XYPLEX CHARACTER MIB 18 Oct 91
Definitions of Managed Objects
for Xyplex Character Stream Devices
18 October 1991
Xyplex Document Number 420-0539-A
Xyplex, Inc.
330 Codman Hill Road
Boxborough, MA 01719
(508) 264-9900
support@xyplex.com
1. Status of this Memo
This document is submitted to the Internet MIB repository
and to Xyplex users as a Xyplex private extension to the
SNMP MIB. Distribution of this memo is unlimited. Please
express comments to Xyplex.
2. Abstract
This memo defines a private portion of the Management
Information Base (MIB), within the Xyplex branch, for use
with SNMP over various transport services, such as UDP or
[Page 1]
XYPLEX CHARACTER MIB 18 Oct 91
Ethernet. In particular, it defines objects for managing
character stream devices in Xyplex systems.
This memo does not specify a standard for the Internet
community. It describes a standard for Xyplex products.
[Page 2]
XYPLEX CHARACTER MIB 18 Oct 91
3. Historical Perspective
As reported in RFC 1052, IAB Recommendations for the
Development of Internet Network Management Standards [1], a
two-prong strategy for network management of TCP/IP-based
internets was undertaken. In the short-term, the Simple
Network Management Protocol (SNMP), defined in RFC 1067, was
to be used to manage nodes in the Internet community. In
the long-term, the use of the OSI network management
framework was to be examined. Two documents were produced
to define the management information: RFC 1065, which
defined the Structure of Management Information (SMI), and
RFC 1066, which defined the Management Information Base
(MIB). Both of these documents were designed so as to be
compatible with both the SNMP and the OSI network management
framework.
This strategy was quite successful in the short-term:
Internet-based network management technology was fielded, by
both the research and commercial communities, within a few
months. As a result of this, portions of the Internet
community became network manageable in a timely fashion.
As reported in RFC 1109, Report of the Second Ad Hoc Network
Management Review Group [2], the requirements of the SNMP
and the OSI network management frameworks were more
different than anticipated. As such, the requirement for
compatibility between the SMI/MIB and both frameworks was
suspended. This action permitted the operational network
management framework, based on the SNMP, to respond to new
operational needs in the Internet community by producing
MIB-II.
In May of 1990, the core documents were elevated to
"Standard Protocols" with "Recommended" status. As such,
the Internet- standard network management framework consists
of: Structure and Identification of Management Information
for TCP/IP-based internets, RFC 1155 [4], which describes
how managed objects contained in the MIB are defined;
Management Information Base for Network Management of
TCP/IP-based internets, which describes the managed objects
contained in the MIB, RFC 1156 [5]; and, the Simple Network
Management Protocol, RFC 1157 [6], which defines the
protocol used to manage these objects.
Consistent with the IAB directive to produce simple,
[Page 3]
XYPLEX CHARACTER MIB 18 Oct 91
workable systems in the short-term, the list of managed
objects defined in the Internet-standard MIB was derived by
taking only those elements which are considered essential.
However, the SMI defined three extensibility mechanisms:
one, the addition of new standard objects through the
definitions of new versions of the MIB; two, the addition of
widely-available but non- standard objects through the
experimental subtree; and three, the addition of private
objects through the enterprises subtree. Such additional
objects can not only be used for vendor-specific elements,
but also for experimentation as required to further the
knowledge of which other objects are essential.
This memo defines extensions to the MIB using the third
method. It contains definitions of managed objects in
various Xyplex products, using ASN.1 conventions specified
in [10].
[Page 4]
XYPLEX CHARACTER MIB 18 Oct 91
4. Objects
Managed objects are accessed via a virtual information
store, termed the Management Information Base or MIB.
Objects in the MIB are defined using the subset of Abstract
Syntax Notation One (ASN.1) [7] defined in the SMI. In
particular, each object has a name, a syntax, and an
encoding. The name is an object identifier, an
administratively assigned name, which specifies an object
type. The object type together with an object instance
serves to uniquely identify a specific instantiation of the
object. For human convenience, we often use a textual
string, termed the OBJECT DESCRIPTOR, to also refer to the
object type.
The syntax of an object type defines the abstract data
structure corresponding to that object type. The ASN.1
language is used for this purpose. However, the SMI [4]
purposely restricts the ASN.1 constructs which may be used.
These restrictions are explicitly made for simplicity.
The encoding of an object type is simply how that object
type is represented using the object type's syntax.
Implicitly tied to the notion of an object type's syntax and
encoding is how the object type is represented when being
transmitted on the network.
The SMI specifies the use of the basic encoding rules of
ASN.1 [8], subject to the additional requirements imposed by
the SNMP.
4.1. Format of Definitions
Section 6 contains the specification of all object types
contained in this MIB module. The object types are defined
using the conventions defined in the SMI, as amended by the
extensions specified in [9].
[Page 5]
XYPLEX CHARACTER MIB 18 Oct 91
5. Overview
The Xyplex Character MIB contains information for managing
character stream devices in Xyplex systems where that
information is not part of any Internet standard,
specifically, the Internet Experimental Character MIB and
its companions the RS232-like MIB and Parallel Printer-like
MIB.
The Xyplex Character MIB is mandatory for all Xyplex systems
that support character stream sessions through either
physical or logical ports. This includes, for example,
terminal servers, printer servers, bridges with a single
terminal port, and devices with no physical port but
supporting a remote console character stream.
The Xyplex MiniMIB [11] contained a Character group that is
now deprecated in favor of the combination of the Internet
Experimental Character MIB and the Xyplex Character MIB as
defined in this document. Implementation of the deprecated
Character group is an individual product issue, based on the
need for compatibility with earlier MiniMIB
implementations.
The Xyplex Character MIB comprises several groups that
correspond in spirit to the standard Internet MIB. As in
the standard MIB, these groups are not implemented if the
system does not have the corresponding functions. For
example, a system that does not implement network login does
not implement the Xyplex Character Network Login group.
