable Buffer to Buffer credit (BB_credit) recovery using the Fibre Channel (FC) primitives
        * Platform Level Data Model (PLDM)/Management Component Transport Protocol (MCTP) Standard Firmware Download
        * Support for Bi-Directional D-port & Clearlink
        * Security Enhancements
      
      Updated 16/32 Gb HBA/Mezz universal boot  
      Updated 16Gb  HBA/Mezz universal boot  
      Updated 8Gb  HBA/Mezz universal boot
      
      **Contains:**
      
      16/32 Gb HBA/Mezz universal boot 11.4.225.21  
      16 Gb HBA/Mezz universal boot 11.4.225.21
      
      8 Gb standup/mezz firmware 2.03x14
      
      8 Gb standup/mezz universal boot image 11.40a9 (11.4.231.0 BIOS, 11.4.260.0
      UEFI)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2018.06.01
changelog:
  -     We  have separate components to update fibre channel and converged network
      adapters. This is a fibre channel update component.
      
      Added support to the following:
      
      8G Standup and Mezzanine:
      
      BIOS:
      
        * Fabric assigned Boot Target/Logical Unit (LUN) to Fabric Assgined World Wide Name(FAWWN)
      
      Updated 16/32 Gb HBA/Mezz universal boot  
      Updated 16Gb  HBA/Mezz universal boot  
      Updated 8Gb  HBA/Mezz universal boot
      
      **Contains:**
      
      16/32 Gb HBA/Mezz universal boot 11.4.334.10  
      16 Gb HBA/Mezz universal boot 11.4.334.11
      
      8 Gb standup/mezz firmware 2.10X6
      
      8 Gb standup/mezz universal boot image 11.40a13 (11.4.305.0 BIOS, 11.4.344.0
      UEFI)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2018.09.01
changelog:
  -     We  have separate components to update fibre channel and converged network
      adapters. This is a fibre channel update component.
      
      Added support to the following:
      
      8G Standup and Mezzanine:
      
      BIOS:
      
        * Fabric assigned Boot Target/Logical Unit (LUN) to Fabric Assgined World Wide Name(FAWWN)
      
      Updated 16/32 Gb HBA/Mezz universal boot  
      Updated 16Gb  HBA/Mezz universal boot  
      Updated 8Gb  HBA/Mezz universal boot
      
      **Contains:**
      
      16/32 Gb HBA/Mezz universal boot 11.4.334.10  
      16 Gb HBA/Mezz universal boot 11.4.334.27
      
      8 Gb standup/mezz firmware 2.10X6
      
      8 Gb standup/mezz universal boot image 11.40a13 (11.4.305.0 BIOS, 11.4.344.0
      UEFI)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2018.09.02
changelog:
  -     We  have separate components to update fibre channel and converged network
      adapters. This is a fibre channel update component.
      
      Added support to the following:
      
      8G Standup and Mezzanine:
      
      BIOS:
      
        * Fabric assigned Boot Target/Logical Unit (LUN) to Fabric Assgined World Wide Name(FAWWN)
      
      Updated 16/32 Gb HBA/Mezz universal boot  
      Updated 16Gb  HBA/Mezz universal boot  
      Updated 8Gb  HBA/Mezz universal boot
      
      **Contains:**
      
      16/32 Gb HBA/Mezz universal boot 11.4.334.10  
      16 Gb HBA/Mezz universal boot 11.4.334.31
      
      8 Gb standup/mezz firmware 2.10X6
      
      8 Gb standup/mezz universal boot image 11.40a13 (11.4.305.0 BIOS, 11.4.344.0
      UEFI)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2018.09.02
changelog:
  -     Fixed the following:
      
        * Fixed an issue where OneView profile data is lost during firmware upgrades from versions earlier than 11.4.x.x


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2018.09.03
changelog:
  -     Fixed the following:
      
        * Entries in payload.json which was triggering firmware discovery and flash to be incomplete on HPE SN1200E 16Gb 1port/2port adapter when firmware flash was attempted via OneView, integrated Lights Out(iLO) and UEFI flash mode.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3
changelog:
  -      Fix to the error recovery algorithm to improve the overall reliability of the device.
        * Fix to insure complete support of internal logging during a sudden power off event which prevents the device entering into a degraded state.
        * Fixed a mishandling of error handling data during back ground media activities prevent a data issue.
        * Fix to  correct a buffer management timing issue internal to the device allowing for a more robust internal movement of data.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2017.06.01
changelog:
  -     *8Gb Standup & 8Gb Mezzanine**
      
      BIOS
      
        * Maintenance updates
      
      UEFI
      
        * Fixed unexpected behavior during Win2012 boot on 3PAR storage array
      
      
      
      **16Gb Standup & 16Gb Mezzanine**
      
      BIOS
      
        * Added code to allow direct connected LUN to be configured when FA_BLUN is enabled.
      
        * Fixed unexpected behavior in check_mem64 routine where pci address was not setup correctly.
      
        * Fixed bug that caused FlexAddress to stop
      
      UEFI
      
        * Fixed HII Load Defaults issue onHP QMH2672 16Gb Fibre Channel Host Bus Adapter . HII Load defaults no longer adds items to the Adapter Settings menu
      
        * Fixed unexpected behavior during Win2012 boot on 3PAR storage array


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2017.09.01
changelog:
  -     Updated the Firmware/BIOS/UEFI packages for 8 Gb, 16 Gb and 32 Gb products.
      
        * 8 Gb HBA/Mezz 
          * Package 3.76.06
          * Firmware 8.05.00
          * UEFI 6.52
          * BIOS 3.56  
      
      
        * 16 Gb HBA/Mezz 
          * Package 6.01.41
          * Firmware 8.05.63
          * UEFI 6.54
          * BIOS 3.43  
      
      
        * 16/32 Gb 
          * Package 01.70.51
          * Firmware 8.05.61
          * UEFI 6.36
          * BIOS 3.54


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2017.09.01
changelog:
  -     8Gb Standup & 8Gb Mezzanine
      
      BIOS
      
        * Incorrect processing of Command Line Processor (CLP)  'set netport'
        * Improper display of Command Line Processor (CLP) Logical Unit Number (LUN)
      
      UEFI
      
        * Changed Operation Mode Human Interface Infrastructure (HII) strings. The new strings match the FastUTIL strings.
        * Self-certification Test (SCT) 2.4B BlockIO2 Protocol bug.
        * No response during Self-certification Test (SCT) 2.4B BlockIO2 Protocol test.
        * Self-certification Test (SCT) 2.4B AdapterInfo Protocol bugs.
      
      
      
      16Gb Standup & 16Gb Mezzanine
      
      UEFI
      
        * Adapter not appearing in Health Summary page.
        * Invalid Health message when link was down or driver was disabled.
        * Adapter connection mode to change (OS install related) when the Human Interface Infrastructure (HII) Link Speed field changed.
      
      
      
      32Gb Standup & 16Gb Mezzanine
      
      UEFI
      
        * Adapter not appearing in Health Summary page.
        * Invalid Health message when link was down or driver was disabled.
        * Added code to start operational firmware early.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2018.02.01
changelog:
  -     Added support for the following:
      
      **8Gb Standup & 8Gb Mezzanine**
      
        * Additional "show Command Line Processor (CLP's)".
        * Gen10 Driver Health error codes.
      
      **16Gb Standup & 16Gb Mezzanine**
      
        * Gen10 Driver Health error codes
        * OEMHP_TargetBootPaths Command Line Processor (CLP) command.
      
      **16Gb/32Gb Standup **
      
        * Gen10 Driver Health error codes.
        * OEMHP_TargetBootPaths Command Line Processor (CLP) command.
        * Semaphore checks before flash reads and writes
      
      Updated the Firmware/BIOS/UEFI packages for 8 Gb, 16 Gb and 32 Gb products.
      
        * 8 Gb HBA/Mezz 
          * Package 3.77.03
          * Firmware 8.05.00
          * UEFI 6.59
          * BIOS 3.56  
      
      
        * 16 Gb HBA/Mezz 
          * Package 6.01.50
          * Firmware 8.05.64
          * UEFI 6.58
          * BIOS 3.43  
      
      
        * 16/32 Gb 
          * Package 01.70.66
          * Firmware 8.05.65
          * UEFI 6.41
          * BIOS 3.54


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2018.02.01
changelog:
  -     Fixed the following:
      
      **8Gb Standup & 8Gb Mezzanine**
      
      BIOS
      
        *  CTRL-Q cosmetic unexpected behavior
      
      UEFI
      
        *  Simple Control Transmission (SCT) 2.5 Extended Small Computer System Interface (SCSI) Pass Thru Protocol test incompleteness. PassThru_Func test no longer goes incomplete.
        *  Operating System (OS) boot incomplete behavior when Read Only Memory (ROM) Based Setup-Utility (RBSU) Power On Self -Test (POST) Discovery Mode was set to Force Fast Discovery
        *  Human Interface Infrastructure (HII) save unexpected behavior on Superdome servers. In the World Wide Name (WWN) Database menu, changes to Drive0 and Drive1 are now saved to Non  Volatile Random Access Memory (NVRAM)
        *  Unexpected behavior which caused adapter to not appear on the Health Summary page.
        *  Operating System (OS) boot incomplete behavior when Read Only Memory (ROM) Based Setup-Utility (RBSU) Power On Self -Test (POST) Discovery Mode was set to Auto
        *  World Login unexpected behavior when Power On Self -Test (POST) Discovery Mode was set to Auto
      
      
      
      **16Gb Standup & 16Gb Mezzanine**
      
      UEFI
      
        *  Simple Control Transmission (SCT) 2.5 Extended Small Computer System Interface (SCSI) Pass Thru Protocol test incompleteness. PassThru_Func test no longer goes incomplete
      
      
      
      **16Gb/32Gb Standup**
      
      UEFI
      
        *  Human Interface Infrastructure (HII) save unexpected behavior. In the World Wide Name (WWN) Database menu, changes to Drive0 and Drive1 are now saved to Non Volatile Random Access Memory (NVRAM).
        *  Corrected adapter name format in Read Only Memory (ROM) Based Setup-Utility (RBSU) menus.
        *  Unexpected behavior that caused Non Volatile Random Access Memory (NVRAM) overwritten after Human Interface Infrastructure (HII) changes
        *  Behavior that caused Human Interface Infrastructure (HII) fields to not revert back to original settings when ESC key was used to discard changes


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2018.06.01
changelog:
  -     Added support for the following:
      
      **16Gb Standup & 16Gb Mezzanine**
      
        * Power Loss calculation in D_port (Destination port) operation.
      
      **16Gb/32Gb Standup **
      
        * Power Loss calculation in D_port (Destination port) operation.
        * Support maximum training timeout for 32Gbps data rate per FC-FS-4 (Fibre Channel Framing and Signaling) specification.
      
      Updated the Firmware/BIOS/UEFI packages for 8 Gb, 16 Gb and 32 Gb products.
      
        * 8 Gb HBA/Mezz 
          * Package 3.77.08
          * Firmware 8.07.00
          * UEFI 6.64
          * BIOS 3.56  
      
      
        * 16 Gb HBA/Mezz 
          * Package 6.01.59
          * Firmware 8.07.16
          * UEFI 6.63
          * BIOS 3.43  
      
      
        * 16/32 Gb 
          * Package 01.70.85
          * Firmware 8.07.18
          * UEFI 6.47
          * BIOS 3.54


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2018.06.01
changelog:
  -     Fixed the following
      
      **8Gb Standup & 8Gb Mezzanine**
      
      UEFI
      
        * Firmware Management Protocol now supports flashing older Multiboot versions.
        * Firmware Management Protocol SetImage no longer displays dots on the screen.
        * The following HII (Human Interface Infrastructure) fields now require a reboot after value change:  
      Legacy BIOS (Basic Input Output System) Selectable Boot
      
      
      
      **16Gb Standup & 16Gb Mezzanine**
      
      Firmware
      
        * Bring up up-link in 32G or 16G optical environment (FEC (Forward Error Correction) only) when connected with remote device that is not setting the SN bit to zero and TC bit to 1 at the same time during the speed negotiation phase and delays transmitting NOS during LQT phase.
        * Dropped FCP_CMD frame by a virtual port (VP index greater than 0) logged into the fabric via Fabric Login (FLOGI) while the primary adapter port (VP0) was disabled via Global VP (Virtual Port) Options bit 2 of Initialize Multi-ID Firmware MBC (0048h).
      
      UEFI
      
        * Firmware Management Protocol now supports flashing older Multiboot versions.
        * Firmware Management Protocol SetImage no longer displays dots on the screen.
        * The following HII (Human Interface Infrastructure) fields now require a reboot after value change:  
      Fabric Assigned WWPN (World Wide Port Name), Fabric Assigned Boot Logical Unit
      (LUN), Legacy BIOS (Basic Input Output System) Selectable Boot.
      
      
      
      **16Gb/32Gb Standup**
      
      Firmware
      
        * Bring up up-link in 32G or 16G optical environment (FEC (Forward Error Correction) only) when connected with remote device that is not setting the SN bit to zero and TC bit to 1 at the same time during the speed negotiation phase and delays transmitting NOS during LQT phase.
      
      UEFI
      
        * Firmware Management Protocol now supports flashing older Multiboot versions.
        * Firmware Management Protocol SetImage no longer displays dots on the screen.
        * The following HII (Human Interface Infrastructure)  fields now require a reboot after value change:  
      FC (Fibre Channel) Tape, Fabric Assigned WWPN (World Wide Port Name), Fabric
      Assigned Boot LUN (Logical Unit), Legacy BIOS (Basic Input Output System)
      Selectable Boot.
      
        * Changed Legacy BIOS (Basic Input Output System) Selectable Boot HII (Human Interface Infrastructure) default to Enabled.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2019.03.01
changelog:
  -     Fixed the following
      
      **8Gb Standup & 8Gb Mezzanine**
      
      Firmware:
      
        * Fix regression where the firmware returned Time Out error code under heavy load.
      
      UEFI
      
        * Driver progress messages are no longer displayed on SuperDome servers.
        * Corrected Driver Health string format on Gen10 servers
      
      **16Gb Standup & 16Gb Mezzanine**
      
      Firmware:
      
        * Fix unexpected behavior related to Diagnostic Port and Link Diagnostics operations (loopback, echo etc)
      
      UEFI:
      
        * Driver progress messages are no longer displayed on SuperDome servers.
        * Corrected Driver Health string format on Gen10 servers.
      
        
      **16Gb/32Gb Standup**
      
      Firmware:
      
        * Fix unexpected behavior related to Diagnostic Port and Link Diagnostics operations (loopback, echo etc)
      
      UEFI:
      
        * Corrected Driver Health string format on Gen10 servers.
        * Driver progress messages are no longer displayed on SuperDome servers.
        * Fixed QUIC (QUIC Protocol)
        * Removed 8G Speed and Loop Only Options from 5830C Adapter


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3-2.1
changelog:
  -     *Enhancements/New Features:**
      
        * Firmware version HPD3 supports NDU (non-disruptive update) firmware updates.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3-3.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPD3 do not need to update to HPD3(C).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.3
changelog:
  -     *Firmware for the following devices are updated to 10.10.5052:**  
        
      702211-B21  
      702212-B21  
      702213-B21


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.3
changelog:
  -     *Fixes:**
      
        * Fixed improper handling of sequential connect packets.
        * On rare occasions, after PXE boot, the port speed came up as SDR instead of a higher speed.
        * On very rare occasions, a false alarm thermal indication was reported when HP mezz cards were rebooted.
        * On very rare occasions, firmware wrongly reported board over-temperature warning.
        * destroy-DCT command handling may experience delays while the DCT port is down.
        * Fixed an issue causing diagnostic counters VS-MAD page offset to start at a wrong address.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4
changelog:
  -     *Firmware for the following devices are updated to 10.10.5052:**  
        
      702211-B21 (HP Infiniband FDR 2P 545QSFP Adapter)  
      702212-B21 (HP Infiniband FDR 2P 545FLR-QSFP Adapter)  
      702213-B21 (HP Infiniband FDR 2P 545M Adapter)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.5-2.1
changelog:
  -     *Firmware for the following devices are updated to 10.16.1006:**  
        
      702211-B21 (HP Infiniband FDR 2P 545QSFP Adapter)  
      702212-B21 (HP Infiniband FDR 2P 545FLR-QSFP Adapter)  
      702213-B21 (HP Infiniband FDR 2P 545M Adapter)
      
      **New features in firmware version 10.16.1006:**
      
        * Increased the number of VFs from 32 to 64 per PF.
        * Keeps track of the creation of a packet. A time-stamping service supports assertions of proof that a datum existed before a particular time.
        * Custom port counters provide the user a clear indication about RDMA send/receive statistics and errors.
        * The change includes the following: 
          * Changed port configuration which required link re-training (such as speed)
          * PAOS down/up
          * This change, will cause the link to toggle and new configurations to take effect.
        * Flint utility allows performing an MD5 checksum on the non-persistent sections of the firmware image.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.5-2.1
changelog:
  -     *The following issues are fixed in firmware version 10.16.1006:**
      
        * Fixed an issue causing single port devices to query and write Physical Port TLVs to Port 2.
        * Fixed an issue which caused the device to hang when resetting qkey/pkey violation counter via port_info mad.
        * Improved RDMA READ bandwidth under packet lost scenario.
        * If the PF driver or the tool (e.g. ethtool) use PAOS DOWN command (e.g. by ifconfig down or ip link set down), loopback traffic is blocked for all functions on this port (PF<->VFs / VF<->VF)  
      In Multihost loopback, the traffic will be blocked once the firmware receives
      the PAOS down command from all PFs. However, the loopback traffic will not be
      blocked when the port is down due to the physical link (for example: cable
      plugged out, switch port down).
      
        * Fixed an issue which prevented QP permission for reserve lkey to be passed to the memop machine.
        * Fixed a MLX QP SL mismatch handling which 10.12.0780 occurred when the SL in the WQE was different than the SL in the QP.
        * Fixed wrongly implementation of SM SL2VL configuration.
        * Fixed a DC re-connect flow which in some cases 10.12.0780 sent bad completion.
        * Fixed a DC performance issue; separated DCRs 10.12.0780 SQ from the DCI SQs.
        * Fixed an issue causing the firmware to hang 10.12.0780 when running ibdiagnet. The received DiagData  
      MAD included the following values:  
       Clear_all = 1  
       PageNum = 0  
       Port_select = 0  
      To prevent the firmware from hanging, a port check was added to Set() as well.
      
        * Hardware fatal error used to occur when running "ibdump".
        * FDR10 incorrect speed indication was reported due to the usage of a translation function from the hardware speed to the PRM speed twice.
        * Invalid data was returned by EyeOpening MAD.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.5-3.1
changelog:
  -     *Firmware for the following devices are updated to 10.14.1100:**  
        
      702211-B21 (HP Infiniband FDR 2P 545QSFP Adapter)  
      702212-B21 (HP Infiniband FDR 2P 545FLR-QSFP Adapter)
      
      **Firmware for the following devices are updated to 10.16.1038:**
      
      702213-B21 (HP Infiniband FDR 2P 545M Adapter)
      
      **New features in firmware version 10.14.1100:**
      
        * Keeps track of the creation of a packet. A time-stamping service supports assertions of proof that a datum existed before a particular time.
        * Custom port counters provide the user a clear indication about RDMA send/receive statistics and errors.
        * The change includes the following: 
          * Changed port configuration which required link re-training (such as speed)
          * PAOS down/up
          * This change, will cause the link to toggle and new configurations to take effect.
        * Flint utility allows performing an MD5 checksum on the non-persistent sections of the firmware image.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.5-3.1
changelog:
  -     *The following issues are fixed in firmware version 10.16.1038****:**
      
        * Fixed RSOD bug.
      
      **The following issues are fixed in firmware version 10.14.1100:**
      
        * Fixed an issue which prevented QP permission for reserve lkey to be passed to the memop machine.
        * Fixed a MLX QP SL mismatch handling which 10.12.0780 occurred when the SL in the WQE was different than the SL in the QP.
        * Fixed wrongly implementation of SM SL2VL configuration.
        * Fixed a DC re-connect flow which in some cases 10.12.0780 sent bad completion.
        * Fixed a DC performance issue; separated DCRs 10.12.0780 SQ from the DCI SQs.
        * Fixed an issue causing the firmware to hang 10.12.0780 when running ibdiagnet. The received DiagData  
      MAD included the following values:  
       Clear_all = 1  
       PageNum = 0  
       Port_select = 0  
      To prevent the firmware from hanging, a port check was added to Set() as well.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.6
changelog:
  -     *The following issues are fixed in firmware version 10.16.1058****:**
      
        * Fixed an issue which caused system fail when enabled SR-IOV.
        * Fixed a rare issue which caused the RX to hang when triggered the SRQ limit event.
        * Fixed an issue which occasionally caused the RX traffic to hang in DC when received a PCI error on WQE fetch.
        * Fixed an issue which caused the mlxconfig configuration of VF_LOG_BAR_SIZE to be ignored and to be set to 5 (32MB).
        * Fixed an EEH error from PCI which caused firmware to hang.
        * Fixed an issues which occasionally caused the driver to hang during unload on some VLs when configuring the SM with a VL weight 0 and running traffic on it.
        * Fixed a rare case which caused an assert reported to the driver when the DC transport was enabled in the following cases: retransmission occurred and the RX received the same packet twice
        * Fixed an issue which caused the HCA to hang when enabled /disabled the VFs vports when the VFs GUIDs configuration were overloaded in the steering table.
      
      **The following issues are fixed in firmware version 10.16.1038****:**
      
        * Fixed RSOD bug.
        * Fixed an issue causing single port devices to query and write Physical Port TLVs to Port 2.
        * Fixed an issue which caused the device to hang when resetting qkey/pkey violation counter via port_info mad.
        * Improved RDMA READ bandwidth under packet lost scenario.
        * If the PF driver or the tool (e.g. ethtool) use PAOS DOWN command (e.g. by ifconfig down or ip link set down), loopback traffic is blocked for all functions on this port (PF<->VFs / VF<->VF)  
      In Multihost loopback, the traffic will be blocked once the firmware receives
      the PAOS down command from all PFs. However, the loopback traffic will not be
      blocked when the port is down due to the physical link (for example: cable
      plugged out, switch port down).
      
        * Fixed an issue which prevented QP permission for reserve lkey to be passed to the memop machine.
        * Fixed a MLX QP SL mismatch handling which occurred when the SL in the WQE was different than the SL in the QP.
        * Fixed wrongly implementation of SM SL2VL configuration.
        * Fixed a DC re-connect flow which in some cases sent bad completion.
        * Fixed a DC performance issue; separated DCRs SQ from the DCI SQs.
        * Fixed an issue causing the firmware to hang when running ibdiagnet. The received DiagData MAD included the following values:  
       Clear_all = 1  
       PageNum = 0  
       Port_select = 0  
      To prevent the firmware from hanging, a port check was added to Set() as well.
      
        * Fixed an issue which caused hardware fatal error when running ibdump.
        * Fixed an FDR10 incorrect speed indication reported due to the usage of a translation function from the hardware speed to the PRM speed twice.
        * Fixed a Phy manager PCS event handling when the port's next state was disable.
        * Fixed an issue that caused invalid data returned by EyeOpening MAD.
        * Reduced the VF ICM footprint for VFs.
        * Increased the number of regular memory region from 2^21 to 2^22.
        * Fixed improper handling of sequential connect packets.
        * On rare occasions, after PXE boot, the port speed came up as SDR instead of a higher speed.
        * On very rare occasions, firmware wrongly reported board over-temperature warning.
        * destroy-DCT command handling may experience delays while the DCT port is down.
        * Fixed an issue causing diagnostic counters VS-MAD page offset to start at a wrong address.
        * Fixed stability issue in the event of no-local-DC-resources.
        * Fixed improper handling of multiple DCT errors.
        * Fixed bad handling of DC RNR state.
        * Reduced DCT destroy firmware handling time.
        * Fixed link flapping issue which occurred when LLR was active.
        * Deprecated code 0x0c0600 was changed to 0x020700 (InfiniBand network adapter).
        * Atomic response endianess is always a big endian.
        * **[Documentation fix in PRM v2.01, no changes to the firmware code.]**  
      Port asynchronous events documentation are different from the PRM. All port
      events have a type value of 0x9.  
      The following subtype values are used for the following events:  
       link down=0x1  
       link up=0x4  
       link initialized=0x5  
       lid change=0x6  
       PKEY change=0x7  
       GUID change=0x8  
       client reregister=0x9
      
        * Alternate Path Migration (APM) triggers only a single affiliated asynchronous error event in the case of a path migration failure.
        * Using a min_rnr_nak value of 0x5 will cause failures when creating reliable connection (RC) QPs.
        * On rare occasions DC Initiator completions might be lost.
        * The following signature rules are not supported (Numbering based on "signature rules table" in PRM):  
       Rule #12: T10 DIF  
       Rule #13: T10 DIF CS  
       Rule #14 T10 DIF CS
      
        * VL arbitration configuration does not ensure minimum bandwidth for VL as configured.
        * On very rare occasions, a false firmware "hanged" report is printed in the dmesg.
        * CQ buffer resize not supported.
        * When connecting to InfiniScale family switches and non-Mellanox InfiniBand switches DDR and QDR speeds may show line errors and in some cases might downgrade to SDR speed.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.0-2.1
changelog:
  -     *Fixes in FW version 12.16.1010:**
      
        * Added legacy interrupts support in FlexBoot.
        * Modified the TX configuration to support EMI crossing margins in 16Ghz.
        * Fixed an issue which prevented MAC address changes by to driver to be reflected in the OBCC and NC-SI interfaces.
        * In some cases, a Bit Error Rate is not optimal on 10G/40G links.
        * Instability of Link Training Flow occurs during 100G Auto-Negotiation.
        * Fixed a rare issue which caused the command to hang when moved the QP to RESET and back to RTS.
        * Added support for pnat = 1 in HCA access_reg command as required by the ibdiagnet tool.
        * Fixed the LLDP OCBB response: return value is now ascii.
        * Increased the steering hash tables static size from 128 to a maximum of 32K entries.
        * Prevented miscalculation of module temperature when using 100Gb/s cables (OPN: MFA1A00-Cxxx for 100GbE).
        * Fixed an issue which caused the device to hang when resetting qkey/pkey violation counter via port_info mad.
        * Changed the MTU size in OCBB report. Now MTU size does not include the packet headers.
        * Reduced one hop for Unicast RX steering, steering pipes balancing.
        * Non-volatile configuration of Port Type TLV more than 50 times might cause system hang.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.0-3.1
changelog:
  -     *Firmware Version 12.16.1038:**
      
      825110-B21 HPE InfiniBand EDR/Ethernet 100Gb 1-port 840QSFP28 Adapter
      
      825111-B21 HPE InfiniBand EDR/Ethernet 100Gb 2-port 840QSFP28 Adapter


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.1
changelog:
  -     *Firmware Version 12.18.2030:**
      
      825110-B21 (HPE InfiniBand EDR/Ethernet 100Gb 1-port 840QSFP28 Adapter)
      
      825111-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 840QSFP28 Adapter)
      
      **New features and changes in version 12.18.2030:**
      
        * Added logical link indication in SFP to BaseT modules and disabled logical link when peer port is down.
        * Added support for 10GbE in 25GbE SFP optical modules.
        * Enables mlxlink tool to collect data on the PHY link status and provides link down reasons and additional link related information.
        * Enabled TX configuration response and movement during Link Training in Ethernet.
        * Added support at lane rate of 12.89Gb.
        * Limits the amount of time a packet may head a Traffic Class (TC) transmission queue, without being transmitted. Stale packets are discarded. Active by default for TCs adhering to link level flow control.
        * UAR page size currently is set to 4KB and not according to what the system page size determines.
        * Improved performance of:  
       Doorbell from User Access Region (UAR)  
       Clear interrupt from User Access Region (UAR)
      
        * Added support for additional transport counters.
        * Added ODP support for DC.
        * Enabled scatter-to-CQE for sent packets for DC.
        * Enabled moderation period modification in CQ modify command.
        * Added support for minimum/maximum rate limit per vport in SR-IOV.
        * Enabled network traffic between UEFI-Shell and OS.
        * Enabled the PF to force disable RoCE for its VFs.
        * Added 2 new access registers:  
       Management Capabilities Mask Register  
       Ports CApabilities Mask Register Fields  
      For further information, please refer to the PRM.
      
