LINUX ALLOCATED DEVICES Maintained by H. Peter Anvin Last revised: December 29, 2000 This list is the Linux Device List, the official registry of allocated device numbers and /dev directory nodes for the Linux operating system. The latest version of this list is included with the Linux kernel sources. It is also available separately from http://www.kernel.org/pub/linux/docs/device-list/ or ftp://ftp.kernel.org/pub/linux/docs/device-list/. The LaTeX version of this document is no longer maintained. This document is included by reference into the Filesystem Hierarchy Standard (FHS). The FHS is available from http://www.pathname.com/fhs/. Allocations marked (68k/Amiga) apply to Linux/68k on the Amiga platform only. Allocations marked (68k/Atari) apply to Linux/68k on the Atari platform only. The symbol {2.6} means the allocation is obsolete and scheduled for removal once kernel version 2.6 (or equivalent) is released. This document is in the public domain. The author requests, however, that semantically altered versions are not distributed without permission of the author, assuming the author can be contacted without an unreasonable effort. In particular, please don't sent patches for this list to Linus, at least not without contacting me first. I do not have any information about these devices beyond what appears on this list. Any such information requests will be deleted without reply. **** DEVICE DRIVERS AUTHORS PLEASE READ THIS **** To have a major number allocated, or a minor number in situations where that applies (e.g. busmice), please contact me with the appropriate device information. Also, if you have additional information regarding any of the devices listed below, or if I have made a mistake, I would greatly appreciate a note. I do, however, make a few requests about the nature of your report. This is necessary for me to be able to keep this list up to date and correct in a timely manner. First of all, *please* send it to the correct address... . I receive hundreds of email messages a day, so mail sent to other addresses may very well get lost in the avalanche. Please put in a descriptive subject, so I can find your mail again should I need to. Too many people send me email saying just "device number request" in the subject. Second, please include a description of the device *in the same format as this list*. The reason for this is that it is the only way I have found to ensure I have all the requisite information to publish your device and avoid conflicts. Third, please don't assume that the distributed version of the list is up to date. Due to the number of registrations I have to maintain it in "batch mode", so there is likely additional registrations that haven't been listed yet. Finally, sometimes I have to play "namespace police." Please don't be offended. I often get submissions for /dev names that would be bound to cause conflicts down the road. I am trying to avoid getting in a situation where we would have to suffer an incompatible forward change. Therefore, please consult with me *before* you make your device names and numbers in any way public, at least to the point where it would be at all difficult to get them changed. Your cooperation is appreciated. 0 Unnamed devices (e.g. non-device mounts) 0 = reserved as null device number 1 char Memory devices 1 = /dev/mem Physical memory access 2 = /dev/kmem Kernel virtual memory access 3 = /dev/null Null device 4 = /dev/port I/O port access 5 = /dev/zero Null byte source 6 = /dev/core OBSOLETE - replaced by /proc/kcore 7 = /dev/full Returns ENOSPC on write 8 = /dev/random Nondeterministic random number gen. 9 = /dev/urandom Faster, less secure random number gen. 10 = /dev/aio Asyncronous I/O notification interface block RAM disk 0 = /dev/ram0 First RAM disk 1 = /dev/ram1 Second RAM disk ... 250 = /dev/initrd Initial RAM disk {2.6} Older kernels had /dev/ramdisk (1, 1) here. /dev/initrd refers to a RAM disk which was preloaded by the boot loader; newer kernels use /dev/ram0 for the initrd. 2 char Pseudo-TTY masters 0 = /dev/ptyp0 First PTY master 1 = /dev/ptyp1 Second PTY master ... 