As a convenience to the reader, the Character MIB groups
are:
basic
queue
menu
netLogin
dial
sessionLog
The basic group contains the following base objects:
basicBroadcast
basicErrorReport
basicLock
[Page 6]
XYPLEX CHARACTER MIB 18 Oct 91
basicInactivityTimer
basicPasswordRetryLimit
basicPrivilegedPassword
basicLoginPassword
basicLoginPrompt
basicWelcome
basicActivePorts
basicActivePortsHigh
basicActiveUsers
basicActiveUsersHigh
basicSessions
basicSessionsHigh
basicSessionsLimit
basicConsoleLogoutDisconnect
The basic group contains a table of serial and parallel
ports:
basicPortIndex
basicPortDefaultDestAction
basicPortDefaultDestProtocol
basicPortDefaultDestName
basicPortDefaultDestLATNodeName
basicPortDefaultDestLATPortName
basicPortAutoConnect
basicPortAutoLogin
basicPortBroadcast
basicPortConnectResume
basicPortDialup
basicPortIdleTimeout
basicPortInactivityLogout
basicPortLossNotification
basicPortMessageCodes
basicPortMultisessions
basicPortDefaultUserName
basicPortVerification
basicPortDefaultProtocol
basicPortLogins
basicPortRemoteSessions
basicPortIdleTimeouts
basicPortStatus
[Page 7]
XYPLEX CHARACTER MIB 18 Oct 91
basicPortLastInCharacter
basicPortLastOutCharacter
basicPortActiveUserName
basicPortDefaultSessionMode
basicPortZero
basicPortZeroTime
The basic group contains a table of serial ports:
basicSerialPortIndex
basicSerialPortBreak
basicSerialPortInterrupts
basicSerialPortNoLoss
basicSerialPortPause
basicSerialPortPrompt
basicSerialPortTerminalType
basicSerialPortTypeaheadLimit
basicSerialPortBackwardSwitch
basicSerialPortForwardSwitch
basicSerialPortLocalSwitch
basicSerialPortModemControl
basicSerialPortSignalCheck
basicSerialPortDSRLogout
basicSerialPortDSRObserve
basicSerialPortDCDTimeout
basicSerialPortDTRAssert
basicSerialPortLimitedCommands
basicSerialPortLimitedView
basicSerialPortPassword
basicSerialPortLineEditor
basicSerialPortLineEditorBackspace
basicSerialPortLineEditorBeginning
basicSerialPortLineEditorCancel
basicSerialPortLineEditorDeleteBeginning
basicSerialPortLineEditorDeleteLine
basicSerialPortLineEditorEnd
basicSerialPortLineEditorForward
basicSerialPortLineEditorInsertToggle
basicSerialPortLineEditorNextLine
[Page 8]
XYPLEX CHARACTER MIB 18 Oct 91
basicSerialPortLineEditorPreviousLine
basicSerialPortLineEditorQuotingCharacter
basicSerialPortLineEditorRedisplay
The queue group contains the following base objects:
queueLimit
queueHigh
queueNumber
The queue group contains a table of queue entries:
queueJob
queueStatus
queueSourceName
queueServiceName
queueServicePortIndex
queueServicePortName
The queue group contains a table of port entries:
queuePortIndex
queuePortQueuing
The menu group contains the following base objects:
menuNumber
menuContinuePrompt
menuSelectionPrompt
The menu group contains a table of menu entries:
menuIndex
menuStatus
menuText
menuCommand
The menu group contains a table of port entries:
menuPortIndex
menuPortMenuStatus
The Network Login group contains:
netLoginServerNumber
[Page 9]
XYPLEX CHARACTER MIB 18 Oct 91
The Network Login group contains a table of script servers:
netLoginServerName
netLoginServerStatus
netLoginServerPath
The Network Login group also contains a table of ports:
netLoginPortIndex
netLoginPortScriptUse
netLoginPortScriptEcho
netLoginPortLoaderAddressType
netLoginPortLoaderAddress
netLoginPortLoaderPath
The Dial group also contains a table of ports:
dialPortIndex
dialPortDialback
dialPortDialbackTimeout
The Session Log group contains:
sessionLogLimit
The Session Log group also contains a table of log entries:
sessionLogIndex
sessionLogStatus
sessionLogPort
sessionLogEvent
sessionLogEventDetail
sessionLogUserName
sessionLogRemoteName
sessionLogConnectTime
sessionLogDisconnectTime
sessionLogInCharacters
sessionLogOutCharacters
[Page 10]
XYPLEX CHARACTER MIB 18 Oct 91
6. Definitions
XYPLEX-CHARACTER-MIB DEFINITIONS ::= BEGIN
IMPORTS
enterprises, Counter, Gauge
FROM RFC1155-SMI
DisplayString
FROM RFC1158-MIB
OBJECT-TYPE
FROM RFC1212-CONCISE-MIB
DateTime, AddressType
FROM XYPLEX-SYSTEM-MIB;
xyplex OBJECT IDENTIFIER ::= { enterprises 33 }
characterDep OBJECT IDENTIFIER ::= { xyplex 2 }
character OBJECT IDENTIFIER ::= { xyplex 13 }
-- Xyplex Character subgroups
basic OBJECT IDENTIFIER ::= { character 1 }
queue OBJECT IDENTIFIER ::= { character 2 }
menu OBJECT IDENTIFIER ::= { character 3 }
netLogin OBJECT IDENTIFIER ::= { character 4 }
dial OBJECT IDENTIFIER ::= { character 5 }
sessionLog OBJECT IDENTIFIER ::= { character 6 }
-- This MIB module uses the extended OBJECT-TYPE macro as
-- defined in [9]
-- This is a MIB module for all Xyplex systems that
-- implement physical or logical character stream devices
[Page 11]
XYPLEX CHARACTER MIB 18 Oct 91
-- the Character Basic group
-- Implementation of this group is mandatory for all Xyplex
-- systems that implement physical or logical character
-- stream devices
basicBroadcast OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for user ability to broadcast messages to
other local ports. Corresponds directly to SERVER
BROADCAST and the presence of the label 'Broadcast'
following the label 'Enabled Characteristics:' in
the SERVER CHARACTERISTICS display."
::= { basic 1 }
basicErrorReport OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for server display of an error when the
user gives an unsupported command. Corresponds
directly to SERVER REPORT ERRORS and the presence of
the label 'Report Errors' following the label
'Enabled Characteristics:' in the SERVER
CHARACTERISTICS display."
::= { basic 2 }
basicLock OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for user ability to use a password to
protect a logged in terminal from other users.
Corresponds directly to SERVER LOCK and the presence
of the label 'Lock' following the label 'Enabled
Characteristics:' in the SERVER CHARACTERISTICS
display."
::= { basic 3 }
basicInactivityTimer OBJECT-TYPE
SYNTAX INTEGER (1..120)
[Page 12]
XYPLEX CHARACTER MIB 18 Oct 91
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Number of minutes a terminal may remain logged in
with no sessions, no input or output, and no modem
transitions. Corresponds directly to SERVER
INACTIVITY TIMER and the value labeled 'Inactivity
Timer:' in the SERVER CHARACTERISTICS display."
::= { basic 4 }
basicPasswordRetryLimit OBJECT-TYPE
SYNTAX INTEGER (0..250)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Number of times the server allows a user to retry
an incorrect password. Corresponds directly to
SERVER PASSWORD LIMIT and the value labeled
'Password Limit:' in the SERVER CHARACTERISTICS
display."
::= { basic 5 }
basicPrivilegedPassword OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..16))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The password a user must enter to become
privileged.
For security reasons, reading this object always
returns a zero-length value. Corresponds directly
to SERVER PRIVILEGED PASSWORD."
::= { basic 6 }
basicLoginPassword OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..16))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The password a user must enter to be given the
opportunity to log in. For security reasons,
reading this object always returns a zero-length
value. Corresponds directly to SERVER LOGIN
PASSWORD."
::= { basic 7 }
[Page 13]
XYPLEX CHARACTER MIB 18 Oct 91
basicLoginPrompt OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..8))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The text string the server displays to prompt a
user for the login password. Corresponds directly
to SERVER LOGIN PROMPT."
::= { basic 8 }
basicWelcome OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..80))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The text string the server displays before
attempting to log in a user. Corresponds directly
to SERVER WELCOME and the value labeled 'Welcome:'
in the SERVER CHARACTERISTICS display."
::= { basic 9 }
basicActivePorts OBJECT-TYPE
SYNTAX Gauge
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of ports with connected sessions or
logged in users. Corresponds directly to the value
labeled 'Active Ports:' and 'Cur' in the SERVER
STATUS display."
::= { basic 10 }
basicActivePortsHigh OBJECT-TYPE
SYNTAX Gauge
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The highest value of basicActivePorts since system
initialization. Corresponds directly to the value
labeled 'Active Ports:' and 'High' in the SERVER
STATUS display."
::= { basic 11 }
basicActiveUsers OBJECT-TYPE
SYNTAX Gauge
ACCESS read-only
[Page 14]
XYPLEX CHARACTER MIB 18 Oct 91
STATUS mandatory
DESCRIPTION
"The number of logged in users. Corresponds
directly to the value labeled 'Active Users:' and
'Cur' in the SERVER STATUS display."
::= { basic 12 }
basicActiveUsersHigh OBJECT-TYPE
SYNTAX Gauge
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The highest value of basicActiveUsers since system
initialization. Corresponds directly to the value
labeled 'Active Users:' and 'High' in the SERVER
STATUS display."
::= { basic 13 }
basicSessions OBJECT-TYPE
SYNTAX Gauge
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The total number of connected sessions.
Corresponds directly to the value labeled 'Connected
Sessions:' and 'Cur' in the SERVER STATUS display."
::= { basic 14 }
basicSessionsHigh OBJECT-TYPE
SYNTAX Gauge
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The highest value of basicSessions since system
initialization. Corresponds directly to the value
labeled 'Connected Sessions:' and 'High' in the
SERVER STATUS display."
::= { basic 15 }
basicSessionsLimit OBJECT-TYPE
SYNTAX INTEGER (-1..64)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The maximum total number of sessions that can
simultaneously be connected to the system. A value
[Page 15]
XYPLEX CHARACTER MIB 18 Oct 91
of -1 indicates no limit up to available dynamic
system memory. Corresponds directly to SERVER
SESSION LIMIT and the value labeled 'Connected
Sessions:' and 'Max' in the SERVER STATUS display."