        * Enabled VNIC the control to enable/disable its local loopback traffic.
        * Added the option to open a receive RDMA Flow Table and to forward RoCE traffic to some destination QP.
        * Added support for Multi-Host LID base routing. This feature requires a new OpenSM (v4.7.1 and above which comes with MLNX_OFED 3.3-2.0.0.0) with the following attributes:  
       qos TRUE  
       lmc 2 (if there is no quad host in the fabric, you can set the lmc to 1)  
       virt_enabled 2 Note: Multi-Host LID base routing can be configured by the
      INI only. The default is 0
      
        * Resilient RoCE is the ability to send RoCE traffic over a lossy network (a network without flow control enabled), without the need to enable flow control on the network. The ability is accomplished by enabling ECN on both the Switch and the Host.
        * Enables load balancing in the Multi PF Switch layer (MPFS) based on the L3/L4 headers.
        * Enabled isolation between separate Hosts using the same HCA. All the Hosts can be rebooted, the driver can be stopped and the FLR signal can be sent independently.
        * Increased the number of VFs from 64 to 95 per Physical Function (PF). Note: When increasing the number of VFs, the following limitations must be taken into consideration: server_total_bar_size >= (num_pfs)*(2log_pf_uar_bar_- size + 2log_vf_uar_bar_size*total_vfs) server_total_msix >= (num_pfs)*(num_pf_msix + num_vfs_msix *total_vfs) Note: For the maximum number of VFs supported by your driver, please refer to your drivers' Release Notes or User Manual.
        * [InfiniBand Only] Added support for multiple VLs in SR-IOV/mutlihost environments. Note: The number of VLs can be configured by the NVCONFIG. The default VL number is 4 VLs.
        * Added support for QP Rate Limit in InfiniBand.
        * Added support for Port Flap Counter.
        * Limits the buffer size for all entries to improve performance. KSM is used when associating Key Length My Virtual Address (KLMs) with fixed memory size.
        * This entry (null_mkey) is use to indicate non-present KLM/KSM entries. When accessing is, it causes the device to generate page fault event.
        * PLDM firmware burning is based on the DMTF spec DSP0267 (draft 9). The feature enables upgrading firmware and expansion ROM images using the PLDM protocol over MCTP (over PCIe). By doing so, a supporting BMC can query and upgrade the firmware without using OS based tools.
        * Added a new physical layer statistics counters group. The new group includes BER counters, FEC error correction, clear time, and additional physical layer counters. For further information, please refer to the Ethernet Adapters Programming Manual (PRM).
        * Enables the user to set a certain link up state for an unlimited period of time. This mode has 3 states:  
       Aux power (standby)  
       Reboot/boot/driver unloaded - the server is active and no driver is up  
       Driver is up - at least one driver is up (the time between init HCA and
      teardown or FLR)
      
        * Added support for Doorbell from User Access Region (UAR).
        * [Beta] Added support for maximum rate limit per function in SR-IOV.
        * Allows the user to configure the adapter card to stop sending pauses after x when the receive port is unavailable (in a hang state).
        * [Beta] Added support for new performance counters.
        * DCBX is used by DCB devices to exchange configuration information with directly connected peers. DCBX uses Link Layer Discovery Protocol (LLDP) to exchange parameters between two link peers. For further information, please refer to the PRM.
        * Allows network port registers to revert to their default values when the driver is restarted or the host is rebooted.
        * Added additional network link up modes. The new modes decide when to keep the network link up. The new modes are:  
       keep_eth_link_up  
       keep_ib_link_up  
       keep_link_up_on_boot  
       keep_link_up_on_standby
      
        * [Beta] Explicit Congestion Notification (ECN) is an extension to the Internet Protocol and to the Transmission Control Protocol. ECN allows end-to-end notification of network congestion without dropping packets.
        * Increased the number of VFs from 32 to 64 per PF. Note: When increasing the number of VFs, the following limitations must be taken into consideration: server_total_bar_size >= (num_pfs)*(2log_pf_uar_bar_- size + 2log_vf_uar_bar_size*total_vfs) server_total_msix >= (num_pfs)*(num_pf_msix + num_vfs_msix *total_vfs)
        * [Beta] RoCE Link Aggregation provides failover and link aggregation capabilities. In this mode, only one IB port, that represents the two physical ports, is exposed to the application layer. For further information, please refer to the PRM. 
        * Mellanox Accelerated Switching And Packet Processing (ASAP2 ) Direct technology allows to offload OVS by handling OVS data-plain in Mellanox ConnectX-4 / ConnectX-4 Lx NIC hardware (Mellanox Embedded Switch or eSwitch) while maintaining OVS control-plain unmodified. The current actions supported by ASAP2 Direct include packet parsing and matching, forward, drop along with VLAN push/pop or VXLAN encap/decap and HW based packet/byte flow statistics.
        * Virtual Extensible LAN (VXLAN) is a network virtualization technology that improves scalability problems associated with large cloud computing deployments. It tunnels Ethernet frames within Ethernet + IP + UDP frames. Mellanox implements VXLAN encapsulation and decapsulation in the hardware.
        * [Beta] DCBX is used by DCB devices to exchange configuration information with directly connected peers. DCBX uses Link Layer Discovery Protocol (LLDP) to exchange parameters between two link peers. For further information, please refer to the PRM.
        * Enables the user to control whether or not to scatter Frame Check Sequence (FCS) or to check FCS functionality.
        * [Beta] Send Queues (SQ/ Send queue of QP) may be individually rate limited, thus, allowing granular rate control over specific SW-defined flows. A rate-limited flow is allowed to transmit a few packets before its transmission rate is evaluated, and the next packet is scheduled for transmission accordingly.
        * A new PHY test mode in which the device can generate different PRBS patterns for SerDes tuning purpose. For further information, please refer to PRM registers: PPAOS, PPTT, PPRT.
        * Added support for MCTP host management over PCI
        * Added support for OCBB/OCSD memory pointers restoration after mlxfwreset
        * Added support for MCTP media migration between SMBUS and PCI
        * Added v1, v3, v6 tags to VPD read only tag.
        * Added IPoIB checksum and LSO offload support.
        * Enables software to scatter or strip FCS in RQ.
        * Keeps track of the creation of a packet. A time-stamping service supports assertions of proof that a datum existed before a particular time.
        * Applies pause functionality to specific classes of traffic on the Ethernet link.
        * Custom port counters provide the user a clear indication about RDMA send/receive statistics and errors.
        * The Link Layer Discovery Protocol (LLDP) is a vendor-neutral Link Layer protocol in the Internet Protocol Suite used by network devices for advertising their identity, capabilities, and neighbors on a IEEE 802 LAN. The protocol is formally defined in IEEE 802.1AB.
        * ConnectX-4 adapters now support 1Gb/s and 56GbE Ethernet connectivity in addition to 10GigE, 25GigE, 40GigE, 50GigE, and 100GigE
        * Provides a clear indication of Flow Steering statistics and errors.
        * The minimal amount of packet headers inlined in the WQE's Eth Segment.
        * A flow table may include a table-miss flow entry, which renders all Match Fields wildcards. If a packet does not match a flow entry in a flow table, this is a table miss. The behavior on a table miss depends on the table configuration. A table-miss flow entry in the flow table may specify how to process unmatched packets.
        * Enables connecting multiple compute or storage hosts into a single interconnect adapter by separating the adapter PCIe interface into multiple and independent PCIe interfaces. 
        * Single Root IO Virtualization (SR-IOV) is a technology that allows a physical PCIe device to present itself multiple times through the PCIe bus.
        * Uses the HCA for offloading erasure coding calculations.
        * Enables the administrator to add a timestamp to the firmware they want to upgrade to avoid situations where one host tries to upgrade the firmware and another tries to downgrade; which may lead to two or more unnecessary server reboots. For further information, please refer to MFT User Manual.
        * The change includes the following:  
      1\. Changed port configuration which required link re-training (such as speed)  
      2\. PAOS down  
      3\. PAOS up This change, will cause the link to toggle and new configurations
      to take effect.  
      This change, will cause the link to toggle and new configurations to take
      effect
      
        * Flint utility allows performing an MD5 checksum on the non-persistent sections of the firmware image. For further information, please refer to MFT User Manual
        * Improved TX signal integrity for Electromagnetic Induction (EMI) compliance. Rev. 12
        * Large Receive Offload (LRO)
        * Large Send Offload (LSO)
        * Receive Side Scaling (RSS)
        * Global Pause
        * RoCEv1.0/RoCEv2.0
        * Flow Steering
        * Sniffer Ethernet
        * Rate Limiter (at Beta level)
        * Multi packet WQE
        *  Minimal Bandwidth Guarantee (ETS)
        *  Explicit Congestion Notification (ECN)
        * Priority Flow Control (PFC)
        *  PCIe Function Level Reset (FLR)
        * Power Management L2/L3 flow support
        * Self Loopback support
        * Transport Domain support
        * CQ2EQ remapping
        * Added support for the following commands:
        * MODIFY/QUERY_ESW_VPORT_CONTEXT
        * QUERY/MODIFY_CONG_STATUS
        * QUERY/MODIFY_CONG_PARAMS
        * QUERY_CONG_STATISTICS
        * ADD/DELETE_VXLAN_UDP_DPORT
        * VXLAN/NVGRE Stateless offload In this release, this feature is supported through Windows ONLY
        * SR-IOV EN (at Beta level)
        * CQE zipping
        * Dynamically Connected (DC) transport
        *  Wake-on-Lane/Standby
        * FlexBoot/UEFI support
        * Optic modules thermal sensing support
        * PLDM commands support
        * Improved robustness during negotiation of Clause 73 (DME)
        * Non-Volatile Configuration (NVConfig). For the complete list, lease
        * Enabled port management. Now one port can be set as Ethernet and one as InfiniBand.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.1
changelog:
  -     *Fixes in FW version 12.18.2030:**
      
        * Fixed an issue which caused bi-directional traffic 10% BW degradation in Multihost.
        * Increased the CQE zipping aggressive mode timer to 9000.
        * Moving IPoIB enhanced QP to ERR or RST state results in the corruption of the service_type and pm_state in the QPC.
        * Attaching RoCE IPv4 QPs to MCG when the vport state is set to toggle (DOWN/UP), prevents the QPs that are listed on that MCG from receiving any traffic.
        * When arming SRQ for limit event, the device might issue an event with context_index=0.
        * Occasionally, when moving UD QP from error state to RTS, the QP re-enters the error state
        * When performing Pkey check for IPoIB enhanced traffic, the Pkey membership bit is ignored.
        * Stopping the Rate Limiter while traffic is being transmitted might cause the adapter card to hang.
        * Privileged Vport egress traffic is not blocked when Vport is not active
        * PF direct pass-through is not supported in InfiniBand (since PF FLR is not supported)
        * Missing invalidation upon Set().pkey leads to bad Pkey checks.
        * Fixed an issue which caused the HCA mad response to contain the incoming packet Pkey and not the matched Pkey.
        * Modified PCIe Tx configuration.
        * Fixed an issue that prevented the software to set ECN parameters (min_rate, max_rate, rate_to_set_on_first_cnp) to values >32768.
        * Fixed an issue which caused the link speed to raise as DDR when connected with certain copper cables to devices supporting up to QDR speed.
        * Fixed an issue which prevented physical counters from reseting. Now the physical counters are reset on first driver start.
        * Fixed possible negotiation issues with 3rd parties.
        * Fixed a rare issue which caused 56GbE link to raise with errors.
        * Fixed an issue which caused scheduling_context.element_type to be taken into consideration with performing verifications, when running the modify_scheduling_context command, although the field is reserved.
        * Fixed an issue which caused the eSwitch max_average_bw ref counter to decrement in TEARDOWN_HCA/ FLR VF regardless of the max_average_bw value set, although the ref counter design was to increment on every max_average_bw != 0 (limited).
        * On rare occasions during UEFI boot cycles system got stuck while WinPE is loaded. (OS WinPE, system DL160).
        * Single FTE that catches both untagged and prio-tagged packets (by giving an FTE with match_value.vlan_tag = 0 and match_value.vid = 0) is currently not supported.
        * Flashing the firmware requires server reboot. Firmware cannot be flashed twice without server reboot after first flashing.
        * If the vport state is DOWN and a packet is sent in local loopback, the sx_sniffer tool will not function.
        * Fixed an issue causing bubbles to appear as symbol errors when link raised FDR 1x.
        * When Clause 74 Fire-Code FEC is active, and there are FC corrected errors, both the FC_correctable counter and the FC_uncoreectable counter are increment.
        * Some Port Control Register do not return to the default value after the last port owner host restarts the driver.
        * Fixed an issue which caused RX to hang when the UDP packet had a reserved UDP destination port.
        * Fixed DMAC reporting mapping per host.
        * Fixed an EEH error from PCI which caused firmware to hang.
        * Fixed the default value of the PCIe target_link_speed to Gen3 in link control2.
        * Fixed an issue which prevented LEDs from blinking when the traffic was less than 0.1% of the link speed.
        * Fixed an issue which caused the mlxconfig configuration of VF_LOG_BAR_SIZE to be ignored and to be set to 5 (32MB).
        * Fixed an issues which occasionally caused the driver to hang during unload on some VLs when configuring the SM with a VL weight 0 and running traffic on it.
        * A server getting into a Standby mode while Packet-Pacing is enabled might cause firmware to hang and driver call-trace.
        * Fixed an issue which caused unexpected QoS functionality in case of multiple sources to single destination traffic transmission.
        * Fixed an issue which occasionally caused the RX traffic to hang in DC when received a PCI error on WQE fetch.
        * Fixed OOB connection issue during Intel's ITP inject errors test.
        * Fixed an issue in IEEE Auto-Negotiation where 25G FireCode FEC and 25G Reed-Solomon FEC bits were reversed.
        * Fixed an issue which caused RX to hang when a UDP packet with destination port of RoCE v2 arrived and the data matched the DC transport service.
        * Added protection from IOPX thermal diode destabilization to prevent UEFI IPv6 PXE boot failure on ConnectX-4 Lx 25GE OCP card.
        * Fixed an issue causing single port devices to query and write Physical Port TLVs to Port 2.
        * Enabled mlxfwreset to work using the PCIe Secondary Bus Reset.
        * Fixed an issue causing link flapping as a result, incorrect link settings.
        * Fixed an issue causing wrong alignment markers to be used when running 50G with Clause91 FEC enabled.
        * Reduced the default BAR size for VF (SR-IOV) from 5 (32 MB) to 1 (2MB).
        * Added legacy interrupts support in FlexBoot.
        * Modified the TX configuration to support EMI crossing margins in 16Ghz.
        * In some cases, a Bit Error Rate is not optimal on 10G/40G links.
        * Instability of Link Training Flow occurs during 100G Auto-Negotiation.
        * Fixed a rare issue which caused the command to hang when moved the QP to RESET and back to RTS.
        * Improved RDMA READ bandwidth under packet lost scenario.
        * Added support for pnat = 1 in HCA access_reg command as required by the ibdiagnet tool.
        * Fixed the LLDP OCBB response: return value is now ascii.
        * Fixed a very rare NMI issue during PXE cycles.
        * Increased the steering hash tables static size from 128 to a maximum of 32K entries.
        * Prevented miscalculation of module temperature when using 100Gb/s cables (OPN: MFA1A00-Cxxx for 100GbE and MFA1A00-Exxx for IB EDR).
        * Fixed an issue which caused the device to hang when resetting qkey/pkey violation counter via port_info mad.
        * Changed the MTU size in OCBB report. Now MTU size does not include the packet headers.
        * Reduced one hop for Unicast RX steering, steering pipes balancing.
        * Non-volatile configuration of Port Type TLV more than 50 times might cause system hang.
        * Fixed a 25G and 50G link issue when Clause 91 RS FEC was active.
        * Added a missing invalidation of SwitchX cache upon FLR which caused the upcoming driver load to either fail or not to be able to transmit.
        * Fixed an issue which prevented Vport counters from counting local loopback packets. Packets now are filter by the self-loopback prevent
        * Reported INTx as unsupported to allow PFs Passthrough on PowerKVM.
        * SR-IOV Ethernet supports up to 18 VFs per port only.
        * Fixed and incident what allowed local (internal) loopbacked packets to be counted by the Vport counters, although Vport counters should count only traffic that crosses the Vport.
        * Fixed an issue preventing driver loading or TX traffic sending upon reboot, after ungraceful driver unload.
        * Fixed casting of BMC MAC before steering API.
        * Fixed the PCI write flow to take into consideration the PCI MTU. This fix eliminates the need for NOPs in the flow, which resulted from PPC larger PCI MTU.  
      The single queue limitation for READ is due to a hardware limitation of the
      number of READ request in a given time.
      
        * Fixed a case that caused FlexBoot to not work as expected with systems that run with "large bar" enabled (Above 4G Decoding) over Connect-IB or ConnectX-4 HCAs.
        * Fixed PLDM support for single port NICs. Currently port's relevant sensors/states are reported only for a single port.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.2
changelog:
  -     *Firmware for the following devices are updated to 12.21.1000:**
      
      825110-B21 (HPE InfiniBand EDR/Ethernet 100Gb 1-port 840QSFP28 Adapter)  
      825111-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 840QSFP28 Adapter)
      
      **New features and changes in version 12.21.1000:**
      
        * Added support for the following features: 
          * InfiniBand native (No SR-IOV) dual port device (Function per port is disabled). In this mode virtualization is not supported and ISSI = 0.
          * 10G/40G on 100GbE AOC/transceivers vs. non Mellanox devices.
        * PTP packets time stamping is enabled upon packet's arrival to the port.
        * Explicit Congestion Notification (ECN) is enabled by default for all priorities on Ethernet ports.
        * DC CNAK improves sent CNAK performance and avoids back pressure in ConnectX-4 adapter cards.
        * Receiver Signal Integrity Improvements: 
          * Raised the link only with phase greater than 15 ticks to improve signal integrity.
          * Extended measurement test between two similar RX configurations.
          * Moved the data path to use the second input buffer to improve signal integrity.
        * RDMA over Converged Ethernet (RoCE) Dual Port Mode enables the usage of a dual port Virtual HCA (vHCA) to share RDMA resources (e.g., MR, CQ, SRQ, PDs) across the two Ethernet (RoCE) NIC network ports and display the NIC as a dual port device. For this feature to function properly, the following requirements must be met: 
          * Either the LAG or the Dual Port mode is enabled by the driver.
          * Dual port device: both ports must be set as ETH.
          * In ConnectX-4/ConnectX-4 Lx adapter cards, the maximum allowed number of VFs per PF is 32.
          * Function per port is enabled.
        * QPDPM register is added to support dynamic mapping between DSCP and priority.
        * Trust level for QoS prioritization is added according to the DSCP or PCP.
        * Ingress buffer management is added for: 
          * ingress traffic mapping to a buffer according to priority.
          * buffers sizes and lossless parameters.
        * Enhanced steering rules update rate to up to 50K rules per second.
        * Enabled Windows single root input/output virtualization (SR-IOV) Enhanced eIPoIB (without Secure Connection) for Windows-over-Windows setups.
        * crdump operation takes a snapshot of the device's crspace dword-by-dword. It enables the driver to collect debug information upon firmware failure.
        * Secure Firmware Updates provides devices with the ability to verify digital signatures of new firmware binaries, in order to ensure that only officially approved versions are installed on the devices.
        * Changed the default Forward Error Connection (FEC) mode for cables with attenuation 16 and below from Reed Solomon (RS) to FC.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.2
changelog:
  -     *Fixes in version 12.21.1000:**
      
        * RDMA_CM driver was causing the Queue Pair (QP) Rate Limit to be activated unexpectedly and reduce the bandwidth significantly on this QP.
        * Low throughput when Eplicit Congestion Notification (ECN) was enabled in a many-to-one scenario.
        * A rare issue that caused the firmware to hang.
        * The maximum temperature in a setup was incorrectly reported as the current temperature regardless of the actual temperature.
        * Virtual Addressing Capability incorrect report in NC-SI (Sideband).
        * Enhanced RX sensitivity per Vcore.
        * Disabled the option to write to the protected modules to avoid receiving NACK upon module initialization.
        * Enabled cold_flicks reset when sending invalidate_all command to invalidate all the ECs.
        * SR-IOV min & max rate limiter can only support up to 64 VFs per port.
        * Explicit Congestion Notification (ECN) did not function as expected when the number of Queue Pairs (QPs) > ~500 per host.
        * When using Unreliable Datagram (UD) RDMA over Converged Ethernet (RoCE) multicast traffic over SR-IOV, packets were scattered to all the attached QPs in the e-sw (PF and its VFs) and not only on the vport that was specified in the e-se FDB.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4
changelog:
  -     *Firmware for the following devices are updated to 12.22.4030:**
      
      825110-B21 (HPE InfiniBand EDR/Ethernet 100Gb 1-port 840QSFP28 Adapter)  
      825111-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 840QSFP28 Adapter)
      
      **New features and changes in version 12.22.4030:**
      
        * **AS Notify:** AS Notify enables IBM's Power CPU architecture to boost performance by allowing the hardware to issue light weight "interrupts" to replace the traditional MSI interrupts.
        * **Dump Me Now (DMN):** Dump Me Now (DMN) generated dumps and traces from various components that are crucial for offline debugging. Once an issue is discovered, the dumps can provide useful information about the NIC's state at the time of the failure
        * Added support for DSCP mapping on QP RTS2RTS.
        * **Port Enable:** When set, the device supports emulating link down for all the associated functions using "ICMD_SET_VIRTUAL_PARAMETERS - Set Device Virtual Parameters".
        * **mlxfwreset:** Reduced and accelerated the mlxfwreset loading time of the firmware update flow.
        * **Virtual Functions (VF):** Increased the number of VFs that can work with full VMQoS (8 TC) per PFs as follow: 
          * in dual port devices to 20 VFs
          * in single port devices to 64 VFs
        * Extended the retry counter (extended_retry_count) to up to 255 instead of 7.
      