255 = /dev/ptyef 256th PTY master Pseudo-tty's are named as follows: * Masters are "pty", slaves are "tty"; * the fourth letter is one of pqrstuvwxyzabcde indicating the 1st through 16th series of 16 pseudo-ttys each, and * the fifth letter is one of 0123456789abcdef indicating the position within the series. These are the old-style (BSD) PTY devices; Unix98 devices are on major 128 and above and use the PTY master multiplex (/dev/ptmx) to acquire a PTY on demand. block Floppy disks 0 = /dev/fd0 Controller 0, drive 0, autodetect 1 = /dev/fd1 Controller 0, drive 1, autodetect 2 = /dev/fd2 Controller 0, drive 2, autodetect 3 = /dev/fd3 Controller 0, drive 3, autodetect 128 = /dev/fd4 Controller 1, drive 0, autodetect 129 = /dev/fd5 Controller 1, drive 1, autodetect 130 = /dev/fd6 Controller 1, drive 2, autodetect 131 = /dev/fd7 Controller 1, drive 3, autodetect To specify format, add to the autodetect device number: 0 = /dev/fd? Autodetect format 4 = /dev/fd?d360 5.25" 360K in a 360K drive(1) 20 = /dev/fd?h360 5.25" 360K in a 1200K drive(1) 48 = /dev/fd?h410 5.25" 410K in a 1200K drive 64 = /dev/fd?h420 5.25" 420K in a 1200K drive 24 = /dev/fd?h720 5.25" 720K in a 1200K drive 80 = /dev/fd?h880 5.25" 880K in a 1200K drive(1) 8 = /dev/fd?h1200 5.25" 1200K in a 1200K drive(1) 40 = /dev/fd?h1440 5.25" 1440K in a 1200K drive(1) 56 = /dev/fd?h1476 5.25" 1476K in a 1200K drive 72 = /dev/fd?h1494 5.25" 1494K in a 1200K drive 92 = /dev/fd?h1600 5.25" 1600K in a 1200K drive(1) 12 = /dev/fd?u360 3.5" 360K Double Density(2) 16 = /dev/fd?u720 3.5" 720K Double Density(1) 120 = /dev/fd?u800 3.5" 800K Double Density(2) 52 = /dev/fd?u820 3.5" 820K Double Density 68 = /dev/fd?u830 3.5" 830K Double Density 84 = /dev/fd?u1040 3.5" 1040K Double Density(1) 88 = /dev/fd?u1120 3.5" 1120K Double Density(1) 28 = /dev/fd?u1440 3.5" 1440K High Density(1) 124 = /dev/fd?u1600 3.5" 1600K High Density(1) 44 = /dev/fd?u1680 3.5" 1680K High Density(3) 60 = /dev/fd?u1722 3.5" 1722K High Density 76 = /dev/fd?u1743 3.5" 1743K High Density 96 = /dev/fd?u1760 3.5" 1760K High Density 116 = /dev/fd?u1840 3.5" 1840K High Density(3) 100 = /dev/fd?u1920 3.5" 1920K High Density(1) 32 = /dev/fd?u2880 3.5" 2880K Extra Density(1) 104 = /dev/fd?u3200 3.5" 3200K Extra Density 108 = /dev/fd?u3520 3.5" 3520K Extra Density 112 = /dev/fd?u3840 3.5" 3840K Extra Density(1) 36 = /dev/fd?CompaQ Compaq 2880K drive; obsolete? (1) Autodetectable format (2) Autodetectable format in a Double Density (720K) drive only (3) Autodetectable format in a High Density (1440K) drive only NOTE: The letter in the device name (d, q, h or u) signifies the type of drive: 5.25" Double Density (d), 5.25" Quad Density (q), 5.25" High Density (h) or 3.5" (any model, u). The use of the capital letters D, H and E for the 3.5" models have been deprecated, since the drive type is insignificant for these devices. 3 char Pseudo-TTY slaves 0 = /dev/ttyp0 First PTY slave 1 = /dev/ttyp1 Second PTY slave ... 255 = /dev/ttyef 256th PTY slave These are the old-style (BSD) PTY devices; Unix98 devices are on major 136 and above. block First MFM, RLL and IDE hard disk/CD-ROM interface 0 = /dev/hda Master: whole disk (or CD-ROM) 64 = /dev/hdb Slave: whole disk (or CD-ROM) For partitions, add to the whole disk device number: 0 = /dev/hd? Whole disk 1 = /dev/hd?1 First partition 2 = /dev/hd?2 Second partition ... 63 = /dev/hd?63 63rd partition For Linux/i386, partitions 1-4 are the primary partitions, and 5 and above are logical partitions. Other versions of Linux use partitioning schemes appropriate to their respective architectures. 4 char TTY devices 0 = /dev/tty0 Current virtual console 1 = /dev/tty1 First virtual console ... 63 = /dev/tty63 63rd virtual console 64 = /dev/ttyS0 First UART serial port ... 255 = /dev/ttyS191 192nd UART serial port UART serial ports refer to 8250/16450/16550 series devices. Older versions of the Linux kernel used this major number for BSD PTY devices. As of Linux 2.1.115, this is no longer supported. Use major numbers 2 and 3. 5 char Alternate TTY devices 0 = /dev/tty Current TTY device 1 = /dev/console System console 2 = /dev/ptmx PTY master multiplex 64 = /dev/cua0 Callout device for ttyS0 ... 255 = /dev/cua191 Callout device for ttyS191 (5,1) is /dev/console starting with Linux 2.1.71. See the section on terminal devices for more information on /dev/console. 6 char Parallel printer devices 0 = /dev/lp0 Parallel printer on parport0 1 = /dev/lp1 Parallel printer on parport1 ... Current Linux kernels no longer have a fixed mapping between parallel ports and I/O addresses. Instead, they are redirected through the parport multiplex layer. 7 char Virtual console capture devices 0 = /dev/vcs Current vc text contents 1 = /dev/vcs1 tty1 text contents ... 63 = /dev/vcs63 tty63 text contents 128 = /dev/vcsa Current vc text/attribute contents 129 = /dev/vcsa1 tty1 text/attribute contents ... 