::= { basic 16 }
-- Additional Basic group parameters follow the port tables
[Page 16]
XYPLEX CHARACTER MIB 18 Oct 91
-- the Basic Port table
basicPortTable OBJECT-TYPE
SYNTAX SEQUENCE OF BasicPortEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of basic character port entries."
::= { basic 17 }
basicPortEntry OBJECT-TYPE
SYNTAX BasicPortEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Basic parameter values for a port."
INDEX { basicPortIndex }
::= { basicPortTable 1 }
BasicPortEntry ::=
SEQUENCE {
basicPortIndex
INTEGER,
basicPortDefaultDestAction
INTEGER,
basicPortDefaultDestProtocol
INTEGER,
basicPortDefaultDestName
DisplayString,
basicPortDefaultDestLATNodeName
DisplayString,
basicPortDefaultDestLATPortName
DisplayString,
basicPortAutoConnect
INTEGER,
basicPortAutoLogin
INTEGER,
basicPortBroadcast
INTEGER,
basicPortConnectResume
INTEGER,
basicPortDialup
INTEGER,
basicPortIdleTimeout
INTEGER,
basicPortInactivityLogout
[Page 17]
XYPLEX CHARACTER MIB 18 Oct 91
INTEGER,
basicPortLossNotification
INTEGER,
basicPortMessageCodes
INTEGER,
basicPortMultisessions
INTEGER,
basicPortDefaultUserName
DisplayString,
basicPortVerification
INTEGER,
basicPortDefaultProtocol
INTEGER,
basicPortLogins
Counter,
basicPortRemoteSessions
Counter,
basicPortIdleTimeouts
Counter,
basicPortStatus
INTEGER,
basicPortLastInCharacter
INTEGER,
basicPortLastOutCharacter
INTEGER,
basicPortActiveUserName
DisplayString,
basicPortDefaultSessionMode
INTEGER,
basicPortZero
INTEGER,
basicPortZeroTime
TimeTicks
}
basicPortIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An index value that uniquely identifies a port.
The port identified by a particular value of this
index is the same port as identified by
charPortIndex in the Character MIB [12]."
::= { basicPortEntry 1 }
[Page 18]
XYPLEX CHARACTER MIB 18 Oct 91
basicPortDefaultDestAction OBJECT-TYPE
SYNTAX INTEGER { dedicated(1), preferred(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The action to take relative to
basicPortDefaultDestName. Corresponds directly to
PORT DEDICATED/PREFERRED SERVICE and the label
'Dedicated/Preferred Service:' in the PORT
CHARACTERISTICS display."
::= { basicPortEntry 2 }
basicPortDefaultDestProtocol OBJECT-TYPE
SYNTAX INTEGER { lat(1), telnet(2), any(3) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The session protocol to use with
basicPortDefaultDestName. Corresponds directly to
LAT/TELNET PORT DEDICATED/PREFERRED SERVICE."
::= { basicPortEntry 3 }
basicPortDefaultDestName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..50))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The default name to use in forming a connection
when no other name is specified. Corresponds
directly to PORT DEDICATED/PREFERRED SERVICE and the
value labeled 'Dedicated/Preferred Service:' in the
PORT CHARACTERISTICS display. If the value of
basicPortDefaultDestProtocol is 'telnet', an
Internet port number may be included on the end of
the name, delimited with a colon (':'). If the
value of basicPortDefaultDestProtocol is not
'telnet', then the maximum length is 16."
::= { basicPortEntry 4 }
basicPortDefaultDestLATNodeName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..16))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"A LAT node name to use with
basicPortDefaultDestName. Corresponds directly to
[Page 19]
XYPLEX CHARACTER MIB 18 Oct 91
PORT DEDICATED/PREFERRED SERVICE NODE and the value
labeled 'Node:' following the label
'Dedicated/Preferred Service:' in the PORT
CHARACTERISTICS display. This object can have a
non- zero-length value only if the value of
basicPortDefaultDestProtocol is 'lat'."
::= { basicPortEntry 5 }
basicPortDefaultDestLATPortName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..16))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"A LAT port name to use with
basicPortDefaultDestName. Corresponds directly to
PORT DEDICATED/PREFERRED SERVICE NODE and the value
labeled 'Node:' following the label
'Dedicated/Preferred Service:' in the PORT
CHARACTERISTICS display. this object can hav a
non-zero-length value only if the value if
basicPortDefaultDestProtocol is 'lat'"
::= { basicPortEntry 6 }
basicPortAutoConnect OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for automatic session connection.
Corresponds directly to PORT AUTOCONNECT and the
presence of the label 'Autoconnect' following the
label 'Enabled Characteristics:' in the PORT
CHARACTERISTICS display."
::= { basicPortEntry 7 }
basicPortAutoLogin OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for automatic port login. Corresponds
directly to PORT AUTODEDICATED and the presence of
the label 'Autodedicated' following the label
'Enabled Characteristics:' in the PORT
CHARACTERISTICS display."
::= { basicPortEntry 8 }
[Page 20]
XYPLEX CHARACTER MIB 18 Oct 91
basicPortBroadcast OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for display of messages sent by users on
other ports. Corresponds directly to PORT BROADCAST
and the presence of the label 'Broadcast' following
the label 'Enabled Characteristics:' in the PORT
CHARACTERISTICS display."
::= { basicPortEntry 9 }
basicPortConnectResume OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for behavior of a connection attempt to a
destination where the port already has a connection.
'disabled' causes a new connection. 'enabled'
causes the existing connection to become the active
connection. Corresponds directly to PORT
CONNECTRESUME and the presence of the label
'Connectresume' following the label 'Enabled
Characteristics:' in the PORT CHARACTERISTICS
display."
::= { basicPortEntry 10 }
basicPortDialup OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Defines whether the port should be considered as
connected to a dialup line. 'enabled' means that it
is. Corresponds directly to PORT DIALUP and the
presence of the label 'Dial Up' following the label
'Enabled Characteristics:' in the PORT
CHARACTERISTICS display."
::= { basicPortEntry 11 }
basicPortIdleTimeout OBJECT-TYPE
SYNTAX INTEGER (-1..255)
ACCESS read-write
STATUS mandatory
[Page 21]
XYPLEX CHARACTER MIB 18 Oct 91
DESCRIPTION
"The number of minutes the system will allow a
session to have no activity before automatically
disconnecting it. A value of -1 indicates no
timeout. Zero is not a valid value. Corresponds
directly to PORT IDLE TIMEOUT and the value labeled
'Idle Timeout:' in the PORT ALTERNATE
CHARACTERISTICS display."
::= { basicPortEntry 12 }
basicPortInactivityLogout OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for the system automatically logging the
port out when it has no sessions, no local activity,
and no modem signal changes for the time period
specified by basicInactivityTimer. Corresponds
directly to PORT INACTIVITY LOGOUT and the presence
of the label 'Inactivity Logout' following the label
'Enabled Characteristics:' in the PORT
CHARACTERISTICS display."
::= { basicPortEntry 13 }
basicPortLossNotification OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for the system sending a Bell character to
the port when it looses an input character due to an
overrun or data error. Corresponds directly to PORT
LOSS NOTIFICATION and the presence of the label
'Loss Notification' following the label 'Enabled
Characteristics:' in the PORT CHARACTERISTICS
display."
::= { basicPortEntry 14 }
basicPortMessageCodes OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for including error numbers in error
messages displayed on the port. Corresponds
[Page 22]
XYPLEX CHARACTER MIB 18 Oct 91
directly to PORT MESSAGE CODES and the presence of
the label 'Message Codes' following the label
'Enabled Characteristics:' in the PORT
CHARACTERISTICS display."
::= { basicPortEntry 15 }
basicPortMultisessions OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for running the multisession line protocol
between the port and the locally-connected terminal.
Corresponds directly to PORT MULTISESSIONS and the
presence of the label 'Multisessions' following the
label 'Enabled Characteristics:' in the PORT
CHARACTERISTICS display."
::= { basicPortEntry 16 }
basicPortDefaultUserName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..16))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Default user name to use for automatically logging
in the port. Corresponds directly to PORT USERNAME
and the value labeled 'Port n:' in the PORT
CHARACTERISTICS display."
::= { basicPortEntry 17 }
basicPortVerification OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for display of informational messages on
the port when the user connects, disconnects, or
switches a session. Corresponds directly to PORT
VERIFICATION and the presence of the label
'Verification' following the label 'Enabled
Characteristics:' in the PORT CHARACTERISTICS
display."