      **Firmware for the following devices are updated to 16.22.4030:**
      
      879482-B21 (HPE InfiniBand FDR/Ethernet 40/50Gb 2-port 547FLR-QSFP Adapter)  
      872726-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 841QSFP28 Adapter)
      
      **New features and changes in version 16.22.4030:**
      
        * **AS Notify:** AS Notify enables IBM's Power CPU architecture to boost performance by allowing the hardware to issue light weight "interrupts" to replace the traditional MSI interrupts.
        * **Dump Me Now (DMN):** Dump Me Now (DMN) generated dumps and traces from various components that are crucial for offline debugging. Once an issue is discovered, the dumps can provide useful information about the NIC's state at the time of the failure
        * Added support for DSCP mapping on QP RTS2RTS.
        * **Port Enable:** When set, the device supports emulating link down for all the associated functions using "ICMD_SET_VIRTUAL_PARAMETERS - Set Device Virtual Parameters".
        * **mlxfwreset:** Reduced and accelerated the mlxfwreset loading time of the firmware update flow.
        * **Virtual Functions (VF): **Increased the number of VFs that can work with full VMQoS (8 TC) per PFs as follow: 
          * in dual port devices to 20 VFs
          * in single port devices to 64 VFs
        * Extended the retry counter (extended_retry_count) to up to 255 instead of 7.
        * Added support for striding RQ in InfiniBand.
        * **QoS "Rate Limit":** Added support to limit the transmission rate of individual InfiniBand port Service Levels. This capability is configurable through a new vendor-specific MAD (QosConfigSL).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4
changelog:
  -     *Fixes in firmware version 12.22.4030 and 16.22.4030:**
      
        * In rare cases, where the width of the receiver's electrical eye is narrow, the link might raise with BER lower than 10^-12.
        * LRO timeout configuration is now taken from the TLV configuration instead of the static defined values.
        * Added a filter to ignore module temperature reads below -40C and above 125C.
        * Closed the vport as part of the fast teardown flow, to prevent Ack to be sent without been scatter to memory.
        * A rare scenario where the PERST# de-assertion arrived at a specific critical time period was handled.
        * Temperature normalization function calculation issue. Now the cable gain that is not pure integer is taken into account.
        * The parser of object 0x8 in ASN that caused different structure in response.
        * An issue that caused MSIX interrupt lost while the HCA performed an FLR was handled.
        * An issue that caused a race condition between the firmware boot process and the MSIX access from the PCIe, which resulted in lost writes into the MSIX vector was fixed.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.5
changelog:
  -     *Fixes in version** **12.24.1000 and 16.24.1000:**
      
        * mlxconfig tool reported all possible expansion ROM images, instead of presenting only the existing images.
        * Modifying VMQoS rate limiter parameters during traffic caused transmission failure.
        * Aligned the default tuning type in PHY TEST MODE to the device protocol.
        * When a device is operating in Safe Mode state, and the user issues the mlxfwreset command, the device might fail to come-up correctly after the reset.  
      Note: Do not run mlxfwreset when operating in a Safe Mode state.
      
        * Fixed an issue related to PCIe "Surprise link down" event reporting capability.
        * Fixed an issue that resulted in the link partner experiencing false active linkup when plugging in a base-T cable to a closed port.
      
      **Fixes in version** **12.24.1000:**
      
        * Fixed an issue that caused the max_qp_retry_freq_exceeded counter (including a CQE with error syndrome 0x97, and the QP moving to error state) to be activated only after exceeding the NIC Vport context max_qp_retry_limit, and not when reaching it.
      
      **Fixes in version** **16.24.1000:**
      
        * PCIe bifurcation issue.
        * Deadlock in RX related to the "send-invalidate" flow, resulted in RX getting stuck.
        * Rare errors in RX that resulted in double completion.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4-2.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager.**
        * **Customers who already installed firmware version HPG4 do not need to update to HPG4 (B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4-2.1
changelog:
  -     *Enhancements/New Features for HPG4 (B):**
      
        * Adds support for HPE ProLiant Gen10 servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4-2.1
changelog:
  -     *Problems Fixed:**
      
        * This firmware improves HDD reliability when HDDs are exposed to long periods of host inactivity that exceed 1 second. HDDs may become unresponsive when using HDD firmware prior to version HPG4.  This firmware also contains a change which prevents an incorrect reassign status of a repaired sector from being logged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG6
changelog:
  -     *Problems Fixed:**
      
        * HPG6 firmware improves drive reliability where disk drives are exposed to long periods of host inactivity which exceed 1 second.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG6-3.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager**
        * **Customers who already installed firmware version HPG6 do not need to update to HPG6(C).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG6-4.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPG6 do not need to update to HPG6(D).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.2
changelog:
  -     *Fixes in FW version 2.34.5000:**
      
        * Fixed an issue with RX size counter not being reported.
        * Fixed a rare issue with VPD init flow which caused read failures.
        * Set the maximum EQN number to 1024.
        * Fixed an issue with cable reading, which caused the link not to raise.
        * Fixed a case where on rare cases, communication to BMC was lost during driver initialization.
        * Fixed a case where the actual bandwidth did not match the user settings in VM QoS.
        * Fixed a rare case of completion Error with Bad Opcode sequence status which occurred when retransmitting read requests.
        * Fixed an issue where the port raised as SDR vs. InfiniScale IV QDR Switch.
        * Fixed a failure to update RSS QP in steering rules.
        * Fixed a case preventing broadcast traffic from arriving to their destination after detaching high priority broadcast rule on a port where NC-SI was enabled.
        * Fixed a mistakenly dropped ETH packet with ethertype 0x600 by the NIC.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.3
changelog:
  -     *Firmware for the following devices are updated to 2.35.5100:**  
        
      644161-B21  
      644160-B21  
      649282-B21  
      649281-B21  
      649283-B21  
        
      **Firmware for the following devices are updated to 2.35.5100:**  
        
      764282-B21  
      764283-B21  
      764284-B21  
        
      **Firmware for the following devices are updated to 2.35.5100:**  
        
      764285-B21  
      764286-B21


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.3
changelog:
  -     Fixes:
      
        * Fixed an issue which caused packet transmission to get stuck when the software tried to send pause frames with dmac equal to one of the device's MAC addresses.
        * Fixed an issue which caused a firmware internal error when handling QP alternative context.
        * Fixed an issue which caused an internal firmware error when APM changed the QPs port mapping.
        * Fixed an issue which caused NVRAM to get stuck when it filled non-valid information in TLV.
        * Fixed an issue which caused lack of IB traffic on SR-IOV VPI.
        * Fixed a race in handling a duplicated "read request from middle".
        * Fixed an issue which caused NVCONFIG to fail when the number of sector was set to 1 and the sector was zeroed.
        * Fixed an issue which caused TX traffic to stop when the message MTU size was larger than QP.mtu.
        * MLNX_OEM command GET_TEMP returned a wrong value in the max_temp field.
        * Fixed a default hardware configuration issue which caused RDP over IPv4 traffic to be dropped.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4-2.1
changelog:
  -     *Firmware for the following devices are updated to 2.36.5000:**  
        
      644161-B21  
      644160-B21  
      649282-B21  
      649281-B21  
      649283-B21  
        
      **Firmware for the following devices are updated to 2.36.5000:**  
        
      764282-B21  
      764283-B21  
      764284-B21  
        
      **Firmware for the following devices are updated to 2.36.5000:**  
        
      764285-B21  
      764286-B21


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4-2.1
changelog:
  -     *Fixes in 2.36.5000:**
      
        * Fixed an issue which caused packet transmission to get stuck when the software tried to send pause frames with dmac equal to one of the device's MAC addresses.
        * Fixed an issue which caused a firmware internal error when handling QP alternative context.
        * Fixed an issue which caused an internal firmware error when APM changed the QPs port mapping.
        * Fixed an issue which caused NVRAM to get stuck when it filled non-valid information in TLV.
        * Fixed an issue which caused lack of IB traffic on SR-IOV VPI.
        * Fixed a race in handling a duplicated "read request from middle".
        * Fixed an issue which caused NVCONFIG to fail when the number of sector was set to 1 and the sector was zeroed.
        * Fixed an issue which caused TX traffic to stop when the message MTU size was larger than QP.mtu.
        * MLNX_OEM command GET_TEMP returned a wrong value in the max_temp field.
        * Fixed a default hardware configuration issue which caused RDP over IPv4 traffic to be dropped.
        * Fixed performance issues causing slow performance when running in NO-DRAM-NIC mode.
        * Disabled High Rate Steering mode in the INI to enable its compatibility with NC-SI over VLAN.
        * Fixed failure instances when initiating FLR in the Physical Function.
        * Fixed a wrong returned status in cable info MAD when the cable was not connected.
        * Fixed the length calculation of UDP. The incorrect UDP length in the CNP packet caused miss-calculation of the ICRC.
        * Fixed a completion error issue when ECN was enabled. The ECN usage caused ordering errors in completion queues (CQ).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.5
changelog:
  -     *Firmware for the following devices are updated to 2.40.5030:**  
        
      644161-B21  
      644160-B21  
      649282-B21  
      649281-B21  
      649283-B21  
      764282-B21  
      764286-B21
      
      **Firmware for the following devices are updated to 2.40.5072**
      
      764283-B21  
      764284-B21  
      764285-B21
      
      **New features in firmware version 2.40.5030:**
      
        * Added temperature thresholds high/low default for MAD sensing and NCSI/IPMI OEM commands.
        * Added a new field to "set port" command which notifies the firmware what is the user_mtu size.
        * Added a protection mechanism which ensures the firmware drops packets which are received in internal QPs and disables the WQE producer fetching.
        * Added Etherent Link down counter.
        * Enables steering packets to receive queues according to Ethertype
        * Adds support for additional rate values.
        * Counters that count the number of repeated Send WQE cache lookups that resulted in a miss.
        * Flint utility allows performing an MD5 checksum on the non-persistent sections of the firmware image.
        * New performance and back-pressure counters command via PRM (For further information, please refer to the PRM)
        * Support for Multicast/Unicast sniffer rules (For further information, please refer to the PRM)
        * Support for VLAN in VLAN encapsulation (For further information, please refer to the PRM)
        * CQ creation offload by software
        * Support for rst2rts command
        * Invalidates a TLV during the firmware boot stage
        * A new counter for the diag_rprt PRM command to count packet drops due to no-receive buffer
        * Support for Ethernet TX lifetime cycle control (Head of Queue)
        * A new register (PPLR) that allows egress and external loopback control (For further information, please refer to the PRM)
        * A watchdog mechanism to track ingress traffic stalls to prevent flooding the network with Flow Control packets
        * A new LED scheme controlled by the INI which causes constant traffic LED indication even without traffic.
        * Added support for multiple RoCE modes (RoCE v1+v2) on the same port: RoCE mode is per connection now.
        * Added a new QP command "INIT2RTS_QP" to enhance QP connection readiness time.
        * Disabled FCS checks to support switches that replace FCS with Timestamp.
        * Added RX Port identification for direct rout packets.
        * Improved RDMA WRITE/SEND performance with retransmissions.
        * Enabled firmware burning/querying using the PRM ACCESS_REG command.
        * Added support for VAM.
        * Enabled bad cable EEPROM reporting to the driver.
        * Added support for Platform Level Data Model (PLDM) sideband protocol.
        * Added support for priority based A0-DMFS mode (For further information, please refer to the PRM).
        * Added support for Unicast/Multicast loopback disablement by the driver. (For further information, please refer to the PRM)
        * Removed the source IP from the hash calculation (For further information, please refer to the PRM)
        * Added support for Inline Receive mode up to 2KB.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.5
changelog:
  -     *Fixes in 2.40.5030 and 2.40.5072:**
      
        * Fixed a race between the firmware and the hardware during driver start which blocked outbound completions.
        * Fixed an issue which caused the firmware not to send link_down event to the driver when running the close_port command.
        * Fixed an issue where in rare cases the Auto Sense failed to detect the right protocol.
        * Fixed signal integrity issue when connecting a WCS ConnectX4 mezz card to Pikes peak FPGA.
        * Added the option to transmit corrupted DME pages for a very short period of time at the beginning of the Auto-Negotiation flow.
        * Fixed an incorrect report of the PortRcvDataVLExtended/ PortXmitDataVLExtended counters by the firmware.
        * Fixed a rare issue which caused firmware's packet injector to cut off packets when the TX was congested.
        * Fixed an issue that caused the response to TX requests to take up to 10 miliseconds in IEEE clause 72 Link Training.
        * Fixed a race between 2 iriscs which caused a QP to get stuck in burst control limit state.
        * When a QP was in error state, the firmware generated too many err CQEs at once, thus causing the cmdif responsiveness to be too slow. To prevent the above, the number of err CQEs was limited to 16 at a time.
        * Fixed an issue that caused the MAC address that was set from the OS using ifconfig to be not reflected in the OCBB buffer.
        * Fixed an issue where the ibdump got broken when running with loopback traffic.
        * Fixed an issue where the firmware took QP to firmware ownership and then released it to the hardware ownership without checking if another firmware flow owns the same QP.
        * Fixed an issue which occurred after disconnecting cable which showed the link type as IB even if the link type of the port is ETH.
        * Fixed an issue related to the HCA PoerXmitWait counter on port 2 (connected to port 2 on Switch-IB) where it started counting and reached 0xFF's regardless of connection to switch.
        * Fixed a completion error issue when ECN was enabled. The ECN usage caused ordering errors in completion queues (CQ).
        * Fixed the length calculation of UDP. The incorrect UDP length in the CNP packet caused miss-calculation of the ICRC.
        * Fixed a wrong returned status in cable info MAD when the cable was not connected.
        * Fixed failure instances when initiating FLR inthe Physical Function.
        * Disabled High Rate Steering mode in the INI to enable its compatibility with NC-SI over VLAN.
        * Fixed performance issues causing slow performance when running in NO-DRAM-NIC mode.
        * Fixed a default hardware configuration issue which caused RDP over IPv4 traffic to be dropped.
        * Prevented a Virtual Function from injecting pause frames into the network.
        * MLNX_OEM command GET_TEMP returned a wrong value in the max_temp field.
        * Fixed an issue which caused TX traffic to stop when the message MTU size was larger than QP.mtu.
        * Fixed an issue which caused NVCONFIG to fail when the number of sector was set to 1 and the sector was zeroed.
        * Fixed a race in handling a duplicated "read request from middle".
        * Fixed an issue which caused lack of IB traffic on SR-IOV VPI.
        * Fixed an issue which caused NVRAM to get stuck when it filled non-valid information in TLV.
        * Fixed an issue which caused an internal firmware error when APM changed the QPs port mapping.
        * Fixed an issue which caused a firmware internal error when handling QP alternative context.
        * Fixed an issue which caused packet transmission to get stuck when the software tried to send pause frames with dmac equal to one of the device's MAC addresses.
        * Fixed a mistakenly dropped ETH packet with ethertype 0x600 by the NIC.
        * Fixed a case preventing broadcast traffic from arriving to their destination after detaching high priority broadcast rule on a port where NC-SI was enabled.
        * Fixed a failure to update RSS QP in steering rules.
        * Fixed an issue where the port raised as SDR vs. InfiniScale IV QDR Switch.
        * Fixed a rare case of completion Error with Bad Opcode sequence status which occurred when retransmitting read requests.
        * Fixed a case where the actual bandwidth did not match the user settings in VM QoS.
        * Fixed a case where on rare cases, communication to BMC was lost during driver initialization.
        * Fixed an issue with cable reading, which caused the link not to raise.
        * Set the maximum EQN number to 1024.
        * Fixed a rare issue with VPD init flow which caused read failures.
        * Fixed an issue with RX size counter not being reported.
        * The first Read response was not treated as implicit ACK.
        * Reduced a long 40GbE link up time with Cisco Nexus3064 and Arista-7050S.
        * Fixed promiscuous mode compatibility with A0-DMFS steering.
        * Fixed promiscuous mode compatibility when NC-SI is enabled and configured.
        * Fixed sending/receiving OEM temp commands (set/get) with channel ID 0x1f failure.
        * Fixed an issue which caused packets to drop on a port when changing the interface state of the other port.
        * Fixed long management communication loss and SOL hang during reboot cycles.
        * Fixed wrong processing of inbound traffic towards BMC which caused communication loss.
        * Fixed management link loss upon closing port interface through the driver.
        * Fixed a false indication in firmware of an expander presence causing delay in EEPROM reading.
        * Fixed an issue which caused a link down on a port when the cable was removed from the other port.
        * Fixed a rare case where packet with length zero got stuck in hardware queues.
        * Fixed an issue which caused InfiniBand congestion control packet (CNP) to hang in hardware.
        * Fixed an issue which caused AEN to be sent after channel reset.
        * Fixed an issue which prevented the restoring of QoS setting to its default consequently causing bandwidth degradation.
        * Fixed an occasional long link up time with 10GbE based devices.
        * Fixed an issue preventing cable readings from i2c slave address 0x51.
        * Fixed a possible deadlock in PM turnoff request transmission and ack acceptance flow.
        * Fixed a rare case with alignments state machines which caused occasional width degradation.
        * Fixed an issue where the transmit queues hanged while congestion control was enabled and operational (EQC/QCN).
        * Fixed an unexpected work completion syndrome with vendor syndrome 0x77 received when running RDMA SEN/WRITE traffic with retransmissions.
        * Fixed an issue which caused SetPortInfo to return a good status when receiving invalid LinkSpeedEnabled value.
        * Fixed an issue which caused dual port SFPP module cards to be automatically mapped with expander. Fixed an issue where firmware overrides the steering mode that was chosen by the driver.
        * Fixed invalid return sensing results occurred when the link was up.
        * Fixed an issue causing the sensing result to be delayed when cable was unplugged.
        * Fixed an issue causing the link type to be displayed as ETH when set to AUTO.
        * Fixed 2us glitch in Wake Up signal.
        * Fixed performance degradation when running IBDump.
        * Occasionaly, a link training timeout occurred in EQ phase0 during disable/enable test.
        * Improved strict bandwidth mode functionality.
        * Fixed an issue with the PortRcvPkts counter always displaying zero value.
        * Fixed an issue with processing GMP MADs with SET method in SecureHost mode.
        * Fixed an issue causing a wrong usage of MCG size when configuring Global Multicast filter.
        * Disabling the first port occasionally causes second port TX failure.
        * Fixed a mismach in links status reported. The adapter reports links as down while the switch perceives them as up.
        * Fixed an occasional 40GbE link failure with SCM5 Switch blade.
        * Fixed a wrong FDR10 speed reporting in MAD.
        * Fixed an issue preventing theports to to rise up when set to FDR10 vs QDR.
        * Fixed an occasional link failure vs Arista switch.
        * Retransmission started from the first PSN of message instead of the last acknowledged PSN.
        * Firmware hangs when receiving GeneralInfoMad during inline firmware burning.
        * L1 flow adjustments and threshold tuning.
        * Fixed a rare hanging issue during PERST_ assertion.
        * Wrong coefficients were reported during phase3.
        * Fixed an issue causing wrong behavior due to reset timing.
        * Fixed lack of steering options.
        * Fixed long timeout issues.
        * Fixed NVRAM write issues in driver-less mode.
        * Fixed 40GbE link support in aux mode.
        * Dropped commands with non-existing channel ID.
        * Fixed issues in extended speed reporting.
        * Fixed bad QP reporting in trap 257/8.
        * Fixed an issue causing false bad q_key error messages.
        * Fixed Pause Frame opcode mismatch.
        * Fixed communication loss upon PCIe error detection.
        * Fixed wrong channel value in the SELECT/ DESELECT PACKAGE commands.
        * Fixed an issue caused response packet to include 4 extra bytes.
        * Fixed wrong reason code value returned when using Set Link command with unsupported speed.
        * Added protection from bad MAC address given by BMC. Removed false TX pulse after PERST_ deassertion.
        * Fixed FLR capability bit inconsistency when SR-IOV is enabled.
        * Fixed an issue with the device not reporting PCIe related errors.
        * When a link is configured to DDR in a setup of ConnectX-3 to SX6036, SDR link is established instead.
        * VXLAN used the wrong default UDP port. the UDP port number was changed to 4789.
        * Fixed wrong setting of the UDP destination port for VXLAN.
        * Fixed an internal error caused when moving to the DMS mode with IPMI/NC-SI enabled.
        * In a back-to-back setup of FDR cards connected with a 0.5m FDR cable, a link may be established as FDR10 instead of FDR.
        * Fixed issues related to working with PCI legacy interrupts.
        * Wrong checksum calculation for short packets which are padded by the software.
        * Reading PCIe configuration space after using the MFT flint tool caused the device to crash.
        * Fixed occasional packet loss over IPMI.
        * Fixed wrong values reported in the Eye opening MAD.
        * Fixed occasional link width degrades during link negotiation and link transitions from L1 state.
        * Fixed adjust signal detect thresholds.
        * PortExtendedSpeedsCounters MAD counters were mistakenly increased while LLR was active.
        * Lane reversal was not considered when configured TX parameters.
        * Fixed ROL factory MAC usage when a Flex- Boot address was given.
        * Fixed Pause frames factory MAC usage when FlexBoot address was given.
        * The device did not different between WOL/ROL packets.
        * Fixed a set of extended fields in PortInfo MAD which did not function.
        * Adjusted LLR cell size according to the MLPN negotiation of ib_128b_llr.
        * The max speed restriction was active in full power mode instead of standby mode only.
        * The InfiniBand Path migration did not work with GRH. http://webdev01:8080/commit/ConnectX.git/a9c37ee4c31038f2c1179d4d9e79c9337e0ab5c7 
        * Reading MGM after writing it returned wrong members count.
        * Fixed corruption of the RSS hash key given by the driver.
        * Fixed QoS rate limit BW offset.
        * Fixed FDR10 speed_en reporting.
        * Fixed long management link com loss.
        * The command results reported both link types active at the same time. Fixed collision between forcing phy type and port sensing. Fixed a wrong core clock freq reporting in QUERY_HCA command.
        * Fixeds occasional link failure when 56GbE is enabled.
        * Fixed max eye margins to be per protocol.
        * perfquery reported wrong error symbol on ConnectX(C)-3 VPI mode: IB, ETH.
        * On ConnectX-3Pro dual-port QDR and FDR/FDR10 switch setups, symbol errors may occur with MC2207312-030 AOCs.
        * Symbol errors occur on ConnectX-3Pro dualport QDR connected to FDR switches with MC2207126-004 copper cables.
        * Driver restart required when switching from InfiniBand FDR link with LLR enabled to InfiniBand link w/o LLR (for example: between SwitchX and GD4036).
        * On rare occasions, the adapter card may fail to link up when performing parallel detect to 40GbE.
        * Automatic Path Migration (APM) did not update the new MGIDs from the Alternate Path.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.6
changelog:
  -     *Firmware for the following devices are updated to 2.40.5030:**  
      764286-B21  
      778509-B21
      
      **Firmware for the following devices are updated to 2.40.5072:**  
      764285-B21
      
      **Firmware for the following devices are updated to 2.42.5004:**  
      764283-B21  
      764284-B21
      
      **Firmware for the following devices are updated to 2.42.5000:**  
      764282-B21
      
      **New features in firmware version 2.40.5030:**
      
        * Added support for the following features. 
          * Temperature thresholds high/low default for MAD sensing and NCSI/IPMI OEM commands.
          * A new field is added to "set port" command which notifies the firmware what is the user_mtu size.
          * A protection mechanism which ensures the firmware drops packets which are received in internal Queue Pairs (QPs) and disables the WQE producer fetching.
      
      **New features in firmware version 2.40.5072:**
      
        * Platform Level Data Model (PLDM) support.
      
      **New features in firmware version 2.42.5000:**
      
        * Added support for the following features. 
          * new TLV: CX3_GLOBAL_CONF to enable/disable timestamp on incoming packets through mlxconfig configuration.
          * User MAC configuration.
          * Automatically collecting mstdump before driver reset.
          * A mechanism to detect DEAD_IRISC (plastic) from TPT (iron) and raise an assert.
          * A new field is added to "set port" command which notifies the firmware what is the user_mtu size.
        * Improved the debug ability for command timeout cases


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.6
changelog:
  -     *Fixes in version 2.40.5030 and 2.40.5072:**
      
        * Race between the firmware and the hardware during driver start which blocked outbound completions.
        * The firmware did not send link_down event to the driver when running the close_port command.
      
      **Fixes in version 2.42.5000:**
      
        * PortRcvPkts counter was prevented from being cleared after resetting it.
        * The system Timed Out on the configuration cycle of the Virtual Functions (VFs) when more than 10 Virtual Functions performed FLR and the completion Time Out value was configured to a range of less than 16 msec.
        * The server hangs and results in NMI when running "mlxfwtop -d mt4103_pci_cr0" while restarting the driver in parallel (from a different thread). In this case, the downstream bridge over the device reported completion timeout error.
        * In flow_steering, BMC could not receive a ping over IPV6 after running bmc_reboot.
        * While closing the HCA, the RX packet caused bad access to resources that did not exist, and consequently caused the QPCGW or the irisc to get stuck.
        * The master SMLID and the LID was either 0 or 0xFFFF when the port was neither active nor armed.
        * ibdump could not capture all MADs packets.
        * link did not go up after reboot.
        * Fixed a rare issue that cause the PCIe configuration cycle that arrived during the time of sw_reset to generate 2 completions.
        * Network Controller Sideband Interface (NC-SI) did not work when adding the disable_static_steering_ini field in the ini file, due to memory allocation issue for this field in the scratchpad.
      
      **Fixes in version 2.42.5004:**
      
        * In UEFI (Unified Extensible Firmware Interface) HII (Human Interface Infrastructure) menu, when using HPE Gen10 devices, both ports appear as port 1.
        * In UEFI (Unified Extensible Firmware Interface) boot menu, when using HPE Gen10 devices,  the device name appears with an unneeded port number.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.7
changelog:
  -     *Fixes in version 2.42.5000:**
      
        * PortRcvPkts counter was prevented from being cleared after resetting it.
        * The system Timed Out on the configuration cycle of the Virtual Functions (VFs) when more than 10 Virtual Functions performed FLR and the completion Time Out value was configured to a range of less than 16 msec.
        * The server hangs and results in NMI when running "mlxfwtop -d mt4103_pci_cr0" while restarting the driver in parallel (from a different thread). In this case, the downstream bridge over the device reported completion timeout error.
        * In flow_steering, BMC could not receive a ping over IPV6 after running bmc_reboot.
        * While closing the HCA, the RX packet caused bad access to resources that did not exist, and consequently caused the QPCGW or the irisc to get stuck.
        * The master SMLID and the LID was either 0 or 0xFFFF when the port was neither active nor armed.
        * ibdump could not capture all MADs packets.
        * link did not go up after reboot.
        * Fixed a rare issue that cause the PCIe configuration cycle that arrived during the time of sw_reset to generate 2 completions.
        * Network Controller Sideband Interface (NC-SI) did not work when adding the disable_static_steering_ini field in the ini file, due to memory allocation issue for this field in the scratchpad.
      