191 = /dev/vcsa63 tty63 text/attribute contents NOTE: These devices permit both read and write access. block Loopback devices 0 = /dev/loop0 First loopback device 1 = /dev/loop1 Second loopback device ... The loopback devices are used to mount filesystems not associated with block devices. The binding to the loopback devices is handled by mount(8) or losetup(8). 8 block SCSI disk devices (0-15) 0 = /dev/sda First SCSI disk whole disk 16 = /dev/sdb Second SCSI disk whole disk 32 = /dev/sdc Third SCSI disk whole disk ... 240 = /dev/sdp Sixteenth SCSI disk whole disk Partitions are handled in the same way as for IDE disks (see major number 3) except that the limit on partitions is 15. 9 char SCSI tape devices 0 = /dev/st0 First SCSI tape, mode 0 1 = /dev/st1 Second SCSI tape, mode 0 ... 32 = /dev/st0l First SCSI tape, mode 1 33 = /dev/st1l Second SCSI tape, mode 1 ... 64 = /dev/st0m First SCSI tape, mode 2 65 = /dev/st1m Second SCSI tape, mode 2 ... 96 = /dev/st0a First SCSI tape, mode 3 97 = /dev/st1a Second SCSI tape, mode 3 ... 128 = /dev/nst0 First SCSI tape, mode 0, no rewind 129 = /dev/nst1 Second SCSI tape, mode 0, no rewind ... 160 = /dev/nst0l First SCSI tape, mode 1, no rewind 161 = /dev/nst1l Second SCSI tape, mode 1, no rewind ... 192 = /dev/nst0m First SCSI tape, mode 2, no rewind 193 = /dev/nst1m Second SCSI tape, mode 2, no rewind ... 224 = /dev/nst0a First SCSI tape, mode 3, no rewind 225 = /dev/nst1a Second SCSI tape, mode 3, no rewind ... "No rewind" refers to the omission of the default automatic rewind on device close. The MTREW or MTOFFL ioctl()'s can be used to rewind the tape regardless of the device used to access it. block Metadisk (RAID) devices 0 = /dev/md0 First metadisk group 1 = /dev/md1 Second metadisk group ... The metadisk driver is used to span a filesystem across multiple physical disks. 10 char Non-serial mice, misc features 0 = /dev/logibm Logitech bus mouse 1 = /dev/psaux PS/2-style mouse port 2 = /dev/inportbm Microsoft Inport bus mouse 3 = /dev/atibm ATI XL bus mouse 4 = /dev/jbm J-mouse 4 = /dev/amigamouse Amiga mouse (68k/Amiga) 5 = /dev/atarimouse Atari mouse 6 = /dev/sunmouse Sun mouse 7 = /dev/amigamouse1 Second Amiga mouse 8 = /dev/smouse Simple serial mouse driver 9 = /dev/pc110pad IBM PC-110 digitizer pad 10 = /dev/adbmouse Apple Desktop Bus mouse 11 = /dev/vrtpanel Vr41xx embedded touch panel 13 = /dev/vpcmouse Connectix Virtual PC Mouse 14 = /dev/touchscreen/ucb1x00 UCB 1x00 touchscreen 15 = /dev/touchscreen/mk712 MK712 touchscreen 128 = /dev/beep Fancy beep device 129 = /dev/modreq Kernel module load request {2.6} 130 = /dev/watchdog Watchdog timer port 131 = /dev/temperature Machine internal temperature 132 = /dev/hwtrap Hardware fault trap 133 = /dev/exttrp External device trap 134 = /dev/apm_bios Advanced Power Management BIOS 135 = /dev/rtc Real Time Clock 139 = /dev/openprom SPARC OpenBoot PROM 140 = /dev/relay8 Berkshire Products Octal relay card 141 = /dev/relay16 Berkshire Products ISO-16 relay card 142 = /dev/msr x86 model-specific registers {2.6} 143 = /dev/pciconf PCI configuration space 144 = /dev/nvram Non-volatile configuration RAM 145 = /dev/hfmodem Soundcard shortwave modem control {2.6} 146 = /dev/graphics Linux/SGI graphics device 147 = /dev/opengl Linux/SGI OpenGL pipe 148 = /dev/gfx Linux/SGI graphics effects device 149 = /dev/input/mouse Linux/SGI Irix emulation mouse 150 = /dev/input/keyboard Linux/SGI Irix emulation keyboard 151 = /dev/led Front panel LEDs 153 = /dev/mergemem Memory merge device 154 = /dev/pmu Macintosh PowerBook power manager 155 = /dev/isictl MultiTech ISICom serial control 156 = /dev/lcd Front panel LCD display 157 = /dev/ac Applicom Intl Profibus card 158 = /dev/nwbutton Netwinder external button 159 = /dev/nwdebug Netwinder debug interface 160 = /dev/nwflash Netwinder flash memory 161 = /dev/userdma User-space DMA access 162 = /dev/smbus System Management Bus 163 = /dev/lik Logitech Internet Keyboard 164 = /dev/ipmo Intel Intelligent Platform Management 165 = /dev/vmmon VMWare virtual machine monitor 166 = /dev/i2o/ctl I2O configuration manager 167 = /dev/specialix_sxctl Specialix serial control 168 = /dev/tcldrv Technology Concepts serial control 169 = /dev/specialix_rioctl Specialix RIO serial control 170 = /dev/smapi IBM Thinkpad SMAPI 171 = /dev/srripc QNX4 API IPC manager 172 = /dev/usemaclone Semaphore clone device 173 = /dev/ipmikcs Intelligent Platform Management 174 = /dev/uctrl SPARCbook 3 microcontroller 175 = /dev/agpgart AGP Graphics Address Remapping Table 