::= { basicPortEntry 18 }
basicPortDefaultProtocol OBJECT-TYPE
SYNTAX INTEGER { lat(1), telnet(2), any(3) }
[Page 23]
XYPLEX CHARACTER MIB 18 Oct 91
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The session protocol to use when not otherwise
specified. Corresponds directly to PORT RESOLVE
SERVICE and the value labeled 'Resolve Service:' in
the PORT ALTERNATE CHARACTERISTICS display."
::= { basicPortEntry 19 }
basicPortLogins OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of logins on the port since system
initialization. Corresponds directly to the value
labeled 'Local Accesses:' in the PORT COUNTERS
display."
::= { basicPortEntry 20 }
basicPortRemoteSessions OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of remotely originating sessions to the
port since system initialization. Corresponds
directly to the value labeled 'Remote Accesses:' in
the PORT COUNTERS display."
::= { basicPortEntry 21 }
basicPortIdleTimeouts OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of session disconnects due to expiration
of basicPortIdleTimeout. Corresponds directly to
the value labeled 'Idle Timeouts:' in the PORT
COUNTERS display."
::= { basicPortEntry 22 }
basicPortStatus OBJECT-TYPE
SYNTAX INTEGER { idle(1), local(2), waitInput(3),
executingCommand(4), connecting(5),
checkConnect(6), waitOutput(7),
[Page 24]
XYPLEX CHARACTER MIB 18 Oct 91
connected(8), disconnecting(9),
disconnect(10), suspended(11),
locked(12), permanent(13),
loginWait(14), retryConnect(15),
connectWait(16), logout(17),
login(18), waitSession(19),
reset(20), testServiceWait(21),
testServiceOut(22),
connectPassword(23),
waitLogout(24), waitQueue(25),
cancelQueue(26), autobaud(27),
available(28), checkModem(29),
slip(30), signalWait(31),
scriptSearch(32), scriptLoad(33),
scriptRun(34), dialback1(35),
dialback2(36), dialback3(37),
xremote(38) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The current operational status of the port.
Corresponds directly to the value labeled 'Status:'
in the PORT STATUS display."
::= { basicPortEntry 23 }
basicPortLastInCharacter OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The character that most recently came into the
port. Corresponds directly to the value labeled
'Last Char Input:' in the PORT STATUS display."
::= { basicPortEntry 24 }
basicPortLastOutCharacter OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The character that most recently went out of the
port. Corresponds directly to the value labeled
'Last Char Output:' in the PORT STATUS display."
::= { basicPortEntry 25 }
basicPortActiveUserName OBJECT-TYPE
[Page 25]
XYPLEX CHARACTER MIB 18 Oct 91
SYNTAX DisplayString (SIZE (0..16))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The user name currently logged into the port.
Corresponds directly to the value by the port number
and labeled 'Username' in the USERS display."
::= { basicPortEntry 26 }
basicPortDefaultSessionMode OBJECT-TYPE
SYNTAX INTEGER { interactive(1), binary(2),
binaryWithFlow(3), transparent(4) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Data recognition mode when starting a session,
with
the following meanings:
interactive locally recognize all controls
binary recognize only session protocol
(corresponds to PASSALL)
binaryWithFlow recognize only XON and XOFF
(corresponds to PASTHRU
transparent recognize no data
Corresponds directly to PORT DEFAULT SESSION MODE
and
the value labeled 'Default Session Mode:' in the
PORT
ALTERNATE CHARACTERISTICS display."
::= { basicPortEntry 27 }
basicPortZero OBJECT-TYPE
SYNTAX INTEGER { ready(1), execute(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control to zero counters for the port. In response
to a get-request or get-next-request, the agent
always returns 'ready' for this value. Setting the
value to 'ready' has no effect. Setting it to
'execute' causes the port's counters to be zeroed.
Corresponds to the ZERO PORT command."
::= { basicPortEntry 28 }
[Page 26]
XYPLEX CHARACTER MIB 18 Oct 91
basicPortZeroTime OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of hundredths of a second since the most
recent zeroing of the port's counters, such as
through execution of basicPortZero. Corresponds
directly to the value labeled 'Seconds Since
Zeroed:' in the PORT COUNTERS display."
::= { basicPortEntry 29 }
[Page 27]
XYPLEX CHARACTER MIB 18 Oct 91
-- the Basic Serial Port table
basicSerialPortTable OBJECT-TYPE
SYNTAX SEQUENCE OF BasicSerialPortEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of basic character serial port entries."
::= { basic 18 }
basicSerialPortEntry OBJECT-TYPE
SYNTAX BasicSerialPortEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Basic parameter values for a serial port."
INDEX { basicSerialPortIndex }
::= { basicSerialPortTable 1 }
BasicSerialPortEntry ::=
SEQUENCE {
basicSerialPortIndex
INTEGER,
basicSerialPortBreak
INTEGER,
basicSerialPortInterrupts
INTEGER,
basicSerialPortNoLoss
INTEGER,
basicSerialPortPause
INTEGER,
basicSerialPortPrompt
DisplayString,
basicSerialPortTerminalType
INTEGER,
basicSerialPortTypeaheadLimit
INTEGER,
basicSerialPortBackwardSwitch
INTEGER,
basicSerialPortForwardSwitch
INTEGER,
basicSerialPortLocalSwitch
INTEGER,
basicSerialPortModemControl
INTEGER,
basicSerialPortSignalCheck
[Page 28]
XYPLEX CHARACTER MIB 18 Oct 91
INTEGER,
basicSerialPortDSRLogout
INTEGER,
basicSerialPortDSRObserve
INTEGER,
basicSerialPortDCDTimeout
INTEGER,
basicSerialPortDTRAssert
INTEGER,
basicSerialPortLimitedCommands
INTEGER,
basicSerialPortLimitedView
INTEGER,
basicSerialPortPassword
DisplayString,
basicSerialPortLineEditor
INTEGER,
basicSerialPortLineEditorBackspace
INTEGER,
basicSerialPortLineEditorBeginning
INTEGER,
basicSerialPortLineEditorCancel
INTEGER,
basicSerialPortLineEditorDeleteBeginning
INTEGER,
basicSerialPortLineEditorDeleteLine
INTEGER,
basicSerialPortLineEditorEnd
INTEGER,
basicSerialPortLineEditorForward
INTEGER,
basicSerialPortLineEditorInsertToggle
INTEGER,
basicSerialPortLineEditorNextLine
INTEGER,
basicSerialPortLineEditorPreviousLine
INTEGER,
basicSerialPortLineEditorQuotingCharacter
INTEGER,
basicSerialPortLineEditorRedisplay
INTEGER
}
basicSerialPortIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
[Page 29]
XYPLEX CHARACTER MIB 18 Oct 91
STATUS mandatory
DESCRIPTION
"An index value that uniquely identifies a port.
The port identified by a particular value of this
index is the same port as identified by
charPortIndex in the Character MIB [12]."
::= { basicSerialPortEntry 1 }
basicSerialPortBreak OBJECT-TYPE
SYNTAX INTEGER { ignore(1), localSwitch(2),
sendRemote(3) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Action to take on a BREAK condition from the port.
Corresponds directly to PORT BREAK and the value
labeled 'Break:' in the PORT CHARACTERISTICS
display."
::= { basicSerialPortEntry 2 }
basicSerialPortInterrupts OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for recognizing BREAK or local switch to
interrupt a session. Corresponds directly to PORT
INTERRUPTS and the presence of the label
'Interrupts' following the label 'Enabled
Characteristics:' in the PORT CHARACTERISTICS
display."
::= { basicSerialPortEntry 3 }
basicSerialPortNoLoss OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for storing port input locally in
anticipation of session startup. Corresponds
directly to PORT NOLOSS and the presence of the
label 'Noloss' following the label 'Enabled
Characteristics:' in the PORT CHARACTERISTICS
display."
::= { basicSerialPortEntry 4 }
[Page 30]
XYPLEX CHARACTER MIB 18 Oct 91
basicSerialPortPause OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for pausing after each screenful of
locally-originated output to the port. Corresponds
directly to PORT PAUSE and the presence of the label
'Pause' following the label 'Enabled
Characteristics:' in the PORT CHARACTERISTICS
display."