      **Fixes in version 2.42.5044:**
      
        * Fixed an issue that  prevented the firmware from detecting a link_down event thus preventing the IB bond interface from going to a failover mode


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD1
changelog:
  -      **Online firmware flashing of drives attached to an HP Smart Array controller running in Zero Memory (ZM) mode or an HP ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD1
changelog:
  -     *Problem Fixed:**
      
        * Incorrect data reads might occur when accessing unaligned 4k reads and the data read has zero content preceding customer data.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD1-2.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPD1 do not need to update to HPD1 (B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD1-2.1
changelog:
  -     *Problem Fixed:**
      
        * Incorrect data reads might occur when accessing unaligned 4k reads and the data read has zero content preceding customer data.
      
      **Problems Fixed for HPD1 (B):**
      
        * Component would fail to install drive firmware for drives present in a system configured with two or more external drive enclosures attached to an HP Host Bus Adapter H22x. The following message would be reported in the component log file - "Device appears more than once in tree". The drive firmware installation failure was not observed in configurations having only one external drive enclosure attached to an HP Host Bus Adapter H22x.
        * Component fails to update the firmware for drives connected behind an HP Smart Array P431 controller. Component reports the firmware update was successful. However, after a power cycle, the firmware version remains unchanged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3-2.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPD3 do not need to update to HPD3(B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2
changelog:
  -     *Problems Fixed:**
      
        * This firmware contains a change to prevent occasional command completion times in the 4-5 second window when command is received just as the drive is transitioning from active to Idle A.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2-2.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPD2 do not need to update to HPD2(B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2-3.1
changelog:
  -      This firmware contains a change to prevent occasional command completion times in the 4-5 second window when command is received just as the drive is transitioning from active to Idle A.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG2
changelog:
  -      Corrects a potential data integrity issue during unaligned write commands, found in supplier ongoing lab testing.Includes additional fixes to improve error handling and reliability.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG2-2.1
changelog:
  -      Corrects a potential data integrity issue during unaligned write commands, only found in supplier ongoing lab testing.Includes additional fixes to improve error handling and reliability.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2
changelog:
  -     *Problems Fixed:**
      
        * This firmware improves HDD reliability when HDDs are exposed to long periods of host inactivity that exceed 1 second. HDDs may become unresponsive when using HDD firmware prior to version HPD2.  This firmware also contains a change which prevents an incorrect reassign status of a repaired sector from being logged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3
changelog:
  -     *Problems Fixed:**
      
        * Under rarely occurring conditions where a host error occurred during a write with 4K unaligned sectors, the write operation might result in stale data. Firmware HPD3 prevents the possibility of stale data occurring under these conditions.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5-2.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager**
        * **Customers who already installed firmware version HPD5 do not need to update to HPD5(B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5-3.1
changelog:
  -      This firmware includes a fix for slow performance during sequential write workloads with small queue depth.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4
changelog:
  -     *Enhancements/New Features:**
      
        * Firmware version HPG4 is designed to prevent any previous firmware revisions from being loaded onto the drive, after the drive is upgraded to HPG4 firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4
changelog:
  -     *Problems Fixed:**
      
        * This firmware corrects a potential issue where the data in the reserved tracks is not properly updated, eliminating the risk of a drive not finishing the boot process on power up.
        * Other maintenance fixes and updates are also included with the new firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4-2.1
changelog:
  -     *Enhancements/New Features:**
      
        * Firmware version HPG4 is designed to prevent any previous firmware revisions from being loaded onto the drive, after the drive is upgraded to HPG4 firmware. 
      
      ******Enhancements/New Features for HPG4 (B):**
      
        * Adds support for HPE ProLiant Gen10 servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4-3.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPG4 do not need to update to HPG4(c).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4-4.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPG4 do not need to update to HPG4(D).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4
changelog:
  -     *Problems Fixed:**
      
        * Firmware version HPG4 prevents the occurrence of a rare issue which could lead to slow drive performance. This issue has the potential to impact all drives in configurations where the drives might be allowed to be idle for greater than 1 second.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4-5.1
changelog:
  -      Firmware version HPG4 prevents the occurrence of a rare issue which could lead to slow drive performance. This issue has the potential to impact all drives in configurations where the drives might be allowed to be idle for greater than 1 second.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2
changelog:
  -     *Problems Fixed:**
      
        * This firmware update eliminates a data integrity risk when an unaligned WRITE and VERIFY command is sent to a bad sector. During these conditions there is a potential for data intended to be written to disk to fail to be written.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3-2.1
changelog:
  -      Improves JetStress READ Latency performance.
        * Fixes the cause of internal reboots detected in the MSA system.
        * Removes a vendor unique sense code that the controller does not handle properly.
        * Includes changes to eliminate the cause of a potential hang condition.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4
changelog:
  -     *Problems Fixed:**
      
        * Under rarely occurring conditions where a host error occurred during a write with 4K unaligned sectors, the write operation might result in stale data. Firmware HPx4 prevents the possibility of stale data occurring under these conditions.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG5-2.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager**
        * **Customers who already installed firmware version HPG5 do not need to update to HPG5(B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3
changelog:
  -      This firmware has a change that allows the drive to meet the requirements for Azure Stack certification.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3-2.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPG3 do not need to update to HPG3(B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3-2.1
changelog:
  -      This firmware has a change that allows the drive to meet the requirements for Azure Stack certification.
        * Fixed the issue of Online firmware update fails when drives are connected behind AHCI controller.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1
changelog:
  -      Adds support for the HPE Security Log Page BBh, and improves drive reliability and responsiveness by including the latest firmware maintenance updates.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD8
changelog:
  -     *Enhancements/New Features:**
      
        * Improves Sequential Write and Random Write Performance under certain workloads.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD8
changelog:
  -     *Problems Fixed:**
      
        * Fixes a data integrity risk which could occur during 4k or greater unaligned writes while the device incurs a smart trip event. During these conditions there is a potential for data intended to be written directly to disk to fail to be written.
        * Eliminates a data integrity risk when an unaligned Write and Verify command is sent to a bad sector. During these conditions there is a potential for data intended to be written to disk to fail to be written.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD8-2.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPD8 do not need to update to HPD8(B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD9
changelog:
  -     This firmware:  
      Fixes the cause of internal reboots detected in the MSA system.  
      Removes a vendor unique sense code that the controller does not handle
      properly.  
      Includes changes to eliminate the cause of a potential hang condition.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4
changelog:
  -      Firmware corrects potential data integrity issues caused by incomplete cache table updates during unaligned writes, an incorrect write retry start location calculation, and improper media read ranges overlapped with cached writes.  These issues were only found during supplier ongoing reliability testing.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5
changelog:
  -      This code corrects a potential data integrity issue related to unaligned write commands.This issue was only found in supplier ongoing lab testing.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK1
changelog:
  -      This firmware corrects the potential for a drive to become disabled and nonfunctional during certain conditions or workloads.After the drive is upgraded to firmware version HPK1, it cannot be downgraded to firmware version HPK0.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG6
changelog:
  -      Corrects a potential data integrity issue caused by an in process write retry incorrectly starting at the wrong location.  This issue was found during supplier ongoing reliability testing.
        * The firmware also corrects settings preservation after a code download, and includes emergency power off improvements.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG6-3.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPG6 do not need to update to HPG6(C).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG6-3.1
changelog:
  -      Corrects a potential data integrity issue caused by an in process write retry incorrectly starting at the wrong location.  This issue was found during supplier ongoing reliability testing.
        * The firmware also corrects settings preservation after a code download, and includes emergency power off improvements.
      
        * Fixed the issue of Online firmware update fails when drives are connected behind AHCI controller.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1
changelog:
  -     *Enhancements/New Features :**
      
        * HPG1 is a maintenance firmware release with minor performance enhancements for 2.5" SSD 6Gb SATA drive models VK0240GEPQN, VK0480GEPQP, and VK0960GEPQQ .
        * Adds support for HPE ProLiant Gen10 servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1-2.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPG1 do not need to update to HPG1(B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1-3.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPG1 do not need to update to HPG1(C).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD1-2.1
changelog:
  -     *Problem Fixed:**
      
        * Incorrect data reads might occur when accessing unaligned 4k reads and the data read has zero content preceding customer data. For additional information please refer to the customer advisory #[c04650586](http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c04650586)
      
      **Problems Fixed for HPD1 (B):**
      
        * Component would fail to install drive firmware for drives present in a system configured with two or more external drive enclosures attached to an HP Host Bus Adapter H22x. The following message would be reported in the component log file - "Device appears more than once in tree". The drive firmware installation failure was not observed in configurations having only one external drive enclosure attached to an HP Host Bus Adapter H22x.
        * Component fails to update the firmware for drives connected behind an HP Smart Array P431 controller. Component reports the firmware update was successful. However, after a power cycle, the firmware version remains unchanged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD1-3.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager.**
        * **Customers who already installed firmware version HPD1 do not need to update to HPD1 (C).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD1-3.1
changelog:
  -     *Enhancements/New Features for HPD1 (C):**
      
        * Adds support for HPE ProLiant Gen10 servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5-2.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPD5 do not need to update to HPD5(B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD6-2.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPD6 do not need to update to HPD6(B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD7
changelog:
  -      This firmware fixes an infrequent drive internal reset issue.  When managing a Task Set Full condition in its firmware the drive may do an internal reset. The drive may not be accessible during the reset recovery process.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG7-3.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPG7 do not need to update to HPG7 (C).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG7-3.1
changelog:
  -     *Problems Fixed:**
      
        * This firmware corrects possible unrecovered errors caused by the track refresh algorithm not working properly.
      
      **Problems Fixed for HPG7 (C):**
      
        * Component would fail to install drive firmware for drives present in a system configured with two or more external drive enclosures attached to an HP Host Bus Adapter H22x. The following message would be reported in the component log file - "Device appears more than once in tree". The drive firmware installation failure was not observed in configurations having only one external drive enclosure attached to an HP Host Bus Adapter H22x.
        * Component fails to update the firmware for drives connected behind an HP Smart Array P431 controller. Component reports the firmware update was successful. However, after a power cycle, the firmware version remains unchanged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPGA
changelog:
  -     *Enhancements/New Features:**
      
        * Provides support for Microsoft Azure Stack requirements.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPGB-2.1
changelog:
  -      Corrects a potential data integrity issue caused by an in process write retry incorrectly starting at the wrong location.  This issue was only found during supplier ongoing reliability testing.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPGB-3.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPGB do not need to update to HPGB(C).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPGB-3.1
changelog:
  -      Corrects a potential data integrity issue caused by an in process write retry incorrectly starting at the wrong location.  This issue was only found during supplier ongoing reliability testing.
        * Fixed the issue of Online firmware update fails when drives are connected behind AHCI controller.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4
changelog:
  -     *Problems Fixed:**
      
        * Under rarely occurring conditions where a host error occurred during a write with 4K unaligned sectors, the write operation might result in stale data. Firmware HPD4 prevents the possibility of stale data occurring under these conditions.
        * After greater than 2 seconds of idle time following a forced power transition or no activity, random seeks might not occur as required. Firmware HPD4 initiates random seeks following  the device being placed into a forced power condition. Random seeks are necessary to maintain the reliability and life of the device.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4-2.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager.**
        * **Customers who already installed firmware version HPD4 do not need to update to HPD4 (B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4
changelog:
  -     *Problems Fixed:**
      
        * Improves the drive idle time behavior by reducing long periods of track dwell time, which if not implemented, could increase media lube depletion and reduce drive reliability.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4-2.1
changelog:
  -     *Enhancements/New Featuresfor HPG4 (B):**
      
        * Adds support for HPE ProLiant Gen10 servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4-3.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager**
        * **Customers who already installed firmware version HPG4 do not need to update to HPG4(C).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2
changelog:
  -     *Problems Fixed:**
      
        * Reliability enhancement for applications that write data to a narrow range of tracks.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4
changelog:
  -      **Online firmware flashing of drives attached to an HP Smart Array controller running in Zero Memory (ZM) mode or an HP ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux and Microsoft Windows environments. All other OSes would require an offline update using the SPP and HP SUM.**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4
changelog:
  -     *Problems Fixed:**
      
        * Reliability enhancement for applications that write data to a narrow range of tracks.
      
      **Known Issues:**
      
        * Firmware cannot be downgraded to HPG3 after updating to HPG4.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4-2.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager.**
        * ****Customers who already installed firmware version HPG4 do not need to update to HPG4 (B).****


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5
changelog:
  -     *Enhancements/New Features:**
      
        * Changes Light Emitting Diode (LED) behavior to match Hewlett Packard Enterprise specification.
        * Strengthens link acquisition algorithm.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5
changelog:
  -     *Problems Fixed:**
      
        * Fixes a data integrity risk which could occur during 4k or greater unaligned writes while the device incurs a smart trip or smart warning event. During these conditions there is a potential for data intended to be written directly to disk to fail to be written.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5-2.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager.**
        * **Customers who already installed firmware version HPD5 do not need to update to HPD5 (B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5-2.1
changelog:
  -     *Enhancements/New Features:**
      
        * Changes Light Emitting Diode (LED) behavior to match Hewlett Packard Enterprise specification.
        * Strengthens link acquisition algorithm.
        * Adds support for HPE ProLiant Gen10 servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD6
changelog:
  -     *Problems Fixed:**
      
        * This firmware eliminates a data integrity risk when an unaligned Write and Verify command is sent to a bad sector. During these conditions there is a potential for data intended to be written to disk to fail to be written.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD7
changelog:
  -      Added FW binary unencrypted.
        * This firmware:  
      1) Improves JetStress READ Latency performance  
      2) Fixes the cause of internal reboots detected in the MSA system  
      3) Removes a vendor unique sense code that the controller does not handle
      properly  
      4) Includes changes to eliminate the cause of a potential hang condition


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD7-2.1
changelog:
  -      This firmware:  
      1) Improves JetStress READ Latency performance  
      2) Fixes the cause of internal reboots detected in the MSA system  
      3) Removes a vendor unique sense code that the controller does not handle
      properly  
      4) Includes changes to eliminate the cause of a potential hang condition


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3
changelog:
  -     *Problems Fixed:**
      
        * This firmware implements the Firmware Security Log Page.
      
        * This firmware contains a change to prevent occasional command completion times in the 4-5 second window when command is received just as the drive is transitioning from active to Idle A.


author: Prashant Sreedharan <prashant@broadcom.com> - 1.0.14
changelog:
  - CQ73669: No support for 5717C0 devid (Severity: Minor)
  - CQ73746: tg3sd fails to run on RH7.0 (Severity: Minor)
  - hp-tg3sd-x.x.x.rpm fails to install on SLES11sp3 (Severity: Minor)


author: Siva Reddy Kallam <siva.kallam@broadcom.com> - 1.0.19
changelog:
  - CTRL-20577: tg3sd does not run under RHEL 7.2 (Severity: Minor)
  - CTRL-20998: 330i Network information missing in AHS (Severity: Minor)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK1
changelog:
  -      Firmware corrects an issue where the drive will be in a failed state after an unexpected power loss. When this occurs the drive will not recover after subsequent power cycles and will not be accessible by the system configuration and Host applications.
        * Refer Customer Bulletin for workarounds <https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00042733en_us>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK1-2.1
changelog:
  -      Firmware corrects an issue where the drive will be in a failed state after an unexpected power loss. When this occurs the drive will not recover after subsequent power cycles and will not be accessible by the system configuration and Host applications.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4
changelog:
  -     *Problems Fixed:**
      
        * This firmware contains several low level maintenance fixes including debug data retrieval through read buffer.  The fixes addressed events observed in a specialized lab testing environment, and are not expected to be experienced in customer use case scenarios.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD6
changelog:
  -     *Problems Fixed:**
      
        * During a hot removal/hot plug event, the drive failed discovery operation. To address this problem, the drive firmware handling of the Start/Stop Unit command has been improved.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD6-2.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager.**
        * **Customers who already installed firmware version HPD6 do not need to update to HPD6(B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD6-3.1
changelog:
  -      During a hot removal/hot plug event, the drive failed discovery operation. To address this problem, the drive firmware handling of the Start/Stop Unit command has been improved.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG6-2.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPG6 do not need to update to HPG6(B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK4
changelog:
  -      Fixed timing issue to pass VMWare VSAN certification. Downgrading to any previous version of firmware is not allowed.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1
changelog:
  -     *Problems Fixed:**
      
        * This firmware improves HDD reliability when HDDs are exposed to long periods of host inactivity that exceed 1 second. HDDs may become unresponsive when using HDD firmware prior to version HPG1. 
        * This firmware also contains a change which prevents an incorrect reassign status of a repaired sector from being logged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1-2.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager.**
        * **Customers who already installed firmware version HPG1 do not need to update to HPG1 (B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1-2.1
changelog:
  -     *Enhancements/New Features for HPG1 (B):**
      
        * Adds support for HPE ProLiant Gen10 servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1-3.1
changelog:
  -      Added support for SmartRAID 3154-8e RAID controller.
        * Added support for HPE Smart Array P824i-p MR Gen10 controller.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4-2.1
changelog:
  -      This firmware updates the drive to indicate NDU compliance.
        * Online firmware update fails when drives are connected behind AHCI controller.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG5
changelog:
  -      This firmware includes a fix for an issue where the LED would continue blinking after a Sanitize operation completed.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK4
changelog:
  -      Fixes a potential latency issue caused by an incorrect pre-fetch algorithm. 
        * Resolves an issue with a possible bus hang during a system reboot.
        * Once HPK4 is downloaded, the drive firmware cannot be changed back to an earlier firmware version (eg, HPK3 or HPK2) due to security changes


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1
changelog:
  -     *Problems Fixed:**
      
        * Firmware corrects an issue where drives were not found during Power-On Self-Test device discovery.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1-4.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPG1 do not need to update to HPG1(D).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1-5.1
changelog:
  -      Firmware corrects an issue where drives were not found during Power-On Self-Test device discovery.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG2-2.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager.**
        * **Customers who already installed firmware version HPG2 do not need to update to HPG2 (B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG2-2.1
changelog:
  -     *Enhancements/New Features for HPG2 (B):**
      
        * Adds support for HPE ProLiant Gen10 servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG2-3.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager**
        * **Customers who already installed firmware version HPG2 do not need to update to HPG2(C).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG2-4.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPG2 do not need to update to HPG2(D).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4
changelog:
  -      This firmware adds a feature that will periodically assess the health of the writer element of the head by verifying the data after a write operation to ensure more robust data integrity.
        * When performing format on drives with marginal servo flaws, it takes too long to format or format fails with 03/31 reported across the interface on subsequent commands. This firmware includes a change that moves the servo flaw characterization retries earlier in the sequence of format.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4-2.1
changelog:
  -     *Problems Fixed:**
      
        * The expected time to completion of Sanitize, Format and DST operations was incorrectly reported in the Vital Products Data page D0h. If time to completion is used by an application to determine when to terminate an operation, the operation might be terminated before the operation completed. Firmware version HPD4 now correctly reports the expected time to completion for these operations.
      
      **Problems Fixed for HPD4 (B):**
      
        * Component would fail to install drive firmware for drives present in a system configured with two or more external drive enclosures attached to an HP Host Bus Adapter H22x. The following message would be reported in the component log file - "Device appears more than once in tree". The drive firmware installation failure was not observed in configurations having only one external drive enclosure attached to an HP Host Bus Adapter H22x.
        * Component fails to update the firmware for drives connected behind an HP Smart Array P431 controller. Component reports the firmware update was successful. However, after a power cycle, the firmware version remains unchanged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD6
changelog:
  -     *Problems Fixed:**
      
        * This firmware contains a change to prevent an incorrect sense code from being posted when a Stop command is received during power-on sequence.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD6-2.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * ****Customers who already installed firmware version HPD6 do not need to update to HPD6 (B).****


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD6-2.1
changelog:
  -     *Problems Fixed:**
      
        * This firmware improves HDD reliability when HDDs are exposed to long periods of host inactivity that exceed 1 second. HDDs may become unresponsive when using HDD firmware prior to version HPD6. 
      
        * This firmware also contains a change which prevents an incorrect reassign status of a repaired sector from being logged.
      
        * This firmware contains a change to prevent an incorrect sense code from being posted when a Stop command is received during power-on sequence.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG2
changelog:
  -      Fixes an issue where the drive may become unresponsive and stop functioning under certain initial usage conditions (eg, idle, low workloads, or continuous system reboot).
        * For more information, refer to HPE Customer Advisory at the following URL: <https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00041830en_us>.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3-2.1
changelog:
  -     Firmware version HPG3 addresses the following issues:
      
        * Corrects the potential for drives to become unresponsive. For details about this issue, refer to HPE Customer Bulletin: HPE Solid State Drives (SSD) - SSD FIRMWARE UPGRADE REQUIRED to Prevent a Higher Than Expected Failure Rate Noted on Certain Model SSD Drives: <https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00048133en_us>.   
        * Improves drive reliability by including the latest firmware maintenance updates.  
        
      After HPG3 firmware is downloaded to the drive, the new HPG3 firmware will be
      active on the drive. The new drive bootloader code will be activated after the
      next drive power cycle.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3-3.1
changelog:
  -     Firmware version HPG3(C) addresses the following issue :
      
        * Added a fix for changing the order of write buffer modes in the flash engine.
      
      Firmware version HPG3 addresses the following issues:
      
        * Corrects the potential for drives to become unresponsive. For details about this issue, refer to HPE Customer Bulletin: HPE Solid State Drives (SSD) - SSD FIRMWARE UPGRADE REQUIRED to Prevent a Higher Than Expected Failure Rate Noted on Certain Model SSD Drives: <https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00048133en_us>.   
        * Improves drive reliability by including the latest firmware maintenance updates.  
        
      After HPG3 firmware is downloaded to the drive, the new HPG3 firmware will be
      active on the drive. The new drive bootloader code will be activated after the
      next drive power cycle.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5
changelog:
  -     *Problems Fixed:**
      
        * This firmware improves HDD reliability when HDDs are exposed to long periods of host inactivity that exceed 1 second. HDDs may become unresponsive when using HDD firmware prior to version HPD5.  This firmware also contains a change which prevents an incorrect reassign status of a repaired sector from being logged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5-2.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager.**
        * ****Customers who already installed firmware version HPD5 do not need to update to HPD5 (B).****


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5-2.1
changelog:
  -     *Enhancements/New Features for HPD5 (B):**
      
        * Adds support for HPE ProLiant Gen10 servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD9
changelog:
  -     *Problems Fixed:**
      
        * This firmware contains a change to prevent a drive reset issue, which may affect performance.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD9-2.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager**
        * **Customers who already installed firmware version HPD9 do not need to update to HPD9(B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4
changelog:
  -     *Problems Fixed:**
      
        * Version HPD4 prevents the potential for incorrect data to be written to the drive under extremely rare circumstances when the drive experiences a hard reset. This issue has only been observed in a rigorous test environment and has NOT been reported in a customer production environment.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4-2.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPD4 do not need to update to HPD4 (B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4-2.1
changelog:
  -     *Problems Fixed:**
      
        * Version HPD4 prevents the potential for incorrect data to be written to the drive under extremely rare circumstances when the drive experiences a hard reset. This issue has only been observed in a rigorous test environment and has NOT been reported in a customer production environment.
      
      **Problems Fixed for HPD4 (B):**
      
        * Component would fail to install drive firmware for drives present in a system configured with two or more external drive enclosures attached to an HP Host Bus Adapter H22x. The following message would be reported in the component log file - "Device appears more than once in tree". The drive firmware installation failure was not observed in configurations having only one external drive enclosure attached to an HP Host Bus Adapter H22x.
        * Component fails to update the firmware for drives connected behind an HP Smart Array P431 controller. Component reports the firmware update was successful. However, after a power cycle, the firmware version remains unchanged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD7
changelog:
  -     *Problems Fixed:**
      
        * This firmware improves HDD reliability when HDDs are exposed to long periods of host inactivity that exceed 1 second. HDDs may become unresponsive when using HDD firmware prior to version HPD7. 
      
        * This firmware also contains a change which prevents an incorrect reassign status of a repaired sector from being logged.
      
        * This firmware prevents asserts on a sequential write which can result in devices being lost from the configuration. It also preserves persistent reservation through downloads which prevents loss of performance.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD8
changelog:
  -      This firmware allows the drive to meet the requirements for Azure Stack certification. 
        * This firmware contains a change to the reported drive serial number in VPD page 80. It will now report the same as is displayed on the drive label.  Any removed characters are replaced with blank place holders so the log format will not be changed.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD1
changelog:
  -      This firmware includes a fix for an issue that could cause timeout errors during certain sequential write corner cases. There is also a fix for slow response time during random write workloads.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2
changelog:
  -      This firmware includes a fix for an issue where a drive could become format corrupt after a power cycle if write commands were being executed before the power loss.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK2
changelog:
  -      Additional improvements in MCTP functionality.
        * Drive fails to train in BL460 after Windows warm reset or iLO reset.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK4
changelog:
  -      Fixed timing issue to pass VMWare VSAN certification.  Downgrading to any previous version of firmware is not allowed.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1
changelog:
  -      Fixes an issue which caused the drive to become non-functional.  
       Fixes VPD Log D0h reported drive Sanitize times.  
       Adds support for Security Log Page BBh


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1-2.1
changelog:
  -      Fixes an issue which caused the drive to become non-functional.  
       Fixes VPD Log D0h reported drive Sanitize times.  
       Adds support for Security Log Page BBh.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4-2.1
changelog:
  -     *Problems Fixed:**
      
        * Self-initiated reset during ATI (Adjacent Track Interference) mitigation issue, where the drive reported a 06/29/04 (Self-Initiated Reset) to the controller.  Then the controller would re-establish link with the drive and resend the command.
        * Servo miscalculations that resulted in degraded drive performance.
      