176 = /dev/gtrsc Gorgy Timing radio clock 177 = /dev/cbm Serial CBM bus 178 = /dev/jsflash JavaStation OS flash SIMM 179 = /dev/xsvc High-speed shared-mem/semaphore service 180 = /dev/vrbuttons Vr41xx button input device 181 = /dev/toshiba Toshiba laptop SMM support 182 = /dev/perfctr Performance-monitoring counters 183 = /dev/intel_rng Intel i8x0 random number generator 184 = /dev/cpu/microcode CPU microcode update interface 186 = /dev/atomicps Atomic shapshot of process state data 187 = /dev/irnet IrNET device 188 = /dev/smbusbios SMBus BIOS 189 = /dev/ussp_ctl User space serial port control 190 = /dev/crash Mission Critical Linux crash dump facility 191 = /dev/pcl181 192 = /dev/nas_xbus NAS xbus LCD/buttons access 193 = /dev/d7s SPARC 7-segment display 194 = /dev/zkshim Zero-Knowledge network shim control 195 = /dev/elographics/e2201 Elographics touchscreen E271-2201 198 = /dev/sexec Signed executable interface 199 = /dev/scanners/cuecat :CueCat barcode scanner 200 = /dev/net/tun TAP/TUN network device 201 = /dev/button/gulpb Transmeta GULP-B buttons 204 = /dev/video/em8300 EM8300 DVD decoder control 205 = /dev/video/em8300_mv EM8300 DVD decoder video 206 = /dev/video/em8300_ma EM8300 DVD decoder audio 207 = /dev/video/em8300_sp EM8300 DVD decoder subpicture 208 = /dev/compaq/cpqphpc Compaq PCI Hot Plug Controller 209 = /dev/compaq/cpqrid Compaq Remote Insight Driver 240-255 Reserved for local use 11 char Raw keyboard device 0 = /dev/kbd Raw keyboard device The raw keyboard device is used on Linux/SPARC only. block SCSI CD-ROM devices 0 = /dev/sr0 First SCSI CD-ROM 1 = /dev/sr1 Second SCSI CD-ROM ... The prefix /dev/scd instead of /dev/sr has been used as well, and might make more sense. 12 char QIC-02 tape 2 = /dev/ntpqic11 QIC-11, no rewind-on-close 3 = /dev/tpqic11 QIC-11, rewind-on-close 4 = /dev/ntpqic24 QIC-24, no rewind-on-close 5 = /dev/tpqic24 QIC-24, rewind-on-close 6 = /dev/ntpqic120 QIC-120, no rewind-on-close 7 = /dev/tpqic120 QIC-120, rewind-on-close 8 = /dev/ntpqic150 QIC-150, no rewind-on-close 9 = /dev/tpqic150 QIC-150, rewind-on-close The device names specified are proposed -- if there are "standard" names for these devices, please let me know. block MSCDEX CD-ROM callback support {2.6} 0 = /dev/dos_cd0 First MSCDEX CD-ROM 1 = /dev/dos_cd1 Second MSCDEX CD-ROM ... 13 char PC speaker (OBSOLETE) 0 = /dev/pcmixer Emulates /dev/mixer 1 = /dev/pcsp Emulates /dev/dsp (8-bit) 4 = /dev/pcaudio Emulates /dev/audio 5 = /dev/pcsp16 Emulates /dev/dsp (16-bit) The current PC speaker driver uses the Open Sound System interface, and these devices are obsolete. block 8-bit MFM/RLL/IDE controller 0 = /dev/xda First XT disk whole disk 64 = /dev/xdb Second XT disk whole disk Partitions are handled in the same way as IDE disks (see major number 3). 14 char Open Sound System (OSS) 0 = /dev/mixer Mixer control 1 = /dev/sequencer Audio sequencer 2 = /dev/midi00 First MIDI port 3 = /dev/dsp Digital audio 4 = /dev/audio Sun-compatible digital audio 6 = /dev/sndstat Sound card status information {2.6} 7 = /dev/audioctl SPARC audio control device 8 = /dev/sequencer2 Sequencer -- alternate device 16 = /dev/mixer1 Second soundcard mixer control 17 = /dev/patmgr0 Sequencer patch manager 18 = /dev/midi01 Second MIDI port 19 = /dev/dsp1 Second soundcard digital audio 20 = /dev/audio1 Second soundcard Sun digital audio 33 = /dev/patmgr1 Sequencer patch manager 34 = /dev/midi02 Third MIDI port 50 = /dev/midi03 Fourth MIDI port block BIOS harddrive callback support {2.6} 0 = /dev/dos_hda First BIOS harddrive whole disk 64 = /dev/dos_hdb Second BIOS harddrive whole disk 128 = /dev/dos_hdc Third BIOS harddrive whole disk 192 = /dev/dos_hdd Fourth BIOS harddrive whole disk Partitions are handled in the same way as IDE disks (see major number 3). 15 char Joystick 0 = /dev/js0 First analog joystick 1 = /dev/js1 Second analog joystick ... 128 = /dev/djs0 First digital joystick 129 = /dev/djs1 Second digital joystick ... block Sony CDU-31A/CDU-33A CD-ROM 0 = /dev/sonycd Sony CDU-31a CD-ROM 16 char Non-SCSI scanners 0 = /dev/gs4500 Genius 4500 handheld scanner block GoldStar CD-ROM 0 = /dev/gscd GoldStar CD-ROM 17 char Chase serial card 0 = /dev/ttyH0 First Chase port 1 = /dev/ttyH1 Second Chase port ... block Optics Storage CD-ROM 0 = /dev/optcd Optics Storage CD-ROM 18 char Chase serial card - alternate devices 0 = /dev/cuh0 Callout device for ttyH0 1 = /dev/cuh1 Callout device for ttyH1 ... block Sanyo CD-ROM 0 = /dev/sjcd Sanyo CD-ROM 19 char Cyclades serial card 0 = /dev/ttyC0 First Cyclades port ... 