::= { basicSerialPortEntry 5 }
basicSerialPortPrompt OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..8))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Prompt for the system to use on the port.
Corresponds directly to PORT PROMPT and the value
labeled 'Prompt:' in the PORT ALTERNATE
CHARACTERISTICS display."
::= { basicSerialPortEntry 6 }
basicSerialPortTerminalType OBJECT-TYPE
SYNTAX INTEGER { ansi(1), hardcopy(2), softcopy(3) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Type of terminal attached to the port, for
formatting local output. Corresponds directly to
PORT TYPE and the value labeled 'Type:' in the PORT
CHARACTERISTICS display."
::= { basicSerialPortEntry 7 }
basicSerialPortTypeaheadLimit OBJECT-TYPE
SYNTAX INTEGER (80..16384)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Maximum number of input characters to hold pending
tranmission on a session. Corresponds directly to
PORT TYPEAHEAD SIZE and the value labeled 'Typeahead
Size:' in the PORT ALTERNATE CHARACTERISTICS
display."
::= { basicSerialPortEntry 8 }
[Page 31]
XYPLEX CHARACTER MIB 18 Oct 91
basicSerialPortBackwardSwitch OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Character input from the character port to cause a
switch to the previous, lower numbered session. The
value 0 indicates no character has this effect.
Corresponds directly to PORT BACKWARD SWITCH and the
value labeled 'Backwards Switch:' in the PORT
CHARACTERISTICS display."
::= { basicSerialPortEntry 9 }
basicSerialPortForwardSwitch OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Character input from the character port to cause a
switch to the next, higher numbered session. The
value 0 indicates no character has this effect.
Corresponds directly to PORT FORWARD SWITCH and the
value labeled 'Forwards Switch:' in the PORT
CHARACTERISTICS display."
::= { basicSerialPortEntry 10 }
basicSerialPortLocalSwitch OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Character input from the character port to cause a
switch to local command mode. The value 0 indicates
no character has this effect. Corresponds directly
to PORT LOCAL SWITCH and the value labeled 'Local
Switch:' in the PORT CHARACTERISTICS display."
::= { basicSerialPortEntry 11 }
basicSerialPortModemControl OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
[Page 32]
XYPLEX CHARACTER MIB 18 Oct 91
"Control for observing hardware modem control
signals. Corresponds directly to PORT MODEM CONTROL
and the value labeled 'Modem Control:' in the PORT
CHARACTERISTICS display."
::= { basicSerialPortEntry 12 }
basicSerialPortSignalCheck OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for observing DSR and DCD to bound allowing
sessions. Corresponds directly to PORT SIGNAL CHECK
and the presence of the label 'Signal Check'
following the label 'Enabled Characteristics:' in
the PORT CHARACTERISTICS display."
::= { basicSerialPortEntry 13 }
basicSerialPortDSRLogout OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for logging out the port when DCD is
deasserted. Corresponds directly to PORT DSRLOGOUT
and the presence of the label 'DSRlogout' following
the label 'Enabled Characteristics:' in the PORT
CHARACTERISTICS display."
::= { basicSerialPortEntry 14 }
basicSerialPortDSRObserve OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for beginning the login sequence on the
port when DCD is asserted. Corresponds directly to
PORT DSRWAIT and the presence of the label 'DSRwait'
following the label 'Enabled Characteristics:' in
the PORT CHARACTERISTICS display."
::= { basicSerialPortEntry 15 }
basicSerialPortDCDTimeout OBJECT-TYPE
SYNTAX INTEGER (0..10000)
ACCESS read-write
STATUS mandatory
[Page 33]
XYPLEX CHARACTER MIB 18 Oct 91
DESCRIPTION
"The number of milleseconds that DCD may be asserted
before disconnecting the port. Corresponds directly
to PORT DCD TIMEOUT and the value labeled 'DCD
Timeout:' in the PORT ALTERNATE CHARACTERISTICS
display."
::= { basicSerialPortEntry 16 }
basicSerialPortDTRAssert OBJECT-TYPE
SYNTAX INTEGER { always(1), onConnectionOrRing(2),
onConnection(3), onRing(4) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control when the system asserts DTR on the port.
always unconditional(DISABLED)
onConnectionOrRing connection formed or RING
asserted(ENABLED)
onConnection connection formed
(FORCONNECTION)
onRing RING asserted (FORRING)
Corresponds directly to PORT DTRWAIT and the value
labeled 'DTR Wait:' in the PORT ALTERNATE
CHARACTERISTICS display."
::= { basicSerialPortEntry 17 }
basicSerialPortLimitedCommands OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for limiting the commands available to the
user on the port. Corresponds directly to PORT
SECURITY and the presence of the label 'Security'
following the label 'Enabled Characteristics:' in
the PORT CHARACTERISTICS display."
::= { basicSerialPortEntry 18 }
basicSerialPortLimitedView OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for restricting what a user may display.
[Page 34]
XYPLEX CHARACTER MIB 18 Oct 91
Corresponds directly to PORT LIMITED VIEW and the
presence of the label 'Limited View' following the
label 'Enabled Characteristics:' in the PORT
CHARACTERISTICS display."
::= { basicSerialPortEntry 19 }
basicSerialPortPassword OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for requiring the user to supply the login
password to log in on the port. Corresponds
directly to PORT PASSWORD and the presence of the
label 'Password' following the label 'Enabled
Characteristics:' in the PORT CHARACTERISTICS
display."
::= { basicSerialPortEntry 20 }
basicSerialPortLineEditor OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for allowing the user to use local mode
command line editing. Corresponds directly to PORT
LINE EDITOR and the presence of the label 'Line
Editor' following the label 'Enabled
Characteristics:' in the PORT CHARACTERISTICS
display."
::= { basicSerialPortEntry 21 }
-- Note that the values for the switching and
-- line editing characters are mutally exclusive
basicSerialPortLineEditorBackspace OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Character input from the character port to move the
cursor to the left. The value 0 indicates no
character has this effect. Corresponds directly to
PORT LINE EDITOR BACKSPACE and the value labeled
'Backspace Character:' in the PORT ALTERNATE
CHARACTERISTICS display."
[Page 35]
XYPLEX CHARACTER MIB 18 Oct 91
::= { basicSerialPortEntry 22 }
basicSerialPortLineEditorBeginning OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Character input from the character port to move the
cursor to the beginning of the line. The value 0
indicates no character has this effect. Corresponds
directly to PORT LINE EDITOR BEGINNING and the value
labeled 'Begin Line Character:' in the PORT
ALTERNATE CHARACTERISTICS display."
::= { basicSerialPortEntry 23 }
basicSerialPortLineEditorCancel OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Character input from the character port to cancel
an interactive dialog or delete the current line.
The value 0 indicates no character has this effect.
Corresponds directly to PORT LINE EDITOR CANCEL and
the value labeled 'Cancel Character:' in the PORT
ALTERNATE CHARACTERISTICS display."
::= { basicSerialPortEntry 24 }
basicSerialPortLineEditorDeleteBeginning OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Character input from the character port to delete
the current line from the cursor to the beginning.
The value 0 indicates no character has this effect.
Corresponds directly to PORT LINE EDITOR DELETE
BEGINNING and the value labeled 'Delete Begin
Character:' in the PORT ALTERNATE CHARACTERISTICS
display."
::= { basicSerialPortEntry 25 }
basicSerialPortLineEditorDeleteLine OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
[Page 36]
XYPLEX CHARACTER MIB 18 Oct 91
DESCRIPTION
"Character input from the character port to delete
the current line. The value 0 indicates no
character has this effect. Corresponds directly to
PORT LINE EDITOR DELETE LINE and the value labeled
'Delete Line Character:' in the PORT ALTERNATE
CHARACTERISTICS display."
::= { basicSerialPortEntry 26 }
basicSerialPortLineEditorEnd OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Character input from the character port to move the
cursor to the end of the line. The value 0
indicates no character has this effect. Corresponds
directly to PORT LINE EDITOR END and the value
labeled 'End of Line Character:' in the PORT
ALTERNATE CHARACTERISTICS display."
::= { basicSerialPortEntry 27 }
basicSerialPortLineEditorForward OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Character input from the character port to move the
cursor to the right. The value 0 indicates no
character has this effect. Corresponds directly to
PORT LINE EDITOR FORWARDS and the value labeled
'Forwards Character:' in the PORT ALTERNATE
CHARACTERISTICS display."