      **Problems Fixed for HPD4 (B):**
      
        * Component would fail to install drive firmware for drives present in a system configured with two or more external drive enclosures attached to an HP Host Bus Adapter H22x. The following message would be reported in the component log file - "Device appears more than once in tree". The drive firmware installation failure was not observed in configurations having only one external drive enclosure attached to an HP Host Bus Adapter H22x.
        * Component fails to update the firmware for drives connected behind an HP Smart Array P431 controller. Component reports the firmware update was successful. However, after a power cycle, the firmware version remains unchanged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4-3.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager.**
        * ****Customers who already installed firmware version HPD4 do not need to update to HPD4 (C).****


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4-3.1
changelog:
  -     *Enhancements/New Features for HPD4 (C):**
      
        * Adds support for HPE ProLiant Gen10 servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD6-3.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager**
        * **Customers who already installed firmware version HPD6 do not need to update to HPD6(C).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG2
changelog:
  -     *Problems Fixed:**
      
        * Firmware version HPG2 prevents the occurrence of a rare issue which could lead to slow drive performance. This issue has the potential to impact all drives in configurations where the drives might be allowed to be idle for greater than 1 second.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG2-2.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPG2 do not need to update to HPG2(B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG2-3.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPG2 do not need to update to HPG2(C).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG2-4.1
changelog:
  -      Firmware version HPG2 prevents the occurrence of a rare issue which could lead to slow drive performance. This issue has the potential to impact all drives in configurations where the drives might be allowed to be idle for greater than 1 second.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4-5.1
changelog:
  -      This firmware corrects a potential issue where the data in the reserved tracks is not properly updated, eliminating the risk of a drive not finishing the boot process on power up.  This firmware is also designed to prevent any previous firmware revisions to be loaded onto the drive, once the HPG4 firmware is downloaded.  Other maintenance fixes and updates are also included with the new firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG7-3.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager.**
        * ****Customers who already installed firmware version HPG7 do not need to update to HPG7 (C).****


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG7-3.1
changelog:
  -     *Enhancements/New Features for HPG7 (C):**
      
        * Adds support for HPE ProLiant Gen10 servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG7-3.1
changelog:
  -     *Problems Fixed:**
      
        * This firmware corrects possible unrecovered errors caused by the track refresh algorithm not working properly.
      
      **Problems Fixed for HPG7 (B):**
      
        * Component would fail to install drive firmware for drives present in a system configured with two or more external drive enclosures attached to an HP Host Bus Adapter H22x. The following message would be reported in the component log file - "Device appears more than once in tree". The drive firmware installation failure was not observed in configurations having only one external drive enclosure attached to an HP Host Bus Adapter H22x.
        * Component fails to update the firmware for drives connected behind an HP Smart Array P431 controller. Component reports the firmware update was successful. However, after a power cycle, the firmware version remains unchanged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPGB-2.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager**
        * **Customers who already installed firmware version HPGB do not need to update to HPGB(B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPGB-3.1
changelog:
  -      Fixed the issue of Online firmware update fails when drives are connected behind AHCI controller.
        * Corrects a potential data integrity issue caused by an in process write retry incorrectly starting at the wrong location. This issue was found during supplier ongoing reliability testing.
      
        * The firmware also corrects settings preservation after a code download, and includes emergency power off improvements.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPGB-4.1
changelog:
  -      Corrects a potential data integrity issue caused by an in process write retry incorrectly starting at the wrong location. This issue was found during supplier ongoing reliability testing.
        * The firmware also corrects settings preservation after a code download, and includes emergency power off improvements.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK2
changelog:
  -      After a warm reboot, the drive would fail to be recognized.
        * Addressed a potential for data integrity issues during unaligned data transfers.
        * A drive would become non-functional due to a disabled logic state that resulted from a vSAN PCIe Advance Error Reporting issue where device registers were accessed before they became ready.  
      
       For details about this issue, refer to HPE Customer Bulletin:
      <https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00052541en_us>  
      
       **Important:** After the drive is upgraded to firmware version HPK2, it cannot be downgraded firmware version HPK0.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK2-2.1
changelog:
  -      Resolves an issue where the drive may fail to be recognized after a warm reboot.
        * Corrects a potential data integrity issue during unaligned data transfers.
        * Fixes an issue where the drive may become disabled during improper access of error registers.
        * Once HPK2 is downloaded, the drive cannot be changed back to HPK0 firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2
changelog:
  -      This firmware changes some settings to comply with Microsoft Storage Spaces Certification requirements.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPS4
changelog:
  -     *Problems Fixed:**
      
        * HPS4 firmware release resolved a firmware timing issue which occurred during drive long self-test and resulted in a timeout condition that caused the drive to become unrecognized by the system.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPS4-3.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPS4 do not need to update to HPS4(c).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPS4-4.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPS4 do not need to update to HPS4(D).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPS4-5.1
changelog:
  -      HPS4 firmware release resolved a firmware timing issue which occurred during drive long self-test and resulted in a timeout condition that caused the drive to become unrecognized by the system.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2
changelog:
  -      Removes a vendor unique sense code that the controller does not handle properly.
        * Includes changes to eliminate the cause of a potential hang condition.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD9
changelog:
  -     *Problems Fixed:**
      
        * When configured in an HPE D6000 Disk Enclosure, a drive might fail disk discovery operation. This firmware corrects the drive's loss of signal detection, which is the root of the reported problem.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPDB
changelog:
  -     *Problems Fixed:**
      
        * This firmware improves potential timeouts that could occur during the write error recovery process (causing the drive to internally reset), and corrects possible data mismanagement issues.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPDB-2.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPDB do not need to update to HPDB(B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPDB-3.1
changelog:
  -      This firmware improves potential timeouts that could occur during the write error recovery process (causing the drive to internally reset), and corrects possible data mismanagement issues.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3
changelog:
  -      This firmware has a change that allows the drive to meet the requirements for Microsoft Azure Stack certification.  It also includes a fix for an issue that could cause timeout errors during certain sequential write corner cases.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3-2.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPG3 do not need to update to HPG3 (B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3-2.1
changelog:
  -     *Problems Fixed:**
      
        * After HDD power cycle, the Background Media Scan (BGMS) pointer would invoke a second BGMS routine starting at LBA 0, which could affect  performance until the second BGMS has completed.
        * When writing to the HDD after it entered or returned from a standby state, the potential existed for a Non Volatile Cache issue to occur..
      
      **Problems Fixed for HPG3 (B):**
      
        * Component would fail to install drive firmware for drives present in a system configured with two or more external drive enclosures attached to an HP Host Bus Adapter H22x. The following message would be reported in the component log file - "Device appears more than once in tree". The drive firmware installation failure was not observed in configurations having only one external drive enclosure attached to an HP Host Bus Adapter H22x.
        * Component fails to update the firmware for drives connected behind an HP Smart Array P431 controller. Component reports the firmware update was successful. However, after a power cycle, the firmware version remains unchanged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG5
changelog:
  -     *Problems Fixed:**
      
        * This firmware improves HDD reliability when HDDs are exposed to long periods of host inactivity that exceed 1 second. HDDs may become unresponsive when using HDD firmware prior to version HPG5.  This firmware also contains a change which prevents an incorrect reassign status of a repaired sector from being logged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG5-2.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager.**
        * **Customers who already installed firmware version HPG5 do not need to update to HPG5 (B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG8-2.1
changelog:
  -      This firmware updates the drive to indicate NDU compliance.
        * Fixed the issue of Online firmware update fails when drives are connected behind AHCI controller.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD6-2.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager**
        * **Customers who already installed firmware version HPD6 do not need to update to HPD6(B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD6-3.1
changelog:
  -      This firmware provides a drive command update that allows the drive to become fully ready before returning good status during the power up sequence.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPS6-3.1
changelog:
  -     *Firmware Dependency:**
      
        * Drive models XP0032GEFEN, XP0032GDZME, XP0064GDZMF, and XP0064GEFEP must have firmware version HPS5 installed prior to updating to firmware version HPS6.
      
      **Enhancements/New Features:**
      
        * Improves firmware upgrade process by using a single firmware file instead of multiple files for upgrading all capacities of drives in this drive family.
      
        * Improves TRIM command handling.
      
      **Enhancements/New Features for HPS6 (B):**
      
        * Adds support for HPE ProLiant Gen10 servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPS8
changelog:
  -     *Firmware Dependency:**
      
        * ****Drive models XP0032GEFEN, XP0032GDZME, XP0064GDZMF, and XP0064GEFEP must have firmware version HPS6 installed prior to updating to firmware version HPS8.
      
      **Problems Fixed:**
      
        * HPS8 firmware release resolved a firmware timing issue which occurred during drive long self-test and resulted in a timeout condition that caused the drive to become unrecognized by the system.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPS8-2.1
changelog:
  -     *Firmware Dependency:**
      
        * Drive models XP0032GEFEN, XP0032GDZME, XP0064GDZMF, and XP0064GEFEP must have firmware version HPS6 installed prior to updating to firmware version HPS8.
      
      **Problems Fixed:**
      
        * HPS8 firmware release resolved a firmware timing issue which occurred during drive long self-test and resulted in a timeout condition that caused the drive to become unrecognized by the system.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPS8-3.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager**
        * **Customers who already installed firmware version HPS8 do not need to update to HPS8(C).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPS8-4.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPS8 do not need to update to HPS8(D).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPS8-5.1
changelog:
  -      HPS8 firmware release resolved a firmware timing issue which occurred during drive long self-test and resulted in a timeout condition that caused the drive to become unrecognized by the system.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5-2.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPD5 do not need to update to HPD5 (B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5-2.1
changelog:
  -     *Problems Fixed:**
      
        * Self-initiated reset during ATI (Adjacent Track Interference) mitigation issue, where the drive reported a 06/29/04 (Self-Initiated Reset) to the controller.  Then the controller would re-establish link with the drive and resend the command.
        * Servo miscalculations that resulted in degraded drive performance.
      
      **Problems Fixed for HPD5 (B):**
      
        * Component would fail to install drive firmware for drives present in a system configured with two or more external drive enclosures attached to an HP Host Bus Adapter H22x. The following message would be reported in the component log file - "Device appears more than once in tree". The drive firmware installation failure was not observed in configurations having only one external drive enclosure attached to an HP Host Bus Adapter H22x.
        * Component fails to update the firmware for drives connected behind an HP Smart Array P431 controller. Component reports the firmware update was successful. However, after a power cycle, the firmware version remains unchanged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2
changelog:
  -      Fixes the cause of internal reboots detected in the MSA system.
        * Removes a vendor unique sense code that the controller does not handle properly.
        * Includes changes to eliminate the cause of a potential hang condition.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD1
changelog:
  -     *Problems Fixed:**
      
        * This firmware improves HDD reliability when HDDs are exposed to long periods of host inactivity that exceed 1 second. HDDs may become unresponsive when using HDD firmware prior to version HPD1.  This firmware also contains a change which prevents an incorrect reassign status of a repaired sector from being logged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2
changelog:
  -     *Problems Fixed:**
      
        * This firmware prevents asserts on a sequential write which can result in devices being lost from the configuration. It also preserves persistent reservation through downloads which prevents loss of performance.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3-2.1
changelog:
  -      This firmware allows the drive to meet the requirements for Azure Stack certification. 
        * This firmware contains a change to the reported drive serial number in VPD page 80. It will now report the same as is displayed on the drive label.  Any removed characters are replaced with blank place holders so the log format will not be changed


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.1.0.28
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      This is the initial version of the firmware.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.1.2.6
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where HPE Jitter support may not respond to configuration
      changes from the Integrated Lights-Out webpage.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.1.4.4
changelog:
  -     *Important Notes:**
      
      This is a new release of HPE Gen10 Innovation Engine (IE) Firmware revision
      0.1.4.4. System ROM V1.26 must be installed prior to updating to IE FW
      0.1.4.4. This revision of the IE FW is required for updating the Intel
      Platform Service (SPS) Firmware revision 04.00.04.288 and later. It should be
      installed prior to updating to SPS FW 04.00.04.288 or later. SPS FW
      04.00.04.288 mitigates security vulnerability CVE-2017-5706
      (http://www.cve.mitre.org/cgi-bin/cvename.cgi?name=2017-5706) and
      CVE-2017-5709 (http://www.cve.mitre.org/cgi-bin/cvename.cgi?name=2017-5709).
      It is anticipated that details regarding these security vulnerabilities will
      be published to these links on November 20,2017. These security
      vulnerabilities are not unique to HPE servers.  
      
      **Firmware Dependencies:**
      
      System ROM V1.26  
      
      **Problems Fixed:**
      
      This is a new release of HPE Gen10 Innovation Engine (IE) Firmware revision
      0.1.4.4. System ROM V1.26 must be installed prior to updating to IE FW
      0.1.4.4. This revision of the IE FW is required for updating the Intel
      Platform Service (SPS) Firmware revision 04.00.04.288 and later. It should be
      installed prior to updating to SPS FW 04.00.04.288 or later. SPS FW
      04.00.04.288 mitigates security vulnerability CVE-2017-5706
      (http://www.cve.mitre.org/cgi-bin/cvename.cgi?name=2017-5706) and
      CVE-2017-5709 (http://www.cve.mitre.org/cgi-bin/cvename.cgi?name=2017-5709).
      It is anticipated that details regarding these security vulnerabilities will
      be published to these links on November 20,2017. These security
      vulnerabilities are not unique to HPE servers.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.1.5.2
changelog:
  -     *Important Notes:**
      
       HPE Innovation Engine (IE) Firmware 0.1.4.4 has been removed from the web for
      the following reasons:
      
      1\. Systems could experience a rare issue where processor and memory
      temperatures stop reporting, resulting in increased system fan speeds. This
      issue is seen during a system reboot and is only recovered by another system
      reset. This issue did not exist with previous versions of the Innovation
      Engine Firmware.
      
      2\. Systems configured with Jitter Smoothing support could experience a rare
      issue where on a given boot the functionality does not function. Resetting the
      system typically corrects the issue. This issue did not exist with previous
      versions of the Innovation Engine Firmware.
      
      3\. Systems configured with the Intel Xeon Scalable 6143 Gold and 8165
      Platinum processors with HPE's Core Boosting support enabled could experience
      a rare issue where on a given boot the functionality does not function.
      Resetting the system typically corrects the issue. This issue did not exist
      with previous versions of the Innovation Engine Firmware.
      
      This is a new release of HPE Gen10 Innovation Engine (IE) Firmware revision
      0.1.5.2 to replace IE version 0.1.4.4. If updating from IE version 0.1.4.4,
      follow the installation notes. If updating from an IE version prior to 0.1.4.4
      please read the following note.
      
      System ROM V1.26 must be installed prior to updating to IE FW 0.1.5.2. This
      revision of the IE FW is required for updating the Intel Platform Service
      (SPS) Firmware revision 04.00.04.288 and later. It should be installed prior
      to updating to SPS FW 04.00.04.288 or later. SPS FW 04.00.04.288 mitigates
      security vulnerability CVE-2017-5706 (http://www.cve.mitre.org/cgi-
      bin/cvename.cgi?name=2017-5706) and CVE-2017-5709 (http://www.cve.mitre.org
      /cgi-bin/cvename.cgi?name=2017-5709). The details regarding these security
      vulnerabilities were published to these links on November 20,2017. These
      security vulnerabilities are not unique to HPE servers.
      
      **Firmware Dependencies:**
      
      System ROM V1.26 or later  
      
      **Problems Fixed:**
      
      Addressed an issue where systems configured with Innovation Engine Firmware
      0.1.4.4 could experience a rare issue where processor and memory temperatures
      stop reporting, resulting in increased system fan speeds. This issue is seen
      during a system reboot and is only recovered by another system reset. This
      issue did not exist with previous versions of the Innovation Engine Firmware.
      
      Addressed an issue where systems configured with Innovation Engine Firmware
      0.1.4.4 and Jitter Smoothing support could experience a rare issue where on a
      given boot the functionality does not function. Resetting the system typically
      corrects the issue. This issue did not exist with previous versions of the
      Innovation Engine Firmware.
      
      Addressed an issue where systems configured with Innovation Engine Firmware
      0.1.4.4 and the Intel Xeon Scalable 6143 Gold and 8165 Platinum processors
      with HPE's Core Boosting support enabled could experience a rare issue where
      on a given boot the functionality does not function. Resetting the system
      typically corrects the issue. This issue did not exist with previous versions
      of the Innovation Engine Firmware.
      
      **Known Issues:**
      
      This flash component will report the Current Revision of the Innovation Engine
      FW as "n/a" when updating the Innovation Engine FW. This does not affect the
      flash update or impact how the Innovation Engine FW operates.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.1.6.1
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      System ROM V1.26 or later
      
      **Problems Fixed:**
      
      Addressed an issue where the Integrated Lights-Out (iLO) web interface may
      incorrectly report the Innovation Engine is running in a degraded state.
      
      Addressed an issue where memory telemetry data may not be reported properly in
      the Integrated Lights-Out (iLO) web interface or through the HPE RESTful API.
      
      Addressed an issue where the Innovation Engine Firmware flash would fail if a
      previous flash attempt was interrupted and not completed successfully.
      
      **Known Issues:**
      
      This flash component will report the Current Revision of the Innovation Engine
      FW as "n/a" when updating the Innovation Engine FW. This does not affect the
      flash update or impact how the Innovation Engine FW operates.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.1.6.1-3.1
changelog:
  -     *Important Notes:**
      
      Ver. 0.1.6.1(C) contains updates to the component packaging and is
      functionally equivalent to ver. 0.1.6.1.  It is not necessary to upgrade with
      Revision C if a previous component Revision was used to upgrade the firmware
      to version 0.1.6.1.
      
      **Firmware Dependencies:**
      
      System ROM V1.26 or later  
      
      **Problems Fixed:**
      
      Addressed an issue where the Integrated Lights-Out (iLO) web interface may
      incorrectly report the Innovation Engine is running in a degraded state.
      
      Addressed an issue where memory telemetry data may not be reported properly in
      the Integrated Lights-Out (iLO) web interface or through the HPE RESTful API.
      
      Addressed an issue where the Innovation Engine Firmware flash would fail if a
      previous flash attempt was interrupted and not completed successfully.
      
      **Known Issues:**
      
      This flash component will report the Current Revision of the Innovation Engine
      FW as "n/a" when updating the Innovation Engine FW. This does not affect the
      flash update or impact how the Innovation Engine FW operates.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.2.0.11
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an extremely rare issue where updates to the Intel Server Platform
      Services (SPS) firmware may fail.
      
      **Known Issues:**
      
      This flash component will report the Current Revision of the Innovation Engine
      FW as "n/a" when updating the Innovation Engine FW. This does not affect the
      flash update or impact how the Innovation Engine FW operates.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.1.7
changelog:
  -     This product now supports Red Hat Enterprise Linux 7 Update 4.  
      This product now supports SUSE Linux Enterprise Server 12 SP3.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.1.7
changelog:
  -     This product corrects an issue where a prompt to save configuration changes is
      displayed when no changes have been made from the adapter's configuration
      menu.  
      This product addresses an issue where an adapter fails to boot to PXE with
      VLAN ID enabled.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.2.16
changelog:
  -      This product corrects an issue where a user sees a 'Submit Fail for Form:' error message when attempting to load the default (F7) adapter settings.
        * This product corrects an issue where the user is prompted to save changes when no adapter configuration settings have been modified.
        * This product corrects an issue where an adapter's branding information is lost when a non-English language is selected for the 'System Utilities' (F9) menu.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.5.11
changelog:
  -     This product corrects an issue where adapters incorrectly send a NULL padded
      System Description LLDP (Link Layer Discovery Protocol) TLV.
      
      This product corrects an issue where an incorrect device (Network Controller)
      name is displayed in the RBSU.
      
      This product corrects an issue where adapters become Firmware corruption
      during rebooting.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.17.6
changelog:
  -     This product addresses an issue where the server makes high speed fan noise
      after the PXE firmware on the adapter is updated to version 17.0.2.
      
      This product addresses an issue where an incorrect firmware version is
      reported when updating firmware on the HP Ethernet 1Gb 2-port 332i Adapter.
      
      This product addresses an issue where older smart components report an
      incorrect Bootcode version after the firmware on the adapter was originally
      updated using the component version 2.16.4 or later.
      
      This product addresses an issue where an error code 7 is reported when
      updating firmware on the HP Ethernet 1Gb 4-port 331i-SPI Adapter.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.18.15
changelog:
  -     This product addresses an issue where an adapter disappears when the system
      configuration settings are restored to defaults.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.19.6
changelog:
  -     This product addresses an issue where negative temperatures on the adapter are
      incorrectly displayed in Integrated Lights Out (iLO).  
      This product addresses an issue where an incorrect firmware image is landed on
      an adapter.  
      This product addresses an issue where an adapter's configuration menu doesn't
      correctly prompt for reboot after changes are made that require a reboot.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.20.7
changelog:
  -      This product corrects an issue where an adapter's configuration menu doesn't prompt for reboot after changes are made that require a reboot.
        * This firmware now correctly displays a progress bar information when updating the firmware via the 'Firmware Update' feature (under 'System Utilities->Embedded Applications').


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.21.3
changelog:
  -     This product addresses an issue where the NIC Serial Number for the HPE
      Ethernet 1Gb 4-port 331FLR Adapter is not displayed in AHS.
      
      The firmware in this product  addresses an issue where the "Reboot Required"
      icon is not highlighted after a NIC firmware update (via System
      Utilities->Embedded Application->Firmware Update) completes.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.11.14
changelog:
  -     This firmware corrects an issue where the following network adapters may not
      appear in the system's boot order:
      
        * HPE Ethernet 10Gb 2-port 562FLR-SFP+ Adapter
        * HPE Ethernet 10Gb 2-port 562SFP+ Adapter
        * HPE Ethernet 10Gb 2-port 563i Adapter


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.13.12
changelog:
  -     This product now supports Red Hat Enterprise Linux 7 Update 4.  
      This product now supports SUSE Linux Enterprise Server 12 SP3.
      
      This product now supports the following network adapters:
      
        * HPE Ethernet 1Gb 2-port 368i Adapter
        * HPE Ethernet 1Gb 2-port 368FLR-MMT Adapter
        * HPE Ethernet 1Gb 4-port 369i Adapter
        * HPE Ethernet 10Gb 2-port 562FLR-T Adapter
        * HPE Ethernet 10Gb 2-port 562T Adapter
        * HPE Ethernet 10Gb 2-port 568FLR-MMSFP+ Adapter
        * HPE Ethernet 10Gb 2-port 568FLR-MMT Adapter


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.14.13
changelog:
  -      This product corrects a Wake-on-LAN (WoL) issue seen with the HP Ethernet 1Gb 2-port 361T Adapter.
        * This product corrects an issue where there is no VLAN function under Legacy mode on the HP Ethernet 1Gb 2-port 361T Adapter.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.14.14
changelog:
  -     This product addresses an issue where link flapping is seen when the 'HP
      Ethernet 10Gb 2-port 560FLB Adapter' is connected to 1Gb interfaces and
      operated at 1Gb speeds.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.15.9
changelog:
  -     This product addresses a NIC VLAN ID issue seen in the NIC Human Interface
      Infrastructure (HII) menu when operating in UEFI mode.  
      This product addresses a teaming issue where the HPE Ethernet 10Gb 2-port 561T
      Adapter still shows connected on the switch after the NIC has been disabled.  
      This product addresses a link issue and a PXE issue seen with the HPE Ethernet
      10Gb 2-port 560FLB Adapter.  
      This product addresses a WOL issue seen with the HPE Ethernet 1Gb 4-port 366T
      Adapter.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.17.17-2.1
changelog:
  -     This product addresses a failure to update adapter firmware on a system
      running SUSE Linux Enterprise Server 15.  
      This product corrects an issue where the name for the HP Ethernet 1Gb 4-port
      366FLR Adapter is displayed incorrectly in the network boot options.  
      This product corrects an issue where the HPE Ethernet 10Gb 2-port 562FLR-T
      Adapter can be awakened when the NIC WOL setting is disabled.  
      This product corrects an issue where system hangs when booting from the PXE
      boot menu.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4-3.1
changelog:
  -     *Fixes in 2.36.5000:**
      
        * Fixed an issue which caused packet transmission to get stuck when the software tried to send pause frames with dmac equal to one of the device's MAC addresses.
        * Fixed an issue which caused a firmware internal error when handling QP alternative context.
        * Fixed an issue which caused an internal firmware error when APM changed the QPs port mapping.
        * Fixed an issue which caused NVRAM to get stuck when it filled non-valid information in TLV.
        * Fixed an issue which caused lack of IB traffic on SR-IOV VPI.
        * Fixed a race in handling a duplicated "read request from middle".
        * Fixed an issue which caused NVCONFIG to fail when the number of sector was set to 1 and the sector was zeroed.
        * Fixed an issue which caused TX traffic to stop when the message MTU size was larger than QP.mtu.
        * MLNX_OEM command GET_TEMP returned a wrong value in the max_temp field.
        * Fixed a default hardware configuration issue which caused RDP over IPv4 traffic to be dropped.
        * Disabled High Rate Steering mode in the INI to enable its compatibility with NC-SI over VLAN.
        * Fixed failure instances when initiating FLR in the Physical Function.
        * Fixed a wrong returned status in cable info MAD when the cable was not connected.
        * Fixed the length calculation of UDP. The incorrect UDP length in the CNP packet caused miss-calculation of the ICRC.
        * Fixed a completion error issue when ECN was enabled. The ECN usage caused ordering errors in completion queues (CQ).
      
