Add RHEL7 U5 support

]]> Added support for Red Hat Enterprise LINUX 7 Update 4

]]> The following issue has been resolved:

In a system configured with the HPE Dynamic Smart Array B140i Controller and higher than 128 CPU (cores), a system failure event would occur.

]]> Fixed the following items:

  • Improved handling of IPV6 addresses

  • Updated for RHEL 7.4 support

  • Supports SLES12 SP3

  • Improved handling of SATA drive temperatures

]]>
  • Added support for Red Hat Enterprise Linux 7.5.
    • ]]>
  • In rare cases, the driver might stop responding when using NCQ SATA drives.
    • ]]>
  • RPM might fail installation due to missing dependency.
    • ]]>         Fixed the following items:

    • Files in directories under /var/spool/compaq/hpasm/registry/ have SGID bit set
    • Total MEM shows“0MB” w/ 32pcs 128G DIMM in SMH-System Board in Linux
    • HPSUM discovery works for G7 platforms
    ]]>
  • Support for HPE FlexFabric 10Gb 2-port 556FLR-T Adapter.
  • Support for HPE StoreFabric CN1200E 10G BASE-T Dual Port Converged Network Adapter.
  • Support for memory dram speed 2400 Mbits.
  • Support for DDR4-2400 1.2V memory.
  • Support for Apollo 4520 Storage Expander.
  • Support 6 SFF rear cage for Apollo 4200.
  • Support for StoreFabric CN1100R-T Converged Network Adapter.
  • Hewlett Packard Enterprise rebrand.

    • See the HP Service Pack for ProLiant Release Notes for more information.

    See the HP Service Pack for ProLiant Server Support Guide for information on supported servers.

    ]]>
  • Contains fixes to support HPE ProLiant Gen9 servers.
  • DL60 blank Remote Management category.
  • Untranslated English to Japanese strings.
  • Blank Remote Control section in Survey for DL20 Gen9.
  • Capability to report same backplanes but different box numbers. 
    • ]]>         NA

    ]]>         See the iSUT Release Notes for information about the issues resolved in this release.

    ]]>         See the iSUT Release Notes for information about the issues resolved in this release.

    ]]>         Added support for RHEL 7.5

    ]]>         Added support for Red Hat Enterprise LINUX 7 Update 4.

    ]]>         Fixed the following items:

    • Improved handling of IPV6 addresses

    • Updated for RHEL 7.4 support

    • Improved handling of SATA drive temperatures

    ]]>         Updated the following components:

    • PHP to version 5.6.30
    • Zlib to version 1.2.11
    • PCRE to version 8.41
    • Libxslt to version 1.1.32
    ]]>

  • Updated the following components:

    • PHP to version 5.6.27

    • OpenSSL to version 1.0.2k

    • Apache to version 2.4.25

  • Improved Security features [Please find more details in the Security Bulletin (ID: HPESBMU03753)]

  • Enabled support for RHEL 6.9, RHEL 7.3 and SLES 12.2 OS

    • ]]>         Updated to version: 11.4.1205.0

    ]]>         Updated to version: 11.2.1263.2

    ]]>         Updated the kit to version 6.0.0.0-4

    ]]>         Updated the kit to version 6.0.0.0-4

    ]]>
  • Added support for Freeze/Anti-freeze of the Sanitize command.
    • ]]>
  • Initial firmware release for HPE P/E-Class SR Gen10 controllers.
    • ]]>         Add RHEL7 U5 support

    ]]>         Fixes an issue where the system could panic after a kernel buffer message "Inquiry failed"

    ]]>         Fixed the following items:

    • NIC tab is now visible on SMH Home page after setting data source as snmp

    • HPSUM discovery works for G7 platforms

    ]]>
  • Added support for Freeze/Anti-freeze of the Sanitize command.
    • ]]>
  • Initial firmware release for HPE P/E-Class SR Gen10 controllers.
    • ]]>
  • Fixed hp-health to work with linux kernel versions 4.X
    • ]]>         Fixed the following items:

    • File permissions for hp-health services
    • HPSUM discovery works with G7 platforms
    ]]>         Add RHEL7 U5 support

    ]]>         Fixes an issue where the system could panic after a kernel buffer message "Inquiry failed"

    ]]>         Added support for RHEL 7.5

    ]]>         Added support for Red Hat Enterprise LINUX 7 Update 4.

    ]]>
  • Added support for Freeze/Anti-freeze of the Sanitize command.
    • ]]>
  • Initial firmware release for HPE P/E-Class SR Gen10 controllers.
    • ]]>         Updated to version 3.3-3(b)

    ]]>         Added support for the following devices:

    • HPE StoreFabric 84Q 4P 8Gb Fibre Channel HBA
    • HPE Synergy 3830C 16G Fibre Channel Host Bus Adapter
    ]]>         Updated to version 1.0.0.0-4 (b)

    ]]>         Added support for the following device:

    • HPE Synergy 3530C 16Gb Fibre Channel Host Bus Adapter
    ]]>         Introduced support for iLO 5 v1.20.

    ]]>         Fixed issue where IML and IEL logs were not cleared after doing iLO factory default.

    ]]>         Introduced support for iLO 5 v1.15.

    ]]>         Add RHEL7 U5 support

    ]]>         Added support for Red Hat Enterprise LINUX 7 Update 4

    ]]>         The following issue has been resolved:

    In a system configured with the HPE Dynamic Smart Array B140i Controller and higher than 128 CPU (cores), a system failure event would occur.

    ]]>         Updated code for the following:

    • Emulex CNA Driver display due to split
    • Optrom version display
    ]]>         General update.

    ]]>
  • Added support for Red Hat Enterprise Linux 7.5.
    • ]]>
  • In rare cases, the driver might stop responding when using NCQ SATA drives.
    • ]]>
  • RPM might fail installation due to missing dependency.
    • ]]>         Updated to version 11.4.207.0

    ]]>         Updated to version 11.2.307.3

    Added support for Rhel7u4

    ]]>