::= { basicSerialPortEntry 28 }
basicSerialPortLineEditorInsertToggle OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Character input from the character port to toggle
between insert and overwrite modes. The value 0
indicates no character has this effect. Corresponds
directly to PORT LINE EDITOR INSERT TOGGLE and the
value labeled 'Insert Character:' in the PORT
ALTERNATE CHARACTERISTICS display."
[Page 37]
XYPLEX CHARACTER MIB 18 Oct 91
::= { basicSerialPortEntry 29 }
basicSerialPortLineEditorNextLine OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Character input from the character port to recall
the next, newer line in the command history. The
value -1 indicates no character has this effect.
Corresponds directly to PORT LINE EDITOR NEXT LINE
and the value labeled 'Next Line Character:' in the
PORT ALTERNATE CHARACTERISTICS display."
::= { basicSerialPortEntry 30 }
basicSerialPortLineEditorPreviousLine OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Character input from the character port to recall
the previous, older line in the command history.
The value 0 indicates no character has this effect.
Corresponds directly to PORT LINE EDITOR PREVIOUS
LINE and the value labeled 'Previous Line
Character:' in the PORT ALTERNATE CHARACTERISTICS
display."
::= { basicSerialPortEntry 31 }
basicSerialPortLineEditorQuotingCharacter OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Character input from the character port to inhibit
interpretation of the next input character. The
value 0 indicates no character has this effect.
Corresponds directly to PORT LINE EDITOR QUOTING
CHARACTER and the value labeled 'Quoting Character:'
in the PORT ALTERNATE CHARACTERISTICS display."
::= { basicSerialPortEntry 32 }
basicSerialPortLineEditorRedisplay OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
[Page 38]
XYPLEX CHARACTER MIB 18 Oct 91
DESCRIPTION
"Character input from the character port to
redisplay the current command line. The value 0
indicates no character has this effect. Corresponds
directly to PORT LINE EDITOR REDISPLAY CHARACTER and
the value labeled 'Redisplay Character:' in the PORT
ALTERNATE CHARACTERISTICS display."
::= { basicSerialPortEntry 33 }
[Page 39]
XYPLEX CHARACTER MIB 18 Oct 91
-- the Basic group continued
basicConsoleLogoutDisconnect OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for automatic session disconnection when a
console port user logs out. Corresponds directly to
SERVER CONSOLE LOGOUT and the presence of the label
'Console Logout' following the label 'Enabled
Characteristics:' in the SERVER CHARACTERISTICS
display."
::= { basic 19 }
[Page 40]
XYPLEX CHARACTER MIB 18 Oct 91
-- the Queue group
-- Implementation of this group is mandatory for all Xyplex
-- systems that implement port queueing
queueLimit OBJECT-TYPE
SYNTAX INTEGER (-1..100)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The maximum number of entries that can be made in
the Queue table. The value -1 indicates the imit is
available memory. Corresponds directly to SERVER
QUEUE LIMIT and the value labeled 'Queue Limit:' in
the SERVER CHARACTERISTICS display."
::= { queue 1 }
queueHigh OBJECT-TYPE
SYNTAX Gauge
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The highest value of queueNumber since system
initialization. Corresponds directly to the value
labeled 'Queue Entries' and 'High' in the SERVER
STATUS display."
::= { queue 2 }
queueNumber OBJECT-TYPE
SYNTAX Gauge
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of entries in the Queue table.
Corresponds directly to the value labeled 'Queue
Entries' and 'Cur' in the SERVER STATUS display."
::= { queue 3 }
[Page 41]
XYPLEX CHARACTER MIB 18 Oct 91
-- The Queue table
queueTable OBJECT-TYPE
SYNTAX SEQUENCE OF QueueEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of queue entries."
::= { queue 4 }
queueEntry OBJECT-TYPE
SYNTAX QueueEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Parameter values for a queue entry."
INDEX { queueJob }
::= { queueTable 1 }
QueueEntry ::=
SEQUENCE {
queueJob
INTEGER,
queueStatus
INTEGER,
queueSourceName
DisplayString,
queueServiceName
DisplayString,
queueServicePortIndex
INTEGER,
queueServicePortName
DisplayString
}
queueJob OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The job number of a queued request. Corresponds
directly to the value labeled 'Entry' in the QUEUE
display."
::= { queueEntry 1 }
queueStatus OBJECT-TYPE
[Page 42]
XYPLEX CHARACTER MIB 18 Oct 91
SYNTAX INTEGER { invalid(1), valid(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The status of a queue entry. Set to 'invalid' to
remove the entry, which corresponds directly to the
REMOVE QUEUE ENTRY command. Actual removal of the
entry is implementation specific."
::= { queueEntry 2 }
queueSourceName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..50))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The name of the system that originated the queue
entry. Corresponds directly to the value labeled
'Source Node' in the QUEUE display."
::= { queueEntry 3 }
queueServiceName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..16))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The name of the service for which the originator is
waiting. Corresponds directly to the value labeled
'Service' in the QUEUE display."
::= { queueEntry 4 }
queueServicePortIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The charPortIndex of the port for which the
originator is waiting, if supplied by the
originator. As defined in the Character MIB [12].
Corresponds indirectly to the port number part of
the value labeled 'Port Name' in the QUEUE
display."
::= { queueEntry 5 }
queueServicePortName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..16))
ACCESS read-only
[Page 43]
XYPLEX CHARACTER MIB 18 Oct 91
STATUS mandatory
DESCRIPTION
"The name of the port for which the originator is
waiting, if supplied by the originator. Corresponds
directly to the port name part of the value labeled
'Port Name' in the SERVER QUEUE display."
::= { queueEntry 6 }
[Page 44]
XYPLEX CHARACTER MIB 18 Oct 91
-- the Queue Port table
queuePortTable OBJECT-TYPE
SYNTAX SEQUENCE OF QueuePortEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of queuing-related character port entries."
::= { queue 5 }
queuePortEntry OBJECT-TYPE
SYNTAX QueuePortEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Queuing parameter values for a port."
INDEX { queuePortIndex }
::= { queuePortTable 1 }
QueuePortEntry ::=
SEQUENCE {
queuePortIndex
INTEGER,
queuePortQueuing
INTEGER
}
queuePortIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An index value that uniquely identifies a port.
The port identified by a particular value of this
index is the same port as identified by
charPortIndex in the Character MIB [12]."
::= { queuePortEntry 1 }
queuePortQueuing OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for allowing queued requests for using the
port. Corresponds directly to PORT QUEUING and the
presence of the label 'Queuing' following the label
[Page 45]
XYPLEX CHARACTER MIB 18 Oct 91
'Enabled Characteristics:' in the PORT
CHARACTERISTICS display."
::= { queuePortEntry 2 }
[Page 46]
XYPLEX CHARACTER MIB 18 Oct 91
-- the Menu group
-- Implementation of this group is mandatory for all Xyplex
-- systems that implement user menus
menuNumber OBJECT-TYPE
SYNTAX Gauge
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of entries in the Menu table.
Corresponds indirectly to SERVER MENU display."
::= { menu 1 }
menuContinuePrompt OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..50))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The text to use when prompting a menu user to press
RETURN to continue. Corresponds directly to SERVER
MENU CONTINUE PROMPT and the value labeled 'Menu
Continue Prompt:' in the SERVER MENU display."
::= { menu 2 }
menuSelectionPrompt OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..50))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The text to use when prompting a menu user for a
menu selection. Corresponds directly to SERVER MENU
PROMPT and the value labeled 'Menu Prompt:' in the
SERVER MENU display."
::= { menu 3 }
[Page 47]
XYPLEX CHARACTER MIB 18 Oct 91
-- The Menu table
menuTable OBJECT-TYPE
SYNTAX SEQUENCE OF MenuEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of menu entries."
::= { menu 4 }
menuEntry OBJECT-TYPE
SYNTAX MenuEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Parameter values for a menu entry."
INDEX { menuIndex }
::= { menuTable 1 }
MenuEntry ::=
SEQUENCE {
menuIndex
INTEGER,
menuStatus
INTEGER,
menuText
DisplayString,
menuCommand
DisplayString
}
menuIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The index number of a menu entry. Corresponds
directly to the numbers down the left of the SERVER
MENU display."