31 = /dev/ttyC31 32nd Cyclades port block "Double" compressed disk 0 = /dev/double0 First compressed disk ... 7 = /dev/double7 Eighth compressed disk 128 = /dev/cdouble0 Mirror of first compressed disk ... 135 = /dev/cdouble7 Mirror of eighth compressed disk See the Double documentation for the meaning of the mirror devices. 20 char Cyclades serial card - alternate devices 0 = /dev/cub0 Callout device for ttyC0 ... 31 = /dev/cub31 Callout device for ttyC31 block Hitachi CD-ROM (under development) 0 = /dev/hitcd Hitachi CD-ROM 21 char Generic SCSI access 0 = /dev/sg0 First generic SCSI device 1 = /dev/sg1 Second generic SCSI device ... Most distributions name these /dev/sga, /dev/sgb...; this sets an unnecessary limit of 26 SCSI devices in the system and is counter to standard Linux device-naming practice. block Acorn MFM hard drive interface 0 = /dev/mfma First MFM drive whole disk 64 = /dev/mfmb Second MFM drive whole disk This device is used on the ARM-based Acorn RiscPC. Partitions are handled the same way as for IDE disks (see major number 3). 22 char Digiboard serial card 0 = /dev/ttyD0 First Digiboard port 1 = /dev/ttyD1 Second Digiboard port ... block Second IDE hard disk/CD-ROM interface 0 = /dev/hdc Master: whole disk (or CD-ROM) 64 = /dev/hdd Slave: whole disk (or CD-ROM) Partitions are handled the same way as for the first interface (see major number 3). 23 char Digiboard serial card - alternate devices 0 = /dev/cud0 Callout device for ttyD0 1 = /dev/cud1 Callout device for ttyD1 ... block Mitsumi proprietary CD-ROM 0 = /dev/mcd Mitsumi CD-ROM 24 char Stallion serial card 0 = /dev/ttyE0 Stallion port 0 card 0 1 = /dev/ttyE1 Stallion port 1 card 0 ... 64 = /dev/ttyE64 Stallion port 0 card 1 65 = /dev/ttyE65 Stallion port 1 card 1 ... 128 = /dev/ttyE128 Stallion port 0 card 2 129 = /dev/ttyE129 Stallion port 1 card 2 ... 192 = /dev/ttyE192 Stallion port 0 card 3 193 = /dev/ttyE193 Stallion port 1 card 3 ... block Sony CDU-535 CD-ROM 0 = /dev/cdu535 Sony CDU-535 CD-ROM 25 char Stallion serial card - alternate devices 0 = /dev/cue0 Callout device for ttyE0 1 = /dev/cue1 Callout device for ttyE1 ... 64 = /dev/cue64 Callout device for ttyE64 65 = /dev/cue65 Callout device for ttyE65 ... 128 = /dev/cue128 Callout device for ttyE128 129 = /dev/cue129 Callout device for ttyE129 ... 192 = /dev/cue192 Callout device for ttyE192 193 = /dev/cue193 Callout device for ttyE193 ... block First Matsushita (Panasonic/SoundBlaster) CD-ROM 0 = /dev/sbpcd0 Panasonic CD-ROM controller 0 unit 0 1 = /dev/sbpcd1 Panasonic CD-ROM controller 0 unit 1 2 = /dev/sbpcd2 Panasonic CD-ROM controller 0 unit 2 3 = /dev/sbpcd3 Panasonic CD-ROM controller 0 unit 3 26 char Quanta WinVision frame grabber {2.6} 0 = /dev/wvisfgrab Quanta WinVision frame grabber block Second Matsushita (Panasonic/SoundBlaster) CD-ROM 0 = /dev/sbpcd4 Panasonic CD-ROM controller 1 unit 0 1 = /dev/sbpcd5 Panasonic CD-ROM controller 1 unit 1 2 = /dev/sbpcd6 Panasonic CD-ROM controller 1 unit 2 3 = /dev/sbpcd7 Panasonic CD-ROM controller 1 unit 3 27 char QIC-117 tape 0 = /dev/qft0 Unit 0, rewind-on-close 1 = /dev/qft1 Unit 1, rewind-on-close 2 = /dev/qft2 Unit 2, rewind-on-close 3 = /dev/qft3 Unit 3, rewind-on-close 4 = /dev/nqft0 Unit 0, no rewind-on-close 5 = /dev/nqft1 Unit 1, no rewind-on-close 6 = /dev/nqft2 Unit 2, no rewind-on-close 7 = /dev/nqft3 Unit 3, no rewind-on-close 16 = /dev/zqft0 Unit 0, rewind-on-close, compression 17 = /dev/zqft1 Unit 1, rewind-on-close, compression 18 = /dev/zqft2 Unit 2, rewind-on-close, compression 19 = /dev/zqft3 Unit 3, rewind-on-close, compression 20 = /dev/nzqft0 Unit 0, no rewind-on-close, compression 21 = /dev/nzqft1 Unit 1, no rewind-on-close, compression 22 = /dev/nzqft2 Unit 2, no rewind-on-close, compression 23 = /dev/nzqft3 Unit 3, no rewind-on-close, compression 32 = /dev/rawqft0 Unit 0, rewind-on-close, no file marks 33 = /dev/rawqft1 Unit 1, rewind-on-close, no file marks 34 = /dev/rawqft2 Unit 2, rewind-on-close, no file marks 35 = /dev/rawqft3 Unit 3, rewind-on-close, no file marks 36 = /dev/nrawqft0 Unit 0, no rewind-on-close, no file marks 37 = /dev/nrawqft1 Unit 1, no rewind-on-close, no file marks 38 = /dev/nrawqft2 Unit 2, no rewind-on-close, no file marks 39 = /dev/nrawqft3 Unit 3, no rewind-on-close, no file marks block Third Matsushita (Panasonic/SoundBlaster) CD-ROM 0 = /dev/sbpcd8 Panasonic CD-ROM controller 2 unit 0 1 = /dev/sbpcd9 Panasonic CD-ROM controller 2 unit 1 2 = /dev/sbpcd10 