      **Fixes in 14.14.2204:**
      
        * Fixed an issue which prevented MAC address changes by to driver to be reflected in the OBCC and NC-SI interfaces.
        * Added protection from IOPX thermal diode destabilization to prevent UEFI IPv6 PXE boot failure on ConnectX-4 Lx 25GE cards.
        * Fixed an issue which caused a link down in Port 2 when unplugging the cable from Port 1.
        * In some cases, a Bit Error Rate is not optimal on 10G/40G links.
        * Instability of Link Training Flow occurs during 100G Auto-Negotiation.
        * Fixed a rare issue which caused the command to hang when moved the QP to RESET and back to RTS.
        * Improved RDMA READ bandwidth under packet lost scenario.
        * Added support for pnat = 1 in HCA access_reg command as required by the ibdiagnet tool.
        * Fixed the LLDP OCBB response: return value is now ascii.
        * Fixed a very rare NMI issue during PXE cycles.
        * Increased the steering hash tables static size from 128 to a maximum of 32K entries.
        * Prevented miscalculation of module temperature when using 100Gb/s cables (OPN: MFA1A00-Cxxx for 100GbE).
        * Reduced one hop for Unicast RX steering, steering pipes balancing.
        * Non-volatile configuration of Port Type TLV more than 50 times might cause system hang.
        * Enabled RoCE IPv4 Multicast. This prevents MCG command from failing when an IPv4 is mapped to an IPv6 address.
        * If the PF driver or the tool (e.g. ethtool) use PAOS DOWN command (e.g. by ifconfig down or ip link set down), loopback traffic is blocked for all functions on this port (PF<->VFs / VF<->VF) In Multihost loopback, the traffic will be blocked once the firmware receives the PAOS down command from all PFs. However, the loopback traffic will not be blocked when the port is down  due to the physical link (for example: cable plugged out, switch port down).
        * Fixed a 25G and 50G link issue when Clause 91 RS FEC was active.
        * Added a missing invalidation of eSwitch cache upon FLR which caused the upcoming driver load to either fail or not to be able to transmit.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.5-2.1
changelog:
  -     *Firmware for the following devices are updated to 2.40.5030:**  
        
      779799-B21 (HP Ethernet 10G 2-port 546FLR-SFP+ Adapter)  
      779793-B21 (HP Ethernet 10G 2-port 546SFP+ Adapter)
      
      **New features and changes in version 2.40.5030:**
      
        * Added Etherent Link down counter.
        * Enables steering packets to receive queues according to Ethertype matching 
        * Adds support for additional rate values. 
        * Counters that count the number of repeated Send WQE cache lookups that resulted in a miss.
        * Flint utility allows performing an MD5 checksum on the non-persistent sections of the firmware image.
        * New performance and back-pressure counters command via PRM (For further information, please refer to the PRM)
        * Support for Multicast/Unicast sniffer rules (For further information, please refer to the PRM)
        * Support for VLAN in VLAN encapsulation (For further information, please refer to the PRM)
        * CQ creation offload by software
        * Support for rst2rts command
        * Invalidates a TLV during the firmware boot stage
        * A new counter for the diag_rprt PRM command to count packet drops due to noreceive buffer
        * Support for Ethernet TX lifetime cycle control (Head of Queue)
        * A new register (PPLR) that allows egress and external loopback control (For further information, please refer to the PRM)
        * A watchdog mechanism to track ingress traffic stalls to prevent flooding the network with Flow Control packets
        * Inspur LED scheme: A new LED scheme controlled by the INI which causes constant traffic LED indication even without traffic.
        * Added support for multiple RoCE modes (RoCE v1+v2) on the same port: RoCE mode is per connection now.
        * Added a new QP command "INIT2RTS_QP" to enhance QP connection readiness time.
        * Disabled FCS checks to support switches that replace FCS with Timestamp.
        * Added RX Port identification for direct rout packets.
        * Improved RDMA WRITE/SEND performance with retransmissions.
        * Enabled firmware burning/querying using the PRM ACCESS_REG command.
        * Added support for VAM.  Enabled bad cable EEPROM reporting to the driver.
        * Added support for Platform Level Data Model (PLDM) sideband protocol.
        * Added support for priority based A0-DMFS mode (For further information, please refer to the PRM).
        * Added support for Unicast/Multicast loopback disablement by the driver. (For further information, please refer to the PRM)
        * Removed the source IP from the hash calculation (For further information, please refer to the PRM)
        * Added support for Inline Receive mode up to 2KB.
        * Added support for multiple RoCE modes (RoCE v1+v2) on the same port: RoCE mode is per connection now.
        * Added a new QP command "INIT2RTS_QP" to enhance QP connection readiness time.
        * Disabled FCS checks to support switches that replace FCS with Timestamp.
        * Added RX Port identification for direct rout packets.
        * Improved RDMA WRITE/SEND performance with retransmissions.
        * Enabled firmware burning/querying using the PRM ACCESS_REG command.
        * Added support for VAM.  Enabled bad cable EEPROM reporting to the driver.
        * Added support for Platform Level Data Model (PLDM) sideband protocol.
        * Added support for priority based A0-DMFS mode (For further information, please refer to the PRM).
        * Added support for Unicast/Multicast loopback disablement by the driver. (For further information, please refer to the PRM)
        * Removed the source IP from the hash calculation (For further information, please refer to the PRM)
        * Added support for Inline Receive mode up to 2KB.
        * Sideband moved to port 0
        * Added MCTP command support
        * Changed the HP LED scheme for the 779799-B21 adapter.
      
      **Firmware for the following devices are updated to 14.18.2030****:**
      
      817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)  
      817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
        * Added logical link indication in SFP to BaseT modules and disabled logical link when peer port is down.
        * Added support for 10GbE in 25GbE SFP optical modules.
        * Enables mlxlink tool to collect data on the PHY link status and provides link down reasons and additional link related information.
        * Enabled TX configuration response and movement during Link Training in Ethernet.
        * Added support at lane rate of 12.89Gb.
        * Limits the amount of time a packet may head a Traffic Class (TC) transmission queue, without being transmitted. Stale packets are discarded. Active by default for TCs adhering to link level flow control.
        * UAR page size currently is set to 4KB and not according to what the system page size determines.
        * Improved performance of:  
       Doorbell from User Access Region (UAR)  
       Clear interrupt from User Access Region (UAR)
      
        * Added support for additional transport counters.
        * Added ODP support for DC.
        * Enabled scatter-to-CQE for sent packets for DC.
        * Enabled moderation period modification in CQ modify command.
        * Added support for minimum/maximum rate limit per vport in SR-IOV.
        * Enabled network traffic between UEFI-Shell and OS.
        * Enabled the PF to force disable RoCE for its VFs.
        * Added 2 new access registers:  
       Management Capabilities Mask Register  
       Ports CApabilities Mask Register Fields  
      For further information, please refer to the PRM.
      
        * Enabled VNIC the control to enable/disable its local loopback traffic.
        * Added the option to open a receive RDMA Flow Table and to forward RoCE traffic to some destination QP.
        * Added support for Multi-Host LID base routing. This feature requires a new OpenSM (v4.7.1 and above which comes with MLNX_OFED 3.3-2.0.0.0) with the following attributes:  
       qos TRUE  
       lmc 2 (if there is no quad host in the fabric, you can set the lmc to 1)  
       virt_enabled 2 Note: Multi-Host LID base routing can be configured by the
      INI only. The default is 0
      
        * Resilient RoCE is the ability to send RoCE traffic over a lossy network (a network without flow control enabled), without the need to enable flow control on the network. The ability is accomplished by enabling ECN on both the Switch and the Host.
        * Enables load balancing in the Multi PF Switch layer (MPFS) based on the L3/L4 headers
        * Increased the number of VFs from 64 to 95 per Physical Function (PF). Note: When increasing the number of VFs, the following limitations must be taken into consideration: server_total_bar_size >= (num_pfs)*(2log_pf_uar_bar_- size + 2log_vf_uar_bar_size*total_vfs) server_total_msix >= (num_pfs)*(num_pf_msix + num_vfs_msix *total_vfs) Note: For the maximum number of VFs supported by your driver, please refer to your drivers' Release Notes or User Manual.
        * Added support for Port Flap Counter.
        * Limits the buffer size for all entries to improve performance. KSM is used when associating Key Length My Virtual Address (KLMs) with fixed memory size.
        * This entry (null_mkey) is use to indicate non-present KLM/KSM entries. When accessing is, it causes the device to generate page fault event.
        * PLDM firmware burning is based on the DMTF spec DSP0267 (draft 9). The feature enables upgrading firmware and expansion ROM images using the PLDM protocol over MCTP (over PCIe). By doing so, a supporting BMC can query and upgrade the firmware without using OS based tools.
        * Added a new physical layer statistics counters group. The new group includes BER counters, FEC error correction, clear time, and additional physical layer counters. For further information, please refer to the Ethernet Adapters Programming Manual (PRM).
        * Enables the user to set a certain link up state for an unlimited period of time. This mode has 3 states:  
       Aux power (standby)  
       Reboot/boot/driver unloaded - the server is active and no driver is up  
       Driver is up - at least one driver is up (the time between init HCA and
      teardown or FLR)
      
        * Added support for Doorbell from User Access Region (UAR).
        * [Beta] Added support for maximum rate limit per function in SR-IOV.
        * Allows the user to configure the adapter card to stop sending pauses after x when the receive port is unavailable (in a hang state).
        * [Beta] Added support for new performance counters.
        * DCBX is used by DCB devices to exchange configuration information with directly connected peers. DCBX uses Link Layer Discovery Protocol (LLDP) to exchange parameters between two link peers. For further information, please refer to the PRM.
        * Allows network port registers to revert to their default values when the driver is restarted or the host is rebooted.
        * Added additional network link up modes. The new modes decide when to keep the network link up. The new modes are:  
       keep_eth_link_up  
       keep_ib_link_up  
       keep_link_up_on_boot  
       keep_link_up_on_standby
      
        * Added v1, v3, v6 tags to VPD read only tag
        * Enables software to scatter or strip FCS in RQ.
        * Keeps track of the creation of a packet. A time-stamping service supports assertions of proof that a datum existed before a particular time. 
        * Applies pause functionality to specific classes of traffic on the Ethernet link.
        * Custom port counters provide the user a clear indication about RDMA send/receive statistics and errors
        * The Link Layer Discovery Protocol (LLDP) is a vendor-neutral Link Layer protocol in the Internet Protocol Suite used by network devices for advertising their identity, capabilities, and neighbors on a IEEE 802 LAN. The protocol is formally defined in IEEE 802.1AB.
        * ConnectX-4 adapters now support 1Gb/s and 56GbE Ethernet connectivity in addition to 10GigE, 25GigE, 40GigE, 50GigE, and 100GigE.
        * Provides a clear indication of Flow Steering statistics and errors.
        * The minimal amount of packet headers inlined in the WQE's Eth Segment.
        * A flow table may include a table-miss flow entry, which renders all Match Fields wildcards. If a packet does not match a flow entry in a flow table, this is a table miss. The behavior on a table miss depends on the table configuration. A table-miss flow entry in the flow table may specify how to process unmatched packets.
        * Single Root IO Virtualization (SR-IOV) is a technology that allows a physical PCIe device to present itself multiple times through the PCIe bus.
        * Uses the HCA for offloading erasure coding calculations.
        * Enables the administrator to add a timestamp to the firmware they want to upgrade to avoid situations where one host tries to upgrade the firmware and another tries to downgrade; which may lead to two or more unnecessary server reboots. For further information, please refer to MFT User Manual.
        * The change includes the following:  
      1\. Changed port configuration which required link re-training (such as speed)  
      2\. PAOS down  
      3\. PAOS up  
      This change, will cause the link to toggle and new configurations to take
      effect.
      
        * Flint utility allows performing an MD5 checksum on the non-persistent sections of the firmware image. For further information, please refer to MFT User Manual.
        * Improved TX signal integrity for Electromagnetic Induction (EMI) compliance.
        * Optic modules thermal sensing - Enables the firmware to read and report the temperature of the module.
        * PLDM for module thermal sensing - Supports platform-level data models and platform functions in a platform management subsystem. PLDM is designed to be an effective interface and data model that provides efficient access to low-level platform inventory, monitoring, control, event, and data/parameters transfer functions.
        * Low power boot state - Enables u-boot to put non-boot CPUs into a low power status. To enable low power boot using iLO debugger use the following commands.  
                            * Port shutdown due to optic thermal event - Enables the firmware to close the power cage in case of high temperature in the module.
        * Reduced the port link-up time when negotiating according to Clause 73 (DME)
        * Large Receive Offload (LRO)  Large Send Offload (LSO)
        * Receive Side Scaling (RSS)
        * Global Pause  RoCEv1.0/RoCEv2.0
        * Flow Steering
        * Sniffer Ethernet
        * Rate Limiter (at Beta level)
        * Multi packet WQE
        * Enhanced Transmission Selection standard (ETS)
        * Explicit Congestion Notification (ECN)
        * Priority Flow Control (PFC)
        * CQE time stamping
        * PCIe Function Level Reset (FLR)
        * Power Management L2/L3 flow support
        * Strided SRQ
        * Self Loopback support
        * Transport Domain support
        * CQ2EQ remapping
        * Added support for the following commands:  
       MODIFY/QUERY_ESW_VPORT_CONTEXT  
       QUERY/MODIFY_CONG_STATUS  
       QUERY/MODIFY_CkONG_PARAMS  
       QUERY_CONG_STATISTICS  
       ADD/DELETE_VXLAN_UDP_DPORT


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.5-2.1
changelog:
  -     *Fixes in 2.40.5030:**
      
        * Fixed a race between the firmware and the hardware during driver start which blocked outbound completions.
        * Fixed an issue which caused the firmware not to send link_down event to the driver when running the close_port command.
        * Fixed an issue where in rare cases the Auto Sense failed to detect the right protocol.
        * Fixed signal integrity issue when connecting a WCS ConnectX4 mezz card to Pikes peak FPGA..
        * Added the option to transmit corrupted DME pages for a very short period of time at the beginning of the Auto-Negotiation flow.
        * Fixed an incorrect report of the PortRcvDataVLExtended / PortXmitDataVLExtended counters by the firmware.
        * Fixed a rare issue which caused firmware's packet injector to cut off packets when the TX was congested.
        * Fixed an issue that caused the response to TX requests to take up to 10 mili-seconds in IEEE clause 72 Link Training.
        * Fixed a race between 2 iriscs which caused a QP to get stuck in burst control limit state.
        * When a QP was in error state, the firmware generated too many err CQEs at once, thus causing the cmdif responsiveness to be too slow. To prevent the above, the number of err CQEs was limited to 16 at a time.
        * Fixed an issue that caused the MAC address that was set from the OS using ifconfig to be not reflected in the OCBB buffer.
        * Fixed an issue where the ibdump got broken when running with loopback traffic.
        * Fixed an issue where the firmware took QP to firmware ownership and then released it to the hardware ownership without checking if another firmware flow owns the same QP.
        * Fixed an issue which occurred after disconnecting cable which showed the link type as IB even if the link type of the port is ETH.
        * Fixed an issue related to the HCA PoerXmitWait counter on port 2 (connected to port 2 on Switch-IB) where it started counting and reached 0xFF's regardless of connection to switch.
        * Fixed a completion error issue when ECN was enabled. The ECN usage caused ordering errors in completion queues (CQ).
        * Fixed the length calculation of UDP. The incorrect UDP length in the CNP packet caused miss-calculation of the ICRC.
        * Fixed a wrong returned status in cable info MAD when the cable was not connected
        * Fixed failure instances when initiating FLR in the Physical Function.
        * Disabled High Rate Steering mode in the INI to enable its compatibility with NC-SI over VLAN.
        * Fixed a default hardware configuration issue which caused RDP over IPv4 traffic to be dropped.
        * MLNX_OEM command GET_TEMP returned a wrong value in the max_temp field.
        * Fixed an issue which caused TX traffic to stop when the message MTU size was larger than QP.mtu.
        * Fixed an issue which caused NVCONFIG to fail when the number of sector was set to 1 and the sector was zeroed.
        * Fixed a race in handling a duplicated "read request from middle".
        * Fixed an issue which caused lack of IB traffic on SR-IOV VPI.
        * Fixed an issue which caused NVRAM to get stuck when it filled non-valid information in TLV.
        * Fixed an issue which caused an internal firmware error when APM changed the QPs port mapping. 
        * Fixed an issue which caused a firmware internal error when handling QP alternative context. 
        * Fixed an issue which caused packet transmission to get stuck when the software tried to send pause frames with dmac equal to one of the device's MAC addresses.
        * Fixed a wrong reporting of section 5 event 8 - LSO support.
        * Fixed a mistakenly dropped ETH packet with ethertype 0x600 by the NIC.
        * Fixed a case preventing broadcast traffic from arriving to their destination after detaching high priority broadcast rule on a port where NC-SI was enabled.
        * Fixed an issue where the port raised as SDR vs. InfiniScale IV QDR Switch
        * Fixed a rare case of completion Error with Bad Opcode sequence status which occurred when retransmitting read requests
        * Fixed a case where the actual bandwidth did not match the user settings in VM QoS.
        * Fixed a case where on rare cases, communication to BMC was lost during driver initialization.
        * Fixed an issue with cable reading, which caused the link not to raise.
        * Set the maximum EQN number to 1024.
        * Fixed a rare issue with VPD init flow which caused read failures.
        * Fixed an issue with RX size counter not being reported.
        * Fixed promiscuous mode compatibility with A0-DMFS steering.
        * Fixed promiscuous mode compatibility when NC-SI is enabled and configured.
        * Fixed sending/receiving OEM temp commands (set/get) with channel ID 0x1f failure.
        * Fixed an issue which caused packets to drop on a port when changing the interface state of the other port.
        * Fixed long management communication loss and SOL hang during reboot cycles.
        * Fixed wrong processing of inbound traffic towards BMC which caused communication loss.
        * Fixed management link loss upon closing port interface through the driver.
        * Fixed a false indication in firmware of an expander presence causing delay in EEPROM reading.
        * Fixed an issue which caused a link down on a port when the cable was removed from the other port.
        * Fixed a rare case where packet with length zero got stuck in hardware queues.
        * Fixed an issue which caused InfiniBand congestion control packet (CNP) to hang in hardware.
        * Fixed an issue which caused AEN to be sent after channel reset.
        * Fixed an issue which prevented the restoring of QoS setting to its default consequently causing bandwidth degradation.
        * Fixed an occasional long link up time with 10GbE based devices.
        * Fixed an issue preventing cable readings from i2c slave address 0x51
        * Fixed a wrong parity bit calculation when transmitting PCIe TS1 packets.
        * Fixed a possible deadlock in PM turnoff request transmission and ack acceptance flow.
        * Fixed a rare case with alignments state machines which caused occasional width degradation.
        * Fixed an issue where the transmit queues hanged while congestion control was enabled and operational (EQC/QCN)
        * Fixed an unexpected work completion syndrome with vendor syndrome 0x77 received when running RDMA SEN/WRITE traffic with retransmissions.
        * Fixed an issue which caused SetPortInfo to return a good status when receiving invalid LinkSpeedEnabled value.
        * Fixed an issue which caused dual port SFPP module cards to be automatically mapped with expander.
        * Fixed an issue where firmware overrides the steering mode that was chosen by the driver.
        * Fixed invalid return sensing results occurred when the link was up.
        * Fixed an issue causing the sensing result to be delayed when cable was unplugged.
        * Fixed an issue causing the link type to be displayed as ETH when set to AUTO.
        * Fixed an issue causing ARP not to reply when connected to Hyper-V vSwitch.
      
      **Fixes in 14.18.2030****:**
      
        * On rare occasions during UEFI boot cycles system got stuck while WinPE is loaded. (OS WinPE, system DL160).
        * Single FTE that catches both untagged and prio-tagged packets (by giving an FTE with match_value.vlan_tag = 0 and match_value.vid = 0) is currently not supported.
        * Flashing the firmware requires server reboot. Firmware cannot be flashed twice without server reboot after first flashing
        * If the vport state is DOWN and a packet is sent in local loopback, the sx_sniffer tool will not function.
        * Fixed an issue causing bubbles to appear as symbol errors when link raised FDR 1x.
        * When Clause 74 Fire-Code FEC is active, and there are FC corrected errors, both the FC_correctable counter and the FC_uncoreectable counter are increment.
        * Some Port Control Register do not return to the default value after the last port owner host restarts the driver.
        * Fixed an issue which caused RX to hang when the UDP packet had a reserved UDP destination port.
        * Fixed DMAC reporting mapping per host.
        * Fixed an EEH error from PCI which caused firmware to hang.
        * Fixed the default value of the PCIe target_link_speed to Gen3 in link control2.
        * Fixed an issue which prevented LEDs from blinking when the traffic was less than 0.1% of the link speed.
        * Fixed an issue which caused the mlxconfig configuration of VF_LOG_BAR_SIZE to be ignored and to be set to 5 (32MB).
        * A server getting into a Standby mode while Packet-Pacing is enabled might cause firmware to hang and driver call-trace.
        * Fixed an issue which caused unexpected QoS functionality in case of multiple sources to single destination traffic transmission.
        * Fixed an issue which occasionally caused the RX traffic to hang in DC when received a PCI error on WQE fetch.
        * Fixed OOB connection issue during Intel's ITP inject errors test.
        * Fixed an issue which prevented MAC address changes by to driver to be reflected in the OBCC and NC-SI interfaces.
        * Added protection from IOPX thermal diode destabilization to prevent UEFI IPv6 PXE boot failure on ConnectX-4 Lx 25GE cards.
        * Fixed an issue which caused a link down in Port 2 when unplugging the cable from Port 1.
        * In some cases, a Bit Error Rate is not optimal on 10G/40G links.
        * Instability of Link Training Flow occurs during 100G Auto-Negotiation.
        * Fixed a rare issue which caused the command to hang when moved the QP to RESET and back to RTS.
        * Improved RDMA READ bandwidth under packet lost scenario.
        * Added support for pnat = 1 in HCA access_reg command as required by the ibdiagnet tool.
        * Fixed the LLDP OCBB response: return value is now ascii.
        * Fixed a very rare NMI issue during PXE cycles.
        * Increased the steering hash tables static size from 128 to a maximum of 32K entries.
        * Prevented miscalculation of module temperature when using 100Gb/s cables (OPN: MFA1A00-Cxxx for 100GbE).
        * Reduced one hop for Unicast RX steering, steering pipes balancing.
        * Non-volatile configuration of Port Type TLV more than 50 times might cause system hang.
        * Enabled RoCE IPv4 Multicast. This prevents MCG command from failing when an IPv4 is mapped to an IPv6 address.
        * If the PF driver or the tool (e.g. ethtool) use PAOS DOWN command (e.g. by ifconfig down or ip link set down), loopback traffic is blocked for all functions on this port (PF<->VFs / VF<->VF) In Multihost loopback, the traffic will be blocked once the firmware receives the PAOS down command from all PFs. However, the loopback traffic will not be blocked when the port is down  due to the physical link (for example: cable plugged out, switch port down).
        * Fixed a 25G and 50G link issue when Clause 91 RS FEC was active.
        * Added a missing invalidation of eSwitch cache upon FLR which caused the upcoming driver load to either fail or not to be able to transmit.
        * Fixed a UEFI IPv6 PXE boot failure on ConnectX-4 Lx 25GbE OCP card.
        * Fixed an issue which prevented Vport counters from counting local loopback packets. Packets now are filter by the self-loopback prevention.
        * Reported INTx as unsupported to allow PFs Passthrough on PowerKVM.
        * SR-IOV Ethernet supports up to 18 VFs per port only.
        * Fixed and incident what allowed local (internal) loopbacked packets to be counted by the Vport counters, although Vport counters should count only traffic that crosses the Vport.
        * Fixed an issue preventing driver loading or TX traffic sending upon reboot, after ungraceful driver unload.
        * Fixed casting of BMC MAC before steering API.
        * Fixed the PCI write flow to take into consideration the PCI MTU. This fix eliminates the need for NOPs in the flow, which resulted from PPC larger PCI MTU.  
      The single queue limitation for READ is due to a hardware limitation of the
      number of READ request in a given time.
      