::= { menuEntry 1 }
menuStatus OBJECT-TYPE
SYNTAX INTEGER { invalid(1), valid(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
[Page 48]
XYPLEX CHARACTER MIB 18 Oct 91
"The status of a the entry. Set to 'invalid' to
remove the entry, which corresponds directly to the
CLEAR SERVER MENU command. Actual removal of the
entry is implementation specific."
DEFVAL { valid }
::= { menuEntry 2 }
menuText OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..30))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The text to be displayed in the menu. Corresponds
directly to the line next to the entry number in the
SERVER MENU display."
::= { menuEntry 3 }
menuCommand OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The commands to execute when the user chooses the
menu entry. Corresponds directly second line
following the entry number in the SERVER MENU
display."
::= { menuEntry 4 }
[Page 49]
XYPLEX CHARACTER MIB 18 Oct 91
-- the Menu Port table
menuPortTable OBJECT-TYPE
SYNTAX SEQUENCE OF MenuPortEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of menu-related character port entries."
::= { menu 5 }
menuPortEntry OBJECT-TYPE
SYNTAX MenuPortEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Menu parameter values for a port."
INDEX { menuPortIndex }
::= { menuPortTable 1 }
MenuPortEntry ::=
SEQUENCE {
menuPortIndex
INTEGER,
menuPortMenuStatus
INTEGER
}
menuPortIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An index value that uniquely identifies a port.
The port identified by a particular value of this
index is the same port as identified by
charPortIndex in the Character MIB [12]."
::= { menuPortEntry 1 }
menuPortMenuStatus OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2), privileged(3) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for menu operation on the port.
Corresponds indirectly to PORT MENU and PORT
PRIVILEGED MENU and the presence of the labels
[Page 50]
XYPLEX CHARACTER MIB 18 Oct 91
'Menu' and 'Privileged Men' following the label
'Enabled Characteristics:' in the PORT
CHARACTERISTICS display."
::= { menuPortEntry 2 }
[Page 51]
XYPLEX CHARACTER MIB 18 Oct 91
-- the Network Login group
-- Implementation of this group is mandatory for all Xyplex
-- systems that implement network login
netLoginNumber OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of entries in the Network Login Server
table."
::= { netLogin 1 }
[Page 52]
XYPLEX CHARACTER MIB 18 Oct 91
-- The Network Login Server table
netLoginServerTable OBJECT-TYPE
SYNTAX SEQUENCE OF NetLoginServerEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of network login server entries."
::= { netLogin 2 }
netLoginServerEntry OBJECT-TYPE
SYNTAX NetLoginServerEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Network login parameter values for a server
entry."
INDEX { netLoginServerName }
::= { netLoginServerTable 1 }
NetLoginServerEntry ::=
SEQUENCE {
netLoginServerName
DisplayString,
netLoginServerStatus
INTEGER,
netLoginServerPath
DisplayString
}
netLoginServerName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..50))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The name of a network login server, suitable for
resolution to a network address. Corresponds
directly to host portion of SERVER SCRIPT SERVER and
the value labeled 'Script Host' in the SERVER
PARAMETER SERVER display."
::= { netLoginServerEntry 1 }
netLoginServerStatus OBJECT-TYPE
SYNTAX INTEGER { invalid(1), valid(2) }
ACCESS read-write
STATUS mandatory
[Page 53]
XYPLEX CHARACTER MIB 18 Oct 91
DESCRIPTION
"Status of this entry. Set to 'invalid'to remove the entry, which
corresponds directly to the CLEAR SERVER SCRIPT SERVER
command. Acutal removal of the entry is implementation
specific."
DEFVAL { valid }
::= { netLoginServerEntry 2 }
netLoginServerPath OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..40))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The full path name to the script file that is
identified by the user name. Corresponds directly
to path portion of SERVER SCRIPT SERVER and the
value labeled 'Script Path' in the SERVER PARAMETER
SERVER display."
::= { netLoginServerEntry 3 }
[Page 54]
XYPLEX CHARACTER MIB 18 Oct 91
-- the Network Login Port table
netLoginPortTable OBJECT-TYPE
SYNTAX SEQUENCE OF NetLoginPortEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of network login character port entries."
::= { netLogin 3 }
netLoginPortEntry OBJECT-TYPE
SYNTAX NetLoginPortEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Network login parameter values for a port."
INDEX { netLoginPortIndex }
::= { netLoginPortTable 1 }
NetLoginPortEntry ::=
SEQUENCE {
netLoginPortIndex
INTEGER,
netLoginPortScriptUse
INTEGER,
netLoginPortScriptEcho
INTEGER,
netLoginPortLoaderAddressType
INTEGER,
netLoginPortLoaderAddress
OCTET STRING,
netLoginPortLoaderFile
DisplayString
}
netLoginPortIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An index value that uniquely identifies a port.
The port identified by a particular value of this
index is the same port as identified by
charPortIndex in the Character MIB [12]."
::= { netLoginPortEntry 1 }
[Page 55]
XYPLEX CHARACTER MIB 18 Oct 91
netLoginPortScriptUse OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2), required(3) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for the script action taken when a user
logs in on the port. Corresponds directly to PORT
SCRIPT LOGIN and the value labeled 'Script Login:'
in the PORT ALTERNATE CHARACTERISTICS display."
::= { netLoginPortEntry 2 }
netLoginPortScriptEcho OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Control for display of script operation on the port
when running a script. Corresponds directly to PORT
SCRIPT ECHO and the presence of the label 'Script
Echo' following the label 'Enabled Characteristics:'
in the PORT CHARACTERISTICS display."
::= { netLoginPortEntry 3 }
netLoginPortLoaderAddressType OBJECT-TYPE
SYNTAX AddressType
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The type of network address contained in
netLoginPortLoaderAddress. 'unknown' means no
address has been defined. 'other' means no other
type value applies. 'ip' is an Internet IP address.
'ethernet' is an 802.3 MAC address. Corresponds
indirectly to the address part of the value labeled
'Script Loaded From:' in the PORT STATUS display."
::= { netLoginPortEntry 4 }
netLoginPortLoaderAddress OBJECT-TYPE
SYNTAX OCTET STRING
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The network address of the server that provided the
script for the current port login. Corresponds
directly the address part of the value labeled
'Script Loaded From:' in the PORT STATUS display."
[Page 56]
XYPLEX CHARACTER MIB 18 Oct 91
::= { netLoginPortEntry 5 }
netLoginPortLoaderFile OBJECT-TYPE
SYNTAX DisplayString
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The path and file name of the script used for the
current port login. Corresponds directly the file
name part of the value labeled 'Script Loaded
From:' in the PORT STATUS display."
::= { netLoginPortEntry 6 }
[Page 57]
XYPLEX CHARACTER MIB 18 Oct 91
-- the Dial group
-- Implementation of this group is mandatory for all Xyplex
-- systems that implement automatic dialing
dialPortTable OBJECT-TYPE
SYNTAX SEQUENCE OF DialPortEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of dial character port entries."
::= { dial 1 }
dialPortEntry OBJECT-TYPE
SYNTAX DialPortEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Dial parameter values for a port."
INDEX { dialPortIndex }
::= { dialPortTable 1 }
DialPortEntry ::=
SEQUENCE {
dialPortIndex
INTEGER,
dialPortDialback
INTEGER,
dialPortDialbackTimeout
INTEGER
}
dialPortIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An index value that uniquely identifies a port.
The port identified by a particular value of this
index is the same port as identified by
charPortIndex in the Character MIB [12]."
::= { dialPortEntry 1 }
dialPortDialback OBJECT-TYPE
SYNTAX INTEGER { disabled(1), enabled(2) }
ACCESS read-write
[Page 58]
XYPLEX CHARACTER MIB 18 Oct 91
STATUS mandatory
DESCRIPTION
"Control for use of dialback when a user logs in on
the port. Corresponds directly to PORT DIALBACK and
the presence of the label 'Dialback' following the
label 'Enabled Characteristics:' in the PORT
CHARACTERISTICS display."