Panasonic CD-ROM controller 2 unit 2 3 = /dev/sbpcd11 Panasonic CD-ROM controller 2 unit 3 28 char Stallion serial card - card programming 0 = /dev/staliomem0 First Stallion card I/O memory 1 = /dev/staliomem1 Second Stallion card I/O memory 2 = /dev/staliomem2 Third Stallion card I/O memory 3 = /dev/staliomem3 Fourth Stallion card I/O memory char Atari SLM ACSI laser printer (68k/Atari) 0 = /dev/slm0 First SLM laser printer 1 = /dev/slm1 Second SLM laser printer ... block Fourth Matsushita (Panasonic/SoundBlaster) CD-ROM 0 = /dev/sbpcd12 Panasonic CD-ROM controller 3 unit 0 1 = /dev/sbpcd13 Panasonic CD-ROM controller 3 unit 1 2 = /dev/sbpcd14 Panasonic CD-ROM controller 3 unit 2 3 = /dev/sbpcd15 Panasonic CD-ROM controller 3 unit 3 block ACSI disk (68k/Atari) 0 = /dev/ada First ACSI disk whole disk 16 = /dev/adb Second ACSI disk whole disk 32 = /dev/adc Third ACSI disk whole disk ... 240 = /dev/adp 16th ACSI disk whole disk Partitions are handled in the same way as for IDE disks (see major number 3) except that the limit on partitions is 15, like SCSI. 29 char Universal frame buffer 0 = /dev/fb0 First frame buffer 1 = /dev/fb1 Second frame buffer ... 31 = /dev/fb31 32nd frame buffer Backward compatibility aliases {2.6} 32 = /dev/fb1 Second frame buffer ... 224 = /dev/fb7 Eighth frame buffer All additional minor numbers are reserved. block Aztech/Orchid/Okano/Wearnes CD-ROM 0 = /dev/aztcd Aztech CD-ROM 30 char iBCS-2 compatibility devices 0 = /dev/socksys Socket access 1 = /dev/spx SVR3 local X interface 2 = /dev/inet/arp Network access 2 = /dev/inet/icmp Network access 2 = /dev/inet/ip Network access 2 = /dev/inet/udp Network access 2 = /dev/inet/tcp Network access Additionally, iBCS-2 requires /dev/nfsd to be a link to /dev/socksys, and /dev/X0R to be a link to /dev/null. block Philips LMS CM-205 CD-ROM 0 = /dev/cm205cd Philips LMS CM-205 CD-ROM /dev/lmscd is an older name for this device. This driver does not work with the CM-205MS CD-ROM. 31 char MPU-401 MIDI 0 = /dev/mpu401data MPU-401 data port 1 = /dev/mpu401stat MPU-401 status port block ROM/flash memory card 0 = /dev/rom0 First ROM card (rw) ... 7 = /dev/rom7 Eighth ROM card (rw) 8 = /dev/rrom0 First ROM card (ro) ... 15 = /dev/rrom7 Eighth ROM card (ro) 16 = /dev/flash0 First flash memory card (rw) ... 23 = /dev/flash7 Eighth flash memory card (rw) 24 = /dev/rflash0 First flash memory card (ro) ... 31 = /dev/rflash7 Eighth flash memory card (ro) The read-write (rw) devices support back-caching written data in RAM, as well as writing to flash RAM devices. The read-only devices (ro) support reading only. 32 char Specialix serial card 0 = /dev/ttyX0 First Specialix port 1 = /dev/ttyX1 Second Specialix port ... block Philips LMS CM-206 CD-ROM 0 = /dev/cm206cd Philips LMS CM-206 CD-ROM 33 char Specialix serial card - alternate devices 0 = /dev/cux0 Callout device for ttyX0 1 = /dev/cux1 Callout device for ttyX1 ... block Third IDE hard disk/CD-ROM interface 0 = /dev/hde Master: whole disk (or CD-ROM) 64 = /dev/hdf Slave: whole disk (or CD-ROM) Partitions are handled the same way as for the first interface (see major number 3). 34 char Z8530 HDLC driver 0 = /dev/scc0 First Z8530, first port 1 = /dev/scc1 First Z8530, second port 2 = /dev/scc2 Second Z8530, first port 3 = /dev/scc3 Second Z8530, second port ... In a previous version these devices were named /dev/sc1 for /dev/scc0, /dev/sc2 for /dev/scc1, and so on. block Fourth IDE hard disk/CD-ROM interface 0 = /dev/hdg Master: whole disk (or CD-ROM) 64 = /dev/hdh Slave: whole disk (or CD-ROM) Partitions are handled the same way as for the first interface (see major number 3). 35 char tclmidi MIDI driver 0 = /dev/midi0 First MIDI port, kernel timed 1 = /dev/midi1 Second MIDI port, kernel timed 2 = /dev/midi2 Third MIDI port, kernel timed 3 = /dev/midi3 Fourth MIDI port, kernel timed 64 = /dev/rmidi0 First MIDI port, untimed 65 = /dev/rmidi1 Second MIDI port, untimed 66 = /dev/rmidi2 Third MIDI port, untimed 67 = /dev/rmidi3 Fourth MIDI port, untimed 128 = /dev/smpte0 First MIDI port, SMPTE timed 129 = /dev/smpte1 Second MIDI port, SMPTE timed 130 = /dev/smpte2 Third MIDI port, SMPTE timed 131 = /dev/smpte3 Fourth MIDI port, SMPTE timed block Slow memory ramdisk 0 = /dev/slram Slow memory ramdisk 36 char Netlink support 0 = /dev/route Routing, device updates, kernel to user 1 = /dev/skip enSKIP security cache control 3 = /dev/fwmonitor Firewall packet copies 16 = /dev/tap0 First Ethertap device ... 31 = /dev/tap15 16th Ethertap device block MCA ESDI hard disk 0 = /dev/eda First ESDI disk whole disk 64 = /dev/edb Second ESDI disk whole disk ... Partitions are handled in the same way as IDE disks (see major number 3). 37 char IDE tape 0 = /dev/ht0 First IDE tape 1 = /dev/ht1 Second IDE tape ... 128 = /dev/nht0 First IDE tape, no rewind-on-close 129 = /dev/nht1 Second IDE tape, no rewind-on-close ... Currently, only one IDE tape drive is supported. block Zorro II ramdisk 0 = /dev/z2ram Zorro II ramdisk 38 char Myricom PCI Myrinet board 0 = /dev/mlanai0 First Myrinet board 1 = /dev/mlanai1 Second Myrinet board ... This device is used for status query, board control and "user level packet I/O." This board is also accessible as a standard networking "eth" device. block Reserved for Linux/AP+ 39 char ML-16P experimental I/O board 0 = /dev/ml16pa-a0 First card, first analog channel 1 = /dev/ml16pa-a1 First card, second analog channel ... 15 = /dev/ml16pa-a15 First card, 16th analog channel 16 = /dev/ml16pa-d First card, digital lines 17 = /dev/ml16pa-c0 First card, first counter/timer 18 = /dev/ml16pa-c1 First card, second counter/timer 19 = /dev/ml16pa-c2 First card, third counter/timer 32 = /dev/ml16pb-a0 Second card, first analog channel 33 = /dev/ml16pb-a1 Second card, second analog channel ... 47 = /dev/ml16pb-a15 Second card, 16th analog channel 48 = /dev/ml16pb-d Second card, digital lines 49 = /dev/ml16pb-c0 Second card, first counter/timer 50 = /dev/ml16pb-c1 Second card, second counter/timer 51 = /dev/ml16pb-c2 Second card, third counter/timer ... block Reserved for Linux/AP+ 40 char Matrox Meteor frame grabber {2.6} 0 = /dev/mmetfgrab Matrox Meteor frame grabber block Syquest EZ135 parallel port removable drive 0 = /dev/eza Parallel EZ135 drive, whole disk This device is obsolete and will be removed in a future version of Linux. It has been replaced with the parallel port IDE disk driver at major number 45. Partitions are handled in the same way as IDE disks (see major number 3). 41 char Yet Another Micro Monitor 0 = /dev/yamm Yet Another Micro Monitor block MicroSolutions BackPack parallel port CD-ROM 0 = /dev/bpcd BackPack CD-ROM This device is obsolete and will be removed in a future version of Linux. It has been replaced with the parallel port ATAPI CD-ROM driver at major number 46. 42 Demo/sample use This number is intended for use in sample code, as well as a general "example" device number. It should never be used for a device driver that is being distributed; either obtain an official number or use the local/experimental range. The sudden addition or removal of a driver with this number should not cause ill effects to the system (bugs excepted.) IN PARTICULAR, ANY DISTRIBUTION WHICH CONTAINS A DEVICE DRIVER USING MAJOR NUMBER 42 IS NONCOMPLIANT. 43 char isdn4linux virtual modem 0 = /dev/ttyI0 First virtual modem ... 63 = /dev/ttyI63 64th virtual modem block Network block devices 0 = /dev/nb0 First network block device 1 = /dev/nb1 Second network block device ... Network Block Device is somehow similar to loopback devices: If you read from it, it sends packet accross network asking server for data. If you write to it, it sends packet telling server to write. It could be used to mounting filesystems over the net, swapping over the net, implementing block device in userland etc. 44 char isdn4linux virtual modem - alternate devices 0 = /dev/cui0 Callout device for ttyI0 ... 63 = /dev/cui63 Callout device for ttyI63 block Flash Translatio Layer (FTL) filesystems 0 = /dev/ftla FTL on first Memory Technology Device 16 = /dev/ftlb FTL on second Memory Technology Device 32 = /dev/ftlc FTL on third Memory Technology Device ... 240 = /dev/ftlp FTL on 16th Memory Technology Device Partitions are handled in the same way as for IDE disks (see major number 3) expect that the partition limit is 15 rather than 63 per disk (same as SCSI.) 45 char isdn4linux ISDN BRI driver 0 = /dev/isdn0 First virtual B channel raw data ... 63 = /dev/isdn63 64th virtual B channel raw data 64 = /dev/isdnctrl0 First channel control/debug ... 127 = /dev/isdnctrl63 64th channel control/debug 128 = /dev/ippp0 First SyncPPP device ... 191 = /dev/ippp63 64th SyncPPP device 255 = /dev/isdninfo ISDN monitor interface block Parallel port IDE disk devices 0 = /dev/pda First parallel port IDE disk 16 = /dev/pdb Second parallel port IDE disk 32 = /dev/pdc Third parallel port IDE disk 48 = /dev/pdd Fourth parallel port IDE disk Partitions are handled in the same way as for IDE disks (see major number 3) except that the partition limit is 15 rather than 63 per disk. 46 char Comtrol Rocketport serial card 0 = /dev/ttyR0 First Rocketport port 1 = /dev/ttyR1 Second Rocketport port ... block Parallel port ATAPI CD-ROM devices 0 = /dev/pcd0 First parallel port ATAPI CD-ROM 1 = /dev/pcd1 Second parallel port ATAPI CD-ROM 2 = /dev/pcd2 Third parallel port ATAPI CD-ROM 3 = /dev/pcd3 Fourth parallel port ATAPI CD-ROM 47 char Comtrol Rocketport serial card - alternate devices 0 = /dev/cur0 Callout device for ttyR0 1 = /dev/cur1 Callout device for ttyR1 ... block Parallel port ATAPI disk devices 0 = /dev/pf0 First parallel port ATAPI disk 1 = /dev/pf1 Second parallel port ATAPI disk 2 = /dev/pf2 Third parallel port ATAPI disk 3 = /dev/pf3 Fourth parallel port ATAPI disk This driver is intended for floppy disks and similar devices and hence does not support partitioning. 48 char SDL RISCom serial card 0 = /dev/ttyL0 First RISCom port 1 = /dev/ttyL1 Second RISCom port ... block Mylex DAC960 PCI RAID controller; first controller 0 = /dev/rd/c0d0 First disk, whole disk 8 = /dev/rd/c0d1 Second disk, whole disk ... 248 = /dev/rd/c0d15 16th disk, whole disk For partitions add: 0 = /dev/rd/c?d? Whole disk 1 = /dev/rd/c?d?p1 First partition ... 7 = /dev/rd/c?d?p7 Seventh partition 49 char SDL RISCom serial card - alternate devices 0 = /dev/cul0 Callout device for ttyL0 1 = /dev/cul1 Callout device for ttyL1 ... block Mylex DAC960 PCI RAID controller; second controller 0 = /dev/rd/c1d0 First disk, whole disk 8 = /dev/rd/c1d1 Second disk, whole disk ... 248 = /dev/rd/c1d15 16th disk, whole disk Partitions are handled as for major 48. 50 char Reserved for GLINT block Mylex DAC960 PCI RAID controller; third controller 0 = /dev/rd/c2d0 First disk, whole disk 8 = /dev/rd/c2d1 Second disk, whole disk ... 248 = /dev/rd/c2d15 16th disk, whole disk 51 char Baycom radio modem 0 = /dev/bc0 First Baycom radio modem 1 = /dev/bc1 Second Baycom radio modem ... block Mylex DAC960 PCI RAID controller; fourth controller 0 = /dev/rd/c3d0 First disk, whole disk 8 = /dev/rd/c3d1 Second disk, whole disk ... 248 = /dev/rd/c3d15 16th disk, whole disk Partitions are handled as for major 48. 52 char Spellcaster DataComm/BRI ISDN card 0 = /dev/dcbri0 First DataComm card 1 = /dev/dcbri1 Second DataComm card 2 = /dev/dcbri2 Third DataComm card 3 = /dev/dcbri3 Fourth DataComm card block Mylex DAC960 PCI RAID controller; fifth controller 0 = /dev/rd/c4d0 First disk, whole disk 8 = /dev/rd/c4d1 Second disk, whole disk ... 248 = /dev/rd/c4d15 16th disk, whole disk Partitions are handled as for major 48. 53 char BDM interface for remote debugging MC683xx microcontrollers 0 = /dev/pd_bdm0 PD BDM interface on lp0 1 = /dev/pd_bdm1 PD BDM interface on lp1 2 = /dev/pd_bdm2 PD BDM interface on lp2 4 = /dev/icd_bdm0 ICD BDM interface on lp0 5 = /dev/icd_bdm1 ICD BDM interface on lp1 6 = /dev/icd_bdm2 ICD BDM interface on lp2 This device is used for the interfacing to the MC683xx microcontrollers via Background Debug Mode by use of a Parallel Port interface. PD is the Motorola Public Domain Interface and ICD is the commercial interface by P&E. block Mylex DAC960 PCI RAID controller; sixth controller 0 = /dev/rd/c5d0 First disk, whole disk 8 = /dev/rd/c5d1 Second disk, whole disk ... 248 = /dev/rd/c5d15 16th disk, whole disk Partitions are handled as for major 48. 54 char Electrocardiognosis Holter serial card 0 = /dev/holter0 First Holter port 1 = /dev/holter1 Second Holter port 2 = /dev/holter2 Third Holter port A custom serial card used by Electrocardiognosis SRL to transfer data from Holter 24-hour heart monitoring equipment. block Mylex DAC960 PCI RAID controller; seventh controller 0 = /dev/rd/c6d0 First disk, whole disk 8 = /dev/rd/c6d1 Second disk, whole disk ... 248 = /dev/rd/c6d15 16th disk, whole disk Partitions are handled as for major 48. 55 char DSP56001 digital signal processor 0 = /dev/dsp56k First DSP56001 block Mylex DAC960 PCI RAID controller; eigth controller 0 = /dev/rd/c7d0 First disk, whole disk 8 = /dev/rd/c7d1 Second disk, whole disk ... 248 = /dev/rd/c7d15 16th disk, whole disk Partitions are handled as for major 48. 56 char Apple Desktop Bus 0 = /dev/adb ADB bus control Additional devices will be added to this number, all starting with /dev/adb. block Fifth IDE hard disk/CD-ROM interface 0 = /dev/hdi Master: whole disk (or CD-ROM) 64 = /dev/hdj Slave: whole disk (or CD-ROM) Partitions are handled the same way as for the first interface (see major number 3). 57 char Hayes ESP serial card 