        * Fixed a case that caused FlexBoot to not work as expected with systems that run with "large bar" enabled (Above 4G Decoding) over Connect-IB or ConnectX-4 HCAs.
        * Fixed an issue which prevented link creation when connected to IXIA 25G.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.5-4.1
changelog:
  -     *Firmware for the following devices are updated to 2.40.7000:**  
        
      779799-B21 (HP Ethernet 10G 2-port 546FLR-SFP+ Adapter)  
      779793-B21 (HP Ethernet 10G 2-port 546SFP+ Adapter)
      
      **New features and changes in version 2.40.7000:**
      
        * Added Etherent Link down counter.
        * Enables steering packets to receive queues according to Ethertype matching 
        * Adds support for additional rate values. 
        * Counters that count the number of repeated Send WQE cache lookups that resulted in a miss.
        * Flint utility allows performing an MD5 checksum on the non-persistent sections of the firmware image.
        * New performance and back-pressure counters command via PRM (For further information, please refer to the PRM)
        * Support for Multicast/Unicast sniffer rules (For further information, please refer to the PRM)
        * Support for VLAN in VLAN encapsulation (For further information, please refer to the PRM)
        * CQ creation offload by software
        * Support for rst2rts command
        * Invalidates a TLV during the firmware boot stage
        * A new counter for the diag_rprt PRM command to count packet drops due to noreceive buffer
        * Support for Ethernet TX lifetime cycle control (Head of Queue)
        * A new register (PPLR) that allows egress and external loopback control (For further information, please refer to the PRM)
        * A watchdog mechanism to track ingress traffic stalls to prevent flooding the network with Flow Control packets
        * Inspur LED scheme: A new LED scheme controlled by the INI which causes constant traffic LED indication even without traffic.
        * Added support for multiple RoCE modes (RoCE v1+v2) on the same port: RoCE mode is per connection now.
        * Added a new QP command "INIT2RTS_QP" to enhance QP connection readiness time.
        * Disabled FCS checks to support switches that replace FCS with Timestamp.
        * Added RX Port identification for direct rout packets.
        * Improved RDMA WRITE/SEND performance with retransmissions.
        * Enabled firmware burning/querying using the PRM ACCESS_REG command.
        * Added support for VAM.  Enabled bad cable EEPROM reporting to the driver.
        * Added support for Platform Level Data Model (PLDM) sideband protocol.
        * Added support for priority based A0-DMFS mode (For further information, please refer to the PRM).
        * Added support for Unicast/Multicast loopback disablement by the driver. (For further information, please refer to the PRM)
        * Removed the source IP from the hash calculation (For further information, please refer to the PRM)
        * Added support for Inline Receive mode up to 2KB.
        * Added support for multiple RoCE modes (RoCE v1+v2) on the same port: RoCE mode is per connection now.
        * Added a new QP command "INIT2RTS_QP" to enhance QP connection readiness time.
        * Disabled FCS checks to support switches that replace FCS with Timestamp.
        * Added RX Port identification for direct rout packets.
        * Improved RDMA WRITE/SEND performance with retransmissions.
        * Enabled firmware burning/querying using the PRM ACCESS_REG command.
        * Added support for VAM.  Enabled bad cable EEPROM reporting to the driver.
        * Added support for Platform Level Data Model (PLDM) sideband protocol.
        * Added support for priority based A0-DMFS mode (For further information, please refer to the PRM).
        * Added support for Unicast/Multicast loopback disablement by the driver. (For further information, please refer to the PRM)
        * Removed the source IP from the hash calculation (For further information, please refer to the PRM)
        * Added support for Inline Receive mode up to 2KB.
        * Sideband moved to port 0
        * Added MCTP command support
        * Changed the HP LED scheme for the 779799-B21 adapter.
      
      **Firmware for the following devices are updated to 14.18.2030****:**
      
      817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)  
      817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
        * Added logical link indication in SFP to BaseT modules and disabled logical link when peer port is down.
        * Added support for 10GbE in 25GbE SFP optical modules.
        * Enables mlxlink tool to collect data on the PHY link status and provides link down reasons and additional link related information.
        * Enabled TX configuration response and movement during Link Training in Ethernet.
        * Added support at lane rate of 12.89Gb.
        * Limits the amount of time a packet may head a Traffic Class (TC) transmission queue, without being transmitted. Stale packets are discarded. Active by default for TCs adhering to link level flow control.
        * UAR page size currently is set to 4KB and not according to what the system page size determines.
        * Improved performance of:  
       Doorbell from User Access Region (UAR)  
       Clear interrupt from User Access Region (UAR)
      
        * Added support for additional transport counters.
        * Added ODP support for DC.
        * Enabled scatter-to-CQE for sent packets for DC.
        * Enabled moderation period modification in CQ modify command.
        * Added support for minimum/maximum rate limit per vport in SR-IOV.
        * Enabled network traffic between UEFI-Shell and OS.
        * Enabled the PF to force disable RoCE for its VFs.
        * Added 2 new access registers:  
       Management Capabilities Mask Register  
       Ports CApabilities Mask Register Fields  
      For further information, please refer to the PRM.
      
        * Enabled VNIC the control to enable/disable its local loopback traffic.
        * Added the option to open a receive RDMA Flow Table and to forward RoCE traffic to some destination QP.
        * Added support for Multi-Host LID base routing. This feature requires a new OpenSM (v4.7.1 and above which comes with MLNX_OFED 3.3-2.0.0.0) with the following attributes:  
       qos TRUE  
       lmc 2 (if there is no quad host in the fabric, you can set the lmc to 1)  
       virt_enabled 2 Note: Multi-Host LID base routing can be configured by the
      INI only. The default is 0
      
        * Resilient RoCE is the ability to send RoCE traffic over a lossy network (a network without flow control enabled), without the need to enable flow control on the network. The ability is accomplished by enabling ECN on both the Switch and the Host.
        * Enables load balancing in the Multi PF Switch layer (MPFS) based on the L3/L4 headers
        * Increased the number of VFs from 64 to 95 per Physical Function (PF). Note: When increasing the number of VFs, the following limitations must be taken into consideration: server_total_bar_size >= (num_pfs)*(2log_pf_uar_bar_- size + 2log_vf_uar_bar_size*total_vfs) server_total_msix >= (num_pfs)*(num_pf_msix + num_vfs_msix *total_vfs) Note: For the maximum number of VFs supported by your driver, please refer to your drivers' Release Notes or User Manual.
        * Added support for Port Flap Counter.
        * Limits the buffer size for all entries to improve performance. KSM is used when associating Key Length My Virtual Address (KLMs) with fixed memory size.
        * This entry (null_mkey) is use to indicate non-present KLM/KSM entries. When accessing is, it causes the device to generate page fault event.
        * PLDM firmware burning is based on the DMTF spec DSP0267 (draft 9). The feature enables upgrading firmware and expansion ROM images using the PLDM protocol over MCTP (over PCIe). By doing so, a supporting BMC can query and upgrade the firmware without using OS based tools.
        * Added a new physical layer statistics counters group. The new group includes BER counters, FEC error correction, clear time, and additional physical layer counters. For further information, please refer to the Ethernet Adapters Programming Manual (PRM).
        * Enables the user to set a certain link up state for an unlimited period of time. This mode has 3 states:  
       Aux power (standby)  
       Reboot/boot/driver unloaded - the server is active and no driver is up  
       Driver is up - at least one driver is up (the time between init HCA and
      teardown or FLR)
      
        * Added support for Doorbell from User Access Region (UAR).
        * [Beta] Added support for maximum rate limit per function in SR-IOV.
        * Allows the user to configure the adapter card to stop sending pauses after x when the receive port is unavailable (in a hang state).
        * [Beta] Added support for new performance counters.
        * DCBX is used by DCB devices to exchange configuration information with directly connected peers. DCBX uses Link Layer Discovery Protocol (LLDP) to exchange parameters between two link peers. For further information, please refer to the PRM.
        * Allows network port registers to revert to their default values when the driver is restarted or the host is rebooted.
        * Added additional network link up modes. The new modes decide when to keep the network link up. The new modes are:  
       keep_eth_link_up  
       keep_ib_link_up  
       keep_link_up_on_boot  
       keep_link_up_on_standby
      
        * Added v1, v3, v6 tags to VPD read only tag
        * Enables software to scatter or strip FCS in RQ.
        * Keeps track of the creation of a packet. A time-stamping service supports assertions of proof that a datum existed before a particular time. 
        * Applies pause functionality to specific classes of traffic on the Ethernet link.
        * Custom port counters provide the user a clear indication about RDMA send/receive statistics and errors
        * The Link Layer Discovery Protocol (LLDP) is a vendor-neutral Link Layer protocol in the Internet Protocol Suite used by network devices for advertising their identity, capabilities, and neighbors on a IEEE 802 LAN. The protocol is formally defined in IEEE 802.1AB.
        * ConnectX-4 adapters now support 1Gb/s and 56GbE Ethernet connectivity in addition to 10GigE, 25GigE, 40GigE, 50GigE, and 100GigE.
        * Provides a clear indication of Flow Steering statistics and errors.
        * The minimal amount of packet headers inlined in the WQE's Eth Segment.
        * A flow table may include a table-miss flow entry, which renders all Match Fields wildcards. If a packet does not match a flow entry in a flow table, this is a table miss. The behavior on a table miss depends on the table configuration. A table-miss flow entry in the flow table may specify how to process unmatched packets.
        * Single Root IO Virtualization (SR-IOV) is a technology that allows a physical PCIe device to present itself multiple times through the PCIe bus.
        * Uses the HCA for offloading erasure coding calculations.
        * Enables the administrator to add a timestamp to the firmware they want to upgrade to avoid situations where one host tries to upgrade the firmware and another tries to downgrade; which may lead to two or more unnecessary server reboots. For further information, please refer to MFT User Manual.
        * The change includes the following:  
      1\. Changed port configuration which required link re-training (such as speed)  
      2\. PAOS down  
      3\. PAOS up  
      This change, will cause the link to toggle and new configurations to take
      effect.
      
        * Flint utility allows performing an MD5 checksum on the non-persistent sections of the firmware image. For further information, please refer to MFT User Manual.
        * Improved TX signal integrity for Electromagnetic Induction (EMI) compliance.
        * Optic modules thermal sensing - Enables the firmware to read and report the temperature of the module.
        * PLDM for module thermal sensing - Supports platform-level data models and platform functions in a platform management subsystem. PLDM is designed to be an effective interface and data model that provides efficient access to low-level platform inventory, monitoring, control, event, and data/parameters transfer functions.
        * Low power boot state - Enables u-boot to put non-boot CPUs into a low power status. To enable low power boot using iLO debugger use the following commands.  
                            * Port shutdown due to optic thermal event - Enables the firmware to close the power cage in case of high temperature in the module.
        * Reduced the port link-up time when negotiating according to Clause 73 (DME)
        * Large Receive Offload (LRO)  Large Send Offload (LSO)
        * Receive Side Scaling (RSS)
        * Global Pause  RoCEv1.0/RoCEv2.0
        * Flow Steering
        * Sniffer Ethernet
        * Rate Limiter (at Beta level)
        * Multi packet WQE
        * Enhanced Transmission Selection standard (ETS)
        * Explicit Congestion Notification (ECN)
        * Priority Flow Control (PFC)
        * CQE time stamping
        * PCIe Function Level Reset (FLR)
        * Power Management L2/L3 flow support
        * Strided SRQ
        * Self Loopback support
        * Transport Domain support
        * CQ2EQ remapping
        * Added support for the following commands:  
       MODIFY/QUERY_ESW_VPORT_CONTEXT  
       QUERY/MODIFY_CONG_STATUS  
       QUERY/MODIFY_CkONG_PARAMS  
       QUERY_CONG_STATISTICS  
       ADD/DELETE_VXLAN_UDP_DPORT


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.5-4.1
changelog:
  -     *Fixes in 2.40.7000:**
      
        * Fixed a race between the firmware and the hardware during driver start which blocked outbound completions.
        * Fixed an issue which caused the firmware not to send link_down event to the driver when running the close_port command.
        * Fixed an issue where in rare cases the Auto Sense failed to detect the right protocol.
        * Fixed signal integrity issue when connecting a WCS ConnectX4 mezz card to Pikes peak FPGA..
        * Added the option to transmit corrupted DME pages for a very short period of time at the beginning of the Auto-Negotiation flow.
        * Fixed an incorrect report of the PortRcvDataVLExtended / PortXmitDataVLExtended counters by the firmware.
        * Fixed a rare issue which caused firmware's packet injector to cut off packets when the TX was congested.
        * Fixed an issue that caused the response to TX requests to take up to 10 mili-seconds in IEEE clause 72 Link Training.
        * Fixed a race between 2 iriscs which caused a QP to get stuck in burst control limit state.
        * When a QP was in error state, the firmware generated too many err CQEs at once, thus causing the cmdif responsiveness to be too slow. To prevent the above, the number of err CQEs was limited to 16 at a time.
        * Fixed an issue that caused the MAC address that was set from the OS using ifconfig to be not reflected in the OCBB buffer.
        * Fixed an issue where the ibdump got broken when running with loopback traffic.
        * Fixed an issue where the firmware took QP to firmware ownership and then released it to the hardware ownership without checking if another firmware flow owns the same QP.
        * Fixed an issue which occurred after disconnecting cable which showed the link type as IB even if the link type of the port is ETH.
        * Fixed an issue related to the HCA PoerXmitWait counter on port 2 (connected to port 2 on Switch-IB) where it started counting and reached 0xFF's regardless of connection to switch.
        * Fixed a completion error issue when ECN was enabled. The ECN usage caused ordering errors in completion queues (CQ).
        * Fixed the length calculation of UDP. The incorrect UDP length in the CNP packet caused miss-calculation of the ICRC.
        * Fixed a wrong returned status in cable info MAD when the cable was not connected
        * Fixed failure instances when initiating FLR in the Physical Function.
        * Disabled High Rate Steering mode in the INI to enable its compatibility with NC-SI over VLAN.
        * Fixed a default hardware configuration issue which caused RDP over IPv4 traffic to be dropped.
        * MLNX_OEM command GET_TEMP returned a wrong value in the max_temp field.
        * Fixed an issue which caused TX traffic to stop when the message MTU size was larger than QP.mtu.
        * Fixed an issue which caused NVCONFIG to fail when the number of sector was set to 1 and the sector was zeroed.
        * Fixed a race in handling a duplicated "read request from middle".
        * Fixed an issue which caused lack of IB traffic on SR-IOV VPI.
        * Fixed an issue which caused NVRAM to get stuck when it filled non-valid information in TLV.
        * Fixed an issue which caused an internal firmware error when APM changed the QPs port mapping. 
        * Fixed an issue which caused a firmware internal error when handling QP alternative context. 
        * Fixed an issue which caused packet transmission to get stuck when the software tried to send pause frames with dmac equal to one of the device's MAC addresses.
        * Fixed a wrong reporting of section 5 event 8 - LSO support.
        * Fixed a mistakenly dropped ETH packet with ethertype 0x600 by the NIC.
        * Fixed a case preventing broadcast traffic from arriving to their destination after detaching high priority broadcast rule on a port where NC-SI was enabled.
        * Fixed an issue where the port raised as SDR vs. InfiniScale IV QDR Switch
        * Fixed a rare case of completion Error with Bad Opcode sequence status which occurred when retransmitting read requests
        * Fixed a case where the actual bandwidth did not match the user settings in VM QoS.
        * Fixed a case where on rare cases, communication to BMC was lost during driver initialization.
        * Fixed an issue with cable reading, which caused the link not to raise.
        * Set the maximum EQN number to 1024.
        * Fixed a rare issue with VPD init flow which caused read failures.
        * Fixed an issue with RX size counter not being reported.
        * Fixed promiscuous mode compatibility with A0-DMFS steering.
        * Fixed promiscuous mode compatibility when NC-SI is enabled and configured.
        * Fixed sending/receiving OEM temp commands (set/get) with channel ID 0x1f failure.
        * Fixed an issue which caused packets to drop on a port when changing the interface state of the other port.
        * Fixed long management communication loss and SOL hang during reboot cycles.
        * Fixed wrong processing of inbound traffic towards BMC which caused communication loss.
        * Fixed management link loss upon closing port interface through the driver.
        * Fixed a false indication in firmware of an expander presence causing delay in EEPROM reading.
        * Fixed an issue which caused a link down on a port when the cable was removed from the other port.
        * Fixed a rare case where packet with length zero got stuck in hardware queues.
        * Fixed an issue which caused InfiniBand congestion control packet (CNP) to hang in hardware.
        * Fixed an issue which caused AEN to be sent after channel reset.
        * Fixed an issue which prevented the restoring of QoS setting to its default consequently causing bandwidth degradation.
        * Fixed an occasional long link up time with 10GbE based devices.
        * Fixed an issue preventing cable readings from i2c slave address 0x51
        * Fixed a wrong parity bit calculation when transmitting PCIe TS1 packets.
        * Fixed a possible deadlock in PM turnoff request transmission and ack acceptance flow.
        * Fixed a rare case with alignments state machines which caused occasional width degradation.
        * Fixed an issue where the transmit queues hanged while congestion control was enabled and operational (EQC/QCN)
        * Fixed an unexpected work completion syndrome with vendor syndrome 0x77 received when running RDMA SEN/WRITE traffic with retransmissions.
        * Fixed an issue which caused SetPortInfo to return a good status when receiving invalid LinkSpeedEnabled value.
        * Fixed an issue which caused dual port SFPP module cards to be automatically mapped with expander.
        * Fixed an issue where firmware overrides the steering mode that was chosen by the driver.
        * Fixed invalid return sensing results occurred when the link was up.
        * Fixed an issue causing the sensing result to be delayed when cable was unplugged.
        * Fixed an issue causing the link type to be displayed as ETH when set to AUTO.
        * Fixed an issue causing ARP not to reply when connected to Hyper-V vSwitch.
      
      **Fixes in 14.18.2030****:**
      
        * On rare occasions during UEFI boot cycles system got stuck while WinPE is loaded. (OS WinPE, system DL160).
        * Single FTE that catches both untagged and prio-tagged packets (by giving an FTE with match_value.vlan_tag = 0 and match_value.vid = 0) is currently not supported.
        * Flashing the firmware requires server reboot. Firmware cannot be flashed twice without server reboot after first flashing
        * If the vport state is DOWN and a packet is sent in local loopback, the sx_sniffer tool will not function.
        * Fixed an issue causing bubbles to appear as symbol errors when link raised FDR 1x.
        * When Clause 74 Fire-Code FEC is active, and there are FC corrected errors, both the FC_correctable counter and the FC_uncoreectable counter are increment.
        * Some Port Control Register do not return to the default value after the last port owner host restarts the driver.
        * Fixed an issue which caused RX to hang when the UDP packet had a reserved UDP destination port.
        * Fixed DMAC reporting mapping per host.
        * Fixed an EEH error from PCI which caused firmware to hang.
        * Fixed the default value of the PCIe target_link_speed to Gen3 in link control2.
        * Fixed an issue which prevented LEDs from blinking when the traffic was less than 0.1% of the link speed.
        * Fixed an issue which caused the mlxconfig configuration of VF_LOG_BAR_SIZE to be ignored and to be set to 5 (32MB).
        * A server getting into a Standby mode while Packet-Pacing is enabled might cause firmware to hang and driver call-trace.
        * Fixed an issue which caused unexpected QoS functionality in case of multiple sources to single destination traffic transmission.
        * Fixed an issue which occasionally caused the RX traffic to hang in DC when received a PCI error on WQE fetch.
        * Fixed OOB connection issue during Intel's ITP inject errors test.
        * Fixed an issue which prevented MAC address changes by to driver to be reflected in the OBCC and NC-SI interfaces.
        * Added protection from IOPX thermal diode destabilization to prevent UEFI IPv6 PXE boot failure on ConnectX-4 Lx 25GE cards.
        * Fixed an issue which caused a link down in Port 2 when unplugging the cable from Port 1.
        * In some cases, a Bit Error Rate is not optimal on 10G/40G links.
        * Instability of Link Training Flow occurs during 100G Auto-Negotiation.
        * Fixed a rare issue which caused the command to hang when moved the QP to RESET and back to RTS.
        * Improved RDMA READ bandwidth under packet lost scenario.
        * Added support for pnat = 1 in HCA access_reg command as required by the ibdiagnet tool.
        * Fixed the LLDP OCBB response: return value is now ascii.
        * Fixed a very rare NMI issue during PXE cycles.
        * Increased the steering hash tables static size from 128 to a maximum of 32K entries.
        * Prevented miscalculation of module temperature when using 100Gb/s cables (OPN: MFA1A00-Cxxx for 100GbE).
        * Reduced one hop for Unicast RX steering, steering pipes balancing.
        * Non-volatile configuration of Port Type TLV more than 50 times might cause system hang.
        * Enabled RoCE IPv4 Multicast. This prevents MCG command from failing when an IPv4 is mapped to an IPv6 address.
        * If the PF driver or the tool (e.g. ethtool) use PAOS DOWN command (e.g. by ifconfig down or ip link set down), loopback traffic is blocked for all functions on this port (PF<->VFs / VF<->VF) In Multihost loopback, the traffic will be blocked once the firmware receives the PAOS down command from all PFs. However, the loopback traffic will not be blocked when the port is down  due to the physical link (for example: cable plugged out, switch port down).
        * Fixed a 25G and 50G link issue when Clause 91 RS FEC was active.
        * Added a missing invalidation of eSwitch cache upon FLR which caused the upcoming driver load to either fail or not to be able to transmit.
        * Fixed a UEFI IPv6 PXE boot failure on ConnectX-4 Lx 25GbE OCP card.
        * Fixed an issue which prevented Vport counters from counting local loopback packets. Packets now are filter by the self-loopback prevention.
        * Reported INTx as unsupported to allow PFs Passthrough on PowerKVM.
        * SR-IOV Ethernet supports up to 18 VFs per port only.
        * Fixed and incident what allowed local (internal) loopbacked packets to be counted by the Vport counters, although Vport counters should count only traffic that crosses the Vport.
        * Fixed an issue preventing driver loading or TX traffic sending upon reboot, after ungraceful driver unload.
        * Fixed casting of BMC MAC before steering API.
        * Fixed the PCI write flow to take into consideration the PCI MTU. This fix eliminates the need for NOPs in the flow, which resulted from PPC larger PCI MTU.  
      The single queue limitation for READ is due to a hardware limitation of the
      number of READ request in a given time.
      
        * Fixed a case that caused FlexBoot to not work as expected with systems that run with "large bar" enabled (Above 4G Decoding) over Connect-IB or ConnectX-4 HCAs.
        * Fixed an issue which prevented link creation when connected to IXIA 25G.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.6
changelog:
  -     *Firmware for the following devices are updated to 2.42.5000:**  
        
      779799-B21 (HP Ethernet 10G 2-port 546FLR-SFP+ Adapter)  
      779793-B21 (HP Ethernet 10G 2-port 546SFP+ Adapter)
      
      **New features and changes in version 2.42.5000:**
      
        * Added support for the following features: 
          * TLV: CX3_GLOBAL_CONF to enable/disable timestamp on incoming packets through mlxconfig configuration.
          * User MAC configuration.
          * Automatically collecting mstdump before driver reset.
          * to detect DEAD_IRISC (plastic) from TPT (iron) and raise an assert.
        * Enhanced the debug ability for command timeout cases.
        * Added a new field to "set port" command which notifies the firmware what is the user_mtu size.
      
      **Firmware for the following devices are updated to 14.21.2800****:**
      
      817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)  
      817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
      **New features and changes in version 14.21.2800:**
      
        * Query vPort Environments (Debug Counters) - Debug counters are a group of counters that handle traffic performance issue related to firmware overhead in transport flow. The following are the additional counters added to this firmware version: 
          * current_q_under_processor_handle
          * total_q_under_processor_handle
          * qp_priority_update_flow


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.6
changelog:
  -     *Fixes submitted in version 2.42.5000:**
      
        * The PortRcvPkts counter was prevented from being cleared after resetting it.
        * Fixed an issue which caused a system Time Out on the configuration cycle of the VFs when more than 10 Virtual Functions performed FLR and the completion Time Out value was configured to a range of less than  
      16 msec.
      
        * Fixed an issue that caused the server to hang and result in NMI when running "mlxfwtop -d mt4103_pci_cr0" while restarting the driver in parallel (from a different thread). In this case, the downstream bridge over the device reported completion timeout error.
        * Fixed an issue in flow_steering where BMC could not receive a ping over IPV6 after running bmc_reboot.
        * Fixed an issue while closing the HCA, where RX packet caused bad access to resources that did not exist, and consequently caused the QPCGW or the irisc to get stuck.
        * Fixed an issue where the masterSM LID and the LID was either 0 or 0xFFFF when the port was neither active nor armed.
        * Fixed an issue that prevented ibdump from capturing all MADs packets.
        * Fixed an issue that prevented the link to go up after reboot.
        * Fixed a rare issue that cause the PCIe configuration cycle that arrived during the time of sw_reset to generate 2 completions.
        * Fixed an issue that caused NC-SI not to work when adding the disable_static_steering_ini field in the ini file, due to memory allocation issue for this field in the scratchpad.
      
      **Fixes submitted in version 14.21.2800:**
      
        * Fixed an issue that caused QP connection timeout due to firmware not being able to handle duplicate packets with AckReq bit set. The fix stopped ignoring duplicate AckReq packets to avoid timeout on the sender side.
        * MPFS load balance (DUP_MAC_ACTION==LOAD_BALANCE(1)) is not working as long as IB_ROUTING_MODE/SRIOV_IB_ROUTING_MODE is configured to LID.
        * Fixed an issue that caused a SX engine deadlock (the SX engine handles software port/priority changes for a specific Send Queue) when more than a single SX engine handled the "prio diff" flow simultaneously, thus caused the hardware to get stuck.  
      The issue happened as the firmware releases the SX engine and waits for
      various operation to complete. However, due to a race that allows a different
      transaction to get into the SX engine and cause the lock to be taken by it,
      the SX engine release is prevented.
      
        * Fixed an issue that caused the system to hang while changing QPTS/QPDPM/QPDP parameters during traffic.
        * Fixed unfairness between senders in RoCE LAG while ECN is configured.
        * Fixed an issue which displayed diagnostic counters only on the adapter that was initialized first, which is the counters' owner. The owner received correct values, while the other adapter only received zeros.
        * Fixed an issue that caused the rdma_cm traffic to fail on the 2nd port when more than 32 VFs were configured, when the RoCE Dual Port vHCA (a.k.a Multi-Port vHCA: MPV) feature was enabled.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.8-2.1
changelog:
  -     *Firmware for the following devices are updated to 2.42.5000:**  
        
      779799-B21 (HP Ethernet 10G 2-port 546FLR-SFP+ Adapter)  
      779793-B21 (HP Ethernet 10G 2-port 546SFP+ Adapter)
      
      **New features and changes in version 2.42.5000:**
      
        * Added support for the following features: 
          * TLV: CX3_GLOBAL_CONF to enable/disable timestamp on incoming packets through mlxconfig configuration.
          * User MAC configuration.
          * Automatically collecting mstdump before driver reset.
          * to detect DEAD_IRISC (plastic) from TPT (iron) and raise an assert.
        * Enhanced the debug ability for command timeout cases.
        * Added a new field to "set port" command which notifies the firmware what is the user_mtu size.
      
      **Firmware for the following devices are updated to 14.22.1414 :**
      
      817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)  
      817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
      **New features and changes in version 14.22.1414:**
      
        * Transition from 4MB to 7M Firmware Image Banks.
        * **Software Reset Flow:** Software detection of a fatal error, automatic creations of an mstdump file for future debug by the software, and resetting of the device.
        * **Steering Discard Packet Counters:** The following counters were added to count the discard packets (per vport) 
          * nic_receive_steering_discard
          * receive_discard_vport_down
          * transmit_discard_vport_down
        * **Virtual Functions (VF): **Increased the number of VFs that can work with full VMQoS (8 TC) per PFs as follow 
          * in dual port devices to 20 VFs
          * in single port devices to 58 VFs
        * Increased the Pause Frame Duration and the XOFF Resend Time to the maximum value defined by the specification.
        * **PCI Relax Ordering:** mlxconfig configuration can now enable or disable forced PCI relaxed ordering in mkey_context.
        * **vport Mirroring:** Packets are mirrored based on certain mirroring policy. The policy is set using the "set FTE command" that supports forward action in the ACL tables (ingress/egress).
        * **Resiliency: Special Error Event: **Added support for 10GBaseT modules connected to a QSFP cage.
        * Accelerated QP's creation time.
        * SR-IOV default routing mode is now LID based. The configuration change is available via mlxconfig tool.
        * Added PXE and UEFI to additional ConnectX-4 Lx adapter cards. ConnectX-4 Lx now holds PXE, x86-UEFI and Arm-UEFI.
      
      **Firmware for the following device is updated to 12.22.1414 :**
      
      868779-B21 (HPE Synergy 6410C 25/50Gb Ethernet Adapter)
      
      **New features and changes in version 12.22.1414:**
      
        * Transition from 4MB to 7M Firmware Image Banks.
        * **Software Reset Flow:** Software detection of a fatal error, automatic creations of an mstdump file for future debug by the software, and resetting of the device.
        * **Steering Discard Packet Counters:** The following counters were added to count the discard packets (per vport) 
          * nic_receive_steering_discard
          * receive_discard_vport_down
          * transmit_discard_vport_down
        * **Virtual Functions (VF): **Increased the number of VFs that can work with full VMQoS (8 TC) per PFs as follow 
          * in dual port devices to 20 VFs
          * in single port devices to 58 VFs
        * Increased the Pause Frame Duration and the XOFF Resend Time to the maximum value defined by the specification.
        * **PCI Relax Ordering:** mlxconfig configuration can now enable or disable forced PCI relaxed ordering in mkey_context.
        * **vport Mirroring:** Packets are mirrored based on certain mirroring policy. The policy is set using the "set FTE command" that supports forward action in the ACL tables (ingress/egress).
        * **Resiliency: Special Error Event: **Added support for 10GBaseT modules connected to a QSFP cage.
        * Accelerated QP's creation time.
        * SR-IOV default routing mode is now LID based. The configuration change is available via mlxconfig tool.
        * Added PXE and UEFI to additional ConnectX-4 Lx adapter cards. ConnectX-4 Lx now holds PXE, x86-UEFI and Arm-UEFI.
      
      
      
      **Firmware for the following device is updated to 16.22.1414 :**
      
      874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)
      
      **New features and changes in version 16.22.1414:**
      
        * Transition from 4MB to 7M Firmware Image Banks.
        * **Software Reset Flow:** Software detection of a fatal error, automatic creations of an mstdump file for future debug by the software, and resetting of the device.
        * **Steering Discard Packet Counters:** The following counters were added to count the discard packets (per vport) 
          * nic_receive_steering_discard
          * receive_discard_vport_down
          * transmit_discard_vport_down
        * Increased the Pause Frame Duration and the XOFF Resend Time to the maximum value defined by the specification.
        * **PCI Relax Ordering:** mlxconfig configuration can now enable or disable forced PCI relaxed ordering in mkey_context.
        * Added support for Push/Pop VLAN, new FLOW TABLE ENTRY actions. These new actions are used by the driver to implement Q-in-Q functionality.
        *  Packet Pacing in ConnectX-5 adapter cards.
        * **vport Mirroring:** Packets are mirrored based on certain mirroring policy. The policy is set using the "set FTE command" that supports forward action in the ACL tables (ingress/egress).
        * **Resiliency: Special Error Event: **Added support for 10GBaseT modules connected to a QSFP cage.
        * Accelerated QP's creation time.
        * SR-IOV default routing mode is now LID based. The configuration change is available via mlxconfig tool.
        * Added PXE and UEFI to additional ConnectX-4 Lx adapter cards. ConnectX-4 Lx now holds PXE, x86-UEFI and Arm-UEFI.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.8-2.1
changelog:
  -     *Fixes submitted in version 2.42.5000 :**
      
        * The PortRcvPkts counter was prevented from being cleared after resetting it..
        * System Time Out on the configuration cycle of the VFs when more than 10 Virtual Functions performed FLR and the completion Time Out value was configured to a range of less than 16 msec.
        * The server hung and resulted in NMI (Non-maskable interrupt) when run-ning "mlxfwtop -d mt4103_pci_cr0" while restarting the driver in parallel (from a differ-ent thread). In this case, the downstream bridge over the device reported completion timeout error. 
        * In flow_steering, BMC could not receive a ping over IPV6 after running bmc_reboot.
        * While closing the HCA (Host Channel Adapters), RX packet caused bad access to resources that did not exist, and consequently caused the QPCGW or the irisc to get stuck.
        * The master SMLID and the LID was either 0 or 0xFFFF when the port was neither active nor armed.
        * ibdump could not capture all MADs packets.
        * Link could not go up after reboot.
        * A rare issue caused the PCIe configuration cycle that arrived during the time of sw_reset to generate 2 completions. 
        * NC-SI (Network Controller Sideband Interface) did not work when adding the disable_stat-ic_steering_ini field in the ini file, due to memory allocation issue for this field in the scratchpad.
      
      **Fixes submitted in version 14.22.1414 :**
      
        * A temperature normalization function calculation issue. Now the cable gain that is not pure integer is taken into account was fixed.
        * An issue related to the parser of object 0x8 in ASN that caused different structure in response was fixed.
        * Added the option to avoid unintentionally powering off the backplane port cage upon reboot when in standby mode.
        * An issue that caused the driver to return a wrong logical OR of the 2 physical ports, when querying the vport state when the LAG was enabled wre fixed.
        * Increased the Full Wire Speed (FWS) threshold value to improve EDR link results.
        * An issue that resulted in "Destroy LAG" command failure if a VFs received an FLR while its affinity QPs were open.
        * When RoCE Dual Port mode is enabled, tcpdump is not functional on the 2nd port.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.9-2.1
changelog:
  -     *Fixes submitted in version 2.42.5044 :**
      
        * Fixed an issue that prevented the firmware from detecting a link_down event thus preventing the IB bond interface from going to a failover mode
      
      **Fixes submitted in version 12.23.8036 :**
      
        * Fixed a Phase-Locked Loop(PLL) tuning issue by improving the tx_clk_phase lock mechanism.
        * The Link Layer Discovery Protocol(LLDP): Removed management MAC 0 address once a new address is received
        * Set the Port ID to be the MAC of the port
      
      **Fixes submitted in version 14.23.8052:**
      
        * The HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter was not linking in AUX power mode.
      
      **Fixes submitted in version 16.23.8036 :**
      
        * Fixed an Active Health System(AHS) packet over PCIe interface issue


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.0
changelog:
  -     *Firmware for the following device has been updated to 12.21.1000:**
      
      843400-B21 (HPE Apollo A10 InfiniBand EDR (100Gb) 2-port Adapter)
      
      **New features and changes in version 12.21.1000:**
      
        * Added support for the following features: 
          * InfiniBand native (No SR-IOV) dual port device (Function per port is disabled). In this mode virtualization is not supported and ISSI = 0.
          * 10G/40G on 100GbE AOC/transceivers vs. non Mellanox devices.
        * PTP packets time stamping is enabled upon packet's arrival to the port.
        * Explicit Congestion Notification (ECN) is enabled by default for all priorities on Ethernet ports.
        * DC CNAK improves sent CNAK performance and avoids back pressure in ConnectX-4 adapter cards.
        * Receiver Signal Integrity Improvements: 
          * Raised the link only with phase greater than 15 ticks to improve signal integrity.
          * Extended measurement test between two similar RX configurations.
          * Moved the data path to use the second input buffer to improve signal integrity.
        * RDMA over Converged Ethernet (RoCE) Dual Port Mode enables the usage of a dual port Virtual HCA (vHCA) to share RDMA resources (e.g., MR, CQ, SRQ, PDs) across the two Ethernet (RoCE) NIC network ports and display the NIC as a dual port device. For this feature to function properly, the following requirements must be met: 
          * Either the LAG or the Dual Port mode is enabled by the driver.
          * Dual port device: both ports must be set as ETH.
          * In ConnectX-4/ConnectX-4 Lx adapter cards, the maximum allowed number of VFs per PF is 32.
          * Function per port is enabled.
        * QPDPM register is added to support dynamic mapping between DSCP and priority.
        * Trust level for QoS prioritization is added according to the DSCP or PCP.
        * Ingress buffer management is added for: 
          * ingress traffic mapping to a buffer according to priority.
          * buffers sizes and lossless parameters.
        * Enhanced steering rules update rate to up to 50K rules per second.
        * Enabled Windows single root input/output virtualization (SR-IOV) Enhanced eIPoIB (without Secure Connection) for Windows-over-Windows setups.
        * crdump operation takes a snapshot of the device's crspace dword-by-dword. It enables the driver to collect debug information upon firmware failure.
        * Secure Firmware Updates provides devices with the ability to verify digital signatures of new firmware binaries, in order to ensure that only officially approved versions are installed on the devices.
        * Changed the default Forward Error Connection (FEC) mode for cables with attenuation 16 and below from Reed Solomon (RS) to FC.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.0
changelog:
  -     *Fixes in version 12.21.1000:**
      
        * RDMA_CM driver was causing the Queue Pair (QP) Rate Limit to be activate unexpectedly and reduce the bandwidth significantly on this QP.
        * Low throughput when Eplicit Congestion Notification (ECN) was enabled in a many-to-one scenario.
        * A rare issue that caused the firmware to hang.
        * The maximum temperature in a setup was incorrectly reported as the current temperature regardless of the actual temperature.
        * Virtual Addressing Capability incorrect report in NC-SI (Sideband).
        * Enhanced RX sensitivity per Vcore.
        * Disabled the option to write to the protected modules to avoid receiving NACK upon module initialization.
        * Enabled cold_flicks reset when sending invalidate_all command to invalidate all the ECs.
        * SR-IOV min & max rate limiter can only support up to 64 Virtual Functions (VFs) per port.
        * Explicit Congestion Notification (ECN) did not function as expected when the number of QPs > ~500 per host.
        * When using Unreliable Datagram (UD) RDMA over Converged Ethernet (RoCE) multicast traffic over SR-IOV, packets were scattered to all the attached QPs in the e-sw (PF and its VFs) and not only on the vport that was specified in the e-se FDB.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.22
changelog:
  -     The firmware in this product addresses intermittent PCIe enumeration issues
      seen after warm/cold boot.
      
      The firmware in this product addresses a system crash seen when enabling NPAR
      with SRIOV enabled.
      
      The firmware in this product addresses an issue where a "NIC Initialization
      error" message is observed when PXE boot is attempted multiple times.
      
      The firmware in this product addresses an issue where the NCSI pass-through
      does not function when configured for DHCP IP.
      
      The firmware in this product addresses an issue where PXE boot fails in legacy
      boot mode.
      
      Ths firmware in this product addresses an issue where the system PXE boots
      when PXE boot is disabled on the port.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.1.29
changelog:
  -     This product now supports the following network adapters:
      
        * HPE Ethernet 10Gb 2-port 521T Adapter
        * HPE Ethernet 10Gb 2-port 522FLR-T Converged Network Adapter
        * HPE Ethernet 10/25Gb 2-port 621SFP28 Adapter
        * HPE Ethernet 10/25Gb 2-port 622FLR-SFP28 Converged Network Adapter
        * HPE Synergy 6810C 25/50Gb Ethernet Adapter


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.2.14
changelog:
  -     This product addresses an issue where the Wake-On-Lan setting on the second
      port isn't correctly enabled when the network adapter's configuration settings
      are restored to default in the 'System Utilities' (F9 on POST) under the
      'System Configuration' menu.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.3.12
changelog:
  -      This product addresses an issue where the inlet temperature is incorrectly reported.
        * This product addresses an issue where the Wake-On-LAN setting is not properly set on the second port after the defaults are restored.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.4.24
changelog:
  -      This product corrects an issue where booting to Preboot eXecution Environment (PXE) may not work after applying the OneView server profile when the System ROM is set to 'Legacy BIOS Mode'.
        * This product addresses an issue where the FCoE boot parameters cannot be configured in the adapter's configuration menu (under 'System Utilities'->'System Configuration' menu) when OneView profile with connections set to 'manually managed' is applied to the system.
        * This product corrects an issue where certain settings/changes (CHAP, boot mode etc) in the OneView server profile are not reflected in the adapters' configuration menu (under 'System Utilities'->'System Configuration' menu) after applying the OneView server profile.
        * This product corrects an issue where the virtual World Wide Port Name(WWPN)/World Wide Node Name(WWNN) are not programmed properly when applying the OneView server profile.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.4.65
changelog:
  -     This product now supports SUSE Linux Enterprise Server 15.
      
      This product now supports the following network adapters:
      
        * HPE Synergy 4820C 10/25Gb Converged Network Adapter
        * HPE StoreFabric CN1200R-T Converged Network Adapter
        * HPE StoreFabric CN1300R Converged Network Adapter


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.6.27
changelog:
  -     This product corrects an issue where the WWPN information is missing in an
      adapter's FCoE configuration menu (under 'System Utilities'->'System
      Configuration' menu).  
      This product corrects an issue where server hangs during POST when a network
      adapter is connected to the HPE Synergy 20Gb Interconnect Link Module.  
      This product corrects an issue where the initiator does not stay logged into
      the target in an FCoE connection.  
      This product corrects an issue where the link status continues to show as UP
      on the switch side even after a network adapter is disabled in the OS.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.19.22
changelog:
  -     This product addresses an issue where the system boots to an FCoE target when
      the FCoE ports are marked as "Not Bootable" in the OneView profile.
      
      This product addresses an issue booting to an iSCSI target fails when the
      target is configured with a sixteen character long mutual Challenge Handshake
      Authentication Protocol (CHAP) secret.
      
      This product addresses an issue where a network adapter's configuration
      settings are not reset to defaults when the adapter is moved to a different
      slot and the system is booted in 'Legacy BIOS Mode'.
      
      This product addresses an issue where the system's power-on self-test (POST)
      duration is extended when a single interconnect module (ICM) is installed in
      the enclosure and used to configure the logical interconnect group (LIG).
      
      This product addresses an issue where the configuration settings of the HPE
      Synergy 3820C 10/20Gb Converged Network Adapter revert to the default values
      after a system restart.
      
      This product addresses an issue where booting to an iSCSI target fails
      intermittently across multiple platform reboots.
      
      This product addresses an issue where OneView displays the downlink port state
      as "Linked" for a network adapter that is disabled in the OS.
      
      This product addresses an issue where a firmware update fails with a
      "segfault" error.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.20.4
changelog:
  -     This product addresses an issue where a network adapter cannot be re-added to
      a NIC bond after being removed from the bond.
      
      This product addresses an issue where adapters are not reporting the correct
      temperature in the Integrated Lights Out (iLO) webpage.
      
      This product addresses an issue where the value set for Maximum Transmission
      Unit (MTU) setting wasn't preserved and instead gets reverted back to default
      value on system reboot.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.20.5
changelog:
  -     This product addresses an issue where the users see the error message "Server
      profile settings conflict with the server hardware configuration" in OneView
      when applying the Server Profile to a server with VMware (ESXi 6.x).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.21.15
changelog:
  -      The default 'Boot Retry Count' has been increased from 'No Retry' to '6.'
        * Configuration settings are now localized.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.21.15
changelog:
  -      This product corrects an issue where the Maximum Transmission Unit (MTU) setting value reverts to the default value after a system reboot.
        * This product corrects an issue where an adapter's configuration menu doesn't correctly prompt for reboot after changes are made that require a reboot.
        * This product corrects a high latency issue seen during high ping activity.
        * This product corrects an issue where OneView displays the error message "Server profile settings conflict with the server hardware configuration" when applying the server profile to a server running VMware ESXi 6.x.
        * This product corrects an issue where the iSCSI settings configured in the OneView Profile are not correctly applied to the adapter.
        * This product corrects an issue where an error message is seen when entering the 'MBA Configuration Menu' under the adapter's settings (under the 'System Utilities->System Configuration' menu) and attempting to restore the defaults. 
        * This product corrects an issue where the iSCSI multipath does not work correctly in 'Legacy BIOS Mode'.
        * This product corrects an issue where the virtual World Wide Port Name(WWPN)/World Wide Node Name(WWNN) are not programmed properly when applying the OneView Server Profile.
        * This product addresses an issue where the user sees the error message "Unable to find a FibreChannel boot source for server" in OneView when applying the Server Profile with Fibre Channel network paths configured.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.22.15
changelog:
  -     This product corrects an issue where users may see an error message when they
      attempt to restore the adapter's configuration settings to defaults by
      pressing F7 under the 'System Utilities->System Configuration' menu.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.24.15
changelog:
  -     This product corrects an issue where a server does not boot via a network
      adapter in Legacy BIOS Mode.  
      This product corrects an issue where a server, across repeated reboots, is
      unable to boot into iSCSI LUN.  
      This product corrects an issue where a firmware update performed in UEFI fails
      when multiple adapters are connected to the system.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 8.4-2.1
changelog:
  -      Updated to support Service Pack for ProLiant version 2017.07.0
      
                **Note:** If version 8.4 was previously installed, then it is not necessary to upgrade to version 8.4 (B).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 8.4-3.1
changelog:
  -      Updated to support Service Pack for ProLiant version 2017.07.0
      
                **Note:** If version 8.4 was previously installed, then it is not necessary to upgrade to version 8.4 (C).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.20-2.1
changelog:
  -     Note: After running this component to update the NVMe Backplane PIC firmware,
      a server reboot is required for iLO to display the new NVMe Backplane PIC
      firmware version on iLO's Firmware Information page


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.20-2.1
changelog:
  -     Added support for the following Gen10 servers:
      
        * HPE ProLiant XL190r Gen10 Server
        * HPE ProLiant XL170r Gen10 Server
        * HPE ProLiant DL180 Gen10 Server
        * HPE ProLiant DL160 Gen10 Server
        * HPE ProLiant DL580 Gen10 Server
        * HPE ProLiant ML350 Gen10 Server
        * HPE ProLiant XL450 Gen10 Server
        * HPE ProLiant DL120 Gen10 Server


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.20-4.1
changelog:
  -     The following support was added in version 1.20(C). No new features were added
      in version 1.20(D).
      
        * Added support for the HPE ProLiant XL270d Gen10 Server


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.20-4.1
changelog:
  -     Firmware Package version 1.20(D) addressed the following issue:
      
        * When using OneView, attempts to upgrade firmware from version 1.18 to 1.20 failed.
      
      Note: If the target device was previously updated to firmware version 1.20, it
      is not necessary to apply firmware update 1.20(D).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      Integrated Lights-Out 5 (iLO 5) Firmware version 1.15 and System ROM version
      1.20 or later
      
      **Enhancements/New Features:**
      
      Added support for Dynamic Power Capping. For proper operation, please ensure
      that Integrated Lights-Out 5 (iLO 5) Firmware version 1.15 and System ROM
      version 1.20 or later are updated on the server.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4-2.1
changelog:
  -     *Important Notes:**
      
      Ver. 1.0.4 (B) contains support for new server products.  It is functionally
      equivalent to ver. 1.0.4.  It is not necessary to upgrade with Revision (B) if
      a previous component revision was used to upgrade the firmware to ver. 1.0.4.
      
      **Firmware Dependencies:**
      
      Integrated Lights-Out 5 (iLO 5) Firmware version 1.15 and System ROM version
      1.20 or later
      
      **Enhancements/New Features:**
      
      Added support for Dynamic Power Capping. For proper operation, please ensure
      that Integrated Lights-Out 5 (iLO 5) Firmware version 1.15 and System ROM
      version 1.20 or later are updated on the server.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.7-2.1
changelog:
  -     *Important Notes:**  
        
      Ver. 1.0.7(B) addresses a minor issue in the online flashing mechanism. The
      actual firmware contained within version 1.0.7(B) did not change as compared
      to version 1.0.7 and therefore it is not necessary to upgrade if version 1.0.7
      has already been installed.  
        
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      This is the initial version of the firmware.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.9
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addresses an issue in which the minimum power capping value was incorrectly
      being calculated on certain systems. This fix increases the accuracy of the
      minimum capping value set during POST.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.9-3.1
changelog:
  -     *Important Notes:**
      
      Ver. 1.0.9 (C) contains support for new server products and a change to the
      Firmware RPM install command name from "cpqsetup" to "hpsetup".  It is
      functionally equivalent to ver. 1.0.9.  It is not necessary to upgrade with
      Revision C if a previous component revision was used to upgrade the firmware
      to ver. 1.0.9.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addresses an issue in which the minimum power capping value was incorrectly
      being calculated on certain systems. This fix increases the accuracy of the
      minimum capping value set during POST.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.9-4.1
changelog:
  -     *Important Notes:**
      
      Ver. 1.0.9(D) contains updates to the component packaging and is functionally
      equivalent to ver. 1.0.9.  It is not necessary to upgrade with Revision D if a
      previous component Revision was used to upgrade the firmware to version 1.0.9.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addresses an issue in which the minimum power capping value was incorrectly
      being calculated on certain systems. This fix increases the accuracy of the
      minimum capping value set during POST.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.9-6.1
changelog:
  -     *Important Notes:**
      
      Ver. 1.0.9 (F) contains support for new server products.  It is functionally
      equivalent to ver. 1.0.9.  It is not necessary to upgrade with Revision F if a
      previous component revision was used to upgrade the firmware to ver. 1.0.9.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addresses an issue in which the minimum power capping value was incorrectly
      being calculated on certain systems. This fix increases the accuracy of the
      minimum capping value set during POST.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.9-7.1
changelog:
  -     *Important Notes:**
      
      Ver. 1.0.9 (G) contains a change to the Firmware RPM file name.  It is
      functionally equivalent to ver. 1.0.9.  It is not necessary to upgrade with
      Revision G if a previous component revision was used to upgrade the firmware
      to ver. 1.0.9.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addresses an issue in which the minimum power capping value was incorrectly
      being calculated on certain systems. This fix increases the accuracy of the
      minimum capping value set during POST.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.9-9.1
changelog:
  -     *Important Notes:**
      
      Ver. 1.0.9(I) contains updates to the component packaging and is functionally
      equivalent to ver. 1.0.9. It is not necessary to upgrade with Revision I if a
      previous component Revision was used to upgrade the firmware to version 1.0.9.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addresses an issue in which the minimum power capping value was incorrectly
      being calculated on certain systems. This fix increases the accuracy of the
      minimum capping value set during POST.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.9-10.1
changelog:
  -     *Important Notes:**
      
      Ver. 1.0.9(J) contains updates to the component packaging and is functionally
      equivalent to ver. 1.0.9. It is not necessary to upgrade with Revision J if a
      previous component Revision was used to upgrade the firmware to version 1.0.9.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addresses an issue in which the minimum power capping value was incorrectly
      being calculated on certain systems. This fix increases the accuracy of the
      minimum capping value set during POST.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.80
changelog:
  -      HP Smart Array Px3x controller with HP SmartCache enabled on boot volume could potentially encounter file corruption when booting the system if the Super-cap is not fully charged due to being replaced or being in a power down condition for several days (Example 7 days). File corruption is less likely to occur on non-boot volumes than on boot volumes. For additional information please refer to the customer advisory # [c04719000](http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=emr_na-c04719000)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 3.02
changelog:
  -      A physical drive configured as a spare drive might indicate predictive failure sooner than expected.
        * Controller might stop responding during run-time (POST Lockup 0x13).
        * After hot-plug replacement of a hard disk drive, incorrect hard disk drive firmware version and upgrade recommendation were displayed by HP Smart Storage Administrator.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 3.54
changelog:
  -      Detection of all direct-attached physical drives might fail if a single drive did not spin up.
        * Servers now power up faster due to improvements in the UEFI controller driver.
        * Reduced likelihood of POST Lockup 0x13 occurrence due to intermittent memory errors.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.04
changelog:
  -      System might hang at POST following a reboot.
        * System fans might go to 100% if connected drives were spun down.
        * SATA SSD's were incorrectly marked as worn out.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.08
changelog:
  -      Intermittent memory errors might cause the controller to stop responding. (POST Lockup 0x13)
      
        * System might stop responding if a parity error is found during surface scan of a RAID6 volume. (POST Lockup 0x13)
      
        * In rare cases, the controller might stop responding while running IO without displaying a lockup code.
      
        * Non-Maskable Interrupt (NMI) might occur on systems with a Windows OS and HPE Gen9 Smart Array or Smart HBA adapters and performing continuous reboot testing.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.10
changelog:
  -      If and unexpected power outage occurred, the system might stop operating during Power-On Self Test
      
        * Controller could stop responding when Smart Cache is performing a read-ahead after finishing a read-fill for a pending flush operation