::= { dialPortEntry 2 }
dialPortDialbackTimeout OBJECT-TYPE
SYNTAX INTEGER (5..60)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The number of seconds to wait for remote modem
response when dialing back. Corresponds directly to
PORT DIALBACK TIMEOUT and the value labeled
'Dialback Timeout:' in the PORT ALTERNATE
CHARACTERISTICS display."
::= { dialPortEntry 3 }
[Page 59]
XYPLEX CHARACTER MIB 18 Oct 91
-- the Session Log group
-- Implementation of this group is mandatory for all Xyplex
-- systems that implement logging session information
sessionLogLimit OBJECT-TYPE
SYNTAX INTEGER (0..1000)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"The maximum number of entries allowed in the
Session Log table. Corresponds directly to SERVER
ACCOUNTING ENTRIES and the value labeled 'Accounting
Entries:' in the SERVER CHARACTERISTICS display."
::= { sessionLog 1 }
[Page 60]
XYPLEX CHARACTER MIB 18 Oct 91
-- The Session Log table
sessionLogTable OBJECT-TYPE
SYNTAX SEQUENCE OF SessionLogEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of session log entries."
::= { sessionLog 2 }
sessionLogEntry OBJECT-TYPE
SYNTAX SessionLogEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Parameter values for a session log entry."
INDEX { sessionLogIndex }
::= { sessionLogTable 1 }
SessionLogEntry ::=
SEQUENCE {
sessionLogIndex
INTEGER,
sessionLogConnectionID
INTEGER,
sessionLogPort
INTEGER,
sessionLogEvent
INTEGER,
sessionLogEventDetail
INTEGER,
sessionLogUserName
DisplayString,
sessionLogRemoteName
DisplayString,
sessionLogConnectTime
DateTime,
sessionLogDisconnectTime
DateTime,
sessionLogInCharacters
Counter,
sessionLogOutCharacters
Counter
}
sessionLogIndex OBJECT-TYPE
[Page 61]
XYPLEX CHARACTER MIB 18 Oct 91
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The index number of a session log entry.
Corresponds directly to the order of the displayed
records in the SERVER ACCOUNTING display. The
maximum value is sessionLogLimit."
::= { sessionLogEntry 1 }
sessionLogConnectionID OBJECT-TYPE
SYNTAX INTEGER (1..65535)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An indentifying number for records relating to the
same connection, that is, the connect and disconnect
records, either of which can be missing.
Corresponds directly to value labeled 'Entry' the
SERVER ACCOUNTING display."
::= { sessionLogEntry 2 }
sessionLogPort OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An index value that uniquely identifies the port
where the event took place. The port identified by
a particular value of this index is the same port as
identified by charPortIndex in the Character MIB
[12]. Corresponds directly to the value labeled
'Port' in the SERVER ACCOUNTING display."
::= { sessionLogEntry 3 }
sessionLogEvent OBJECT-TYPE
SYNTAX INTEGER { login(1), connectLocal(2),
connectRemote(3), disconnect(4) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The type of event. Corresponds directly to the
alphabetic part of the value labeled 'Type' in the
SERVER ACCOUNTING display."
::= { sessionLogEntry 4 }
[Page 62]
XYPLEX CHARACTER MIB 18 Oct 91
sessionLogEventDetail OBJECT-TYPE
SYNTAX INTEGER { none(1), protocolBadCircuit(2),
protocolBadCredits(3),
protocolBadStartOrRun(4),
protocolBadRange(5),
duplicateQueueID(6), noUsers(7),
noServiceResourced(8),
serviceUserDisconnect(9),
serviceUnavailable(10),
serverUserDisconnect(11),
noNodeResources(12),
systemShutdown(13),
nodeUserdisconnect(14),
badCircuitTimer(15),
badServiceClass(16),
badMessageOrSlot(17),
timeout(18), noProgress(19),
serviceNotOnPort(20), noSuchPort(21),
badPassword(22), serviceBusy(23),
noSuchService(24),
serviceDisabled(25),
notInQueue(26), noImmeditatAccess(27),
accessDenied(28),
protocolBadSolicit(29),
protocolBadReasonCode(30),
unsupportedTest(31),
domainTooLong(32),
noSuchNode(33),
noSuchServiceOnNode(34),
rejectService(35),
internetConnectDisabled(36) }
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The detailed reason for the event. Corresponds
directly to the numeric part of the value labeled
'Type' in the SERVER ACCOUNTING display."
::= { sessionLogEntry 5 }
sessionLogUserName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..16))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The user name logged in on the port when the event
occurred. Corresponds directly to the value labeled
[Page 63]
XYPLEX CHARACTER MIB 18 Oct 91
'Username' in the SERVER ACCOUNTING display."
::= { sessionLogEntry 6 }
sessionLogRemoteName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..16))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The name of the session remote partner.
Corresponds directly to the value labeled
'Destination' in the SERVER ACCOUNTING display."
::= { sessionLogEntry 7 }
sessionLogConnectTime OBJECT-TYPE
SYNTAX DateTime
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The date and time that session connection occurred.
Corresponds directly to the value labeled 'Connect
Time' in the SERVER ACCOUNTING display."
::= { sessionLogEntry 8 }
sessionLogDisconnectTime OBJECT-TYPE
SYNTAX DateTime
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The date and time that session disconnection
occurred. Corresponds directly to the value labeled
'Disconnect Time' in the SERVER ACCOUNTING
display."
::= { sessionLogEntry 9 }
sessionLogInCharacters OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of characters that came into the port
for the session. Corresponds directly to the value
labeled 'Bytes In' in the SERVER ACCOUNTING
display."
::= { sessionLogEntry 10 }
sessionLogOutCharacters OBJECT-TYPE
[Page 64]
XYPLEX CHARACTER MIB 18 Oct 91
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The number of characters that went out of the port
for the session. Corresponds directly to the value
labeled 'Bytes Out' in the SERVER ACCOUNTING
display."
::= { sessionLogEntry 11 }
END
[Page 65]
XYPLEX CHARACTER MIB 18 Oct 91
7. References
[1] V. Cerf, IAB Recommendations for the Development of
Internet Network Management Standards. Internet Working
Group Request for Comments 1052. Network Information
Center, SRI International, Menlo Park, California, (April,
1988).
[2] V. Cerf, Report of the Second Ad Hoc Network Management
Review Group, Internet Working Group Request for Comments
1109. Network Information Center, SRI International, Menlo
Park, California, (August, 1989).
[3] M.T. Rose (editor), Management Information Base for
Network Management of TCP/IP-based internets, Internet
Working Group Request for Comments 1158. Network
Information Center, SRI International, Menlo Park,
California, (May, 1990).
[4] M.T. Rose and K. McCloghrie, Structure and
Identification of Management Information for TCP/IP-based
internets, Internet Working Group Request for Comments 1155.
Network Information Center, SRI International, Menlo Park,
California, (May, 1990).
[5] K. McCloghrie and M.T. Rose, Management Information
Base for Network Management of TCP/IP-based
internets:MIB-II, Internet Working Group Request for
Comments 1213. Network Information Center, SRI
International, Menlo Park, California, (March 1991).
[6] J.D. Case, M.S. Fedor, M.L. Schoffstall, and J.R.
Davin, Simple Network Management Protocol, Internet Working
Group Request for Comments 1157. Network Information
Center, SRI International, Menlo Park, California, (May,
1990).
[7] Information processing systems - Open Systems
Interconnection - Specification of Abstract Syntax Notation
One (ASN.1), International Organization for Standardization.
International Standard 8824, (December, 1987).
[8] Information processing systems - Open Systems
Interconnection - Specification of Basic Encoding Rules for
Abstract Notation One (ASN.1), International Organization
for Standardization. International Standard 8825,
[Page 66]
XYPLEX CHARACTER MIB 18 Oct 91
(December, 1987).
[9] M.T. Rose, K. McCloghrie (editors), Towards Concise MIB
Definitions, Internet Working Group Request for Comments
1212. Network Information Center, SRI International, Menlo
Park, California, (March, 1991).
[10] Definitions of Managed Objects for Xyplex Systems,
Xyplex document number 420-0545, (August, 1991).
[11] Xyplex Minimal MIB Architectural Specification, Xyplex
document number 420-0333, (15 November 1990).
[12] B. Stewart (editor), Definitions of Managed Objects for
Character Stream Devices, Internet Draft, (19 March 1991).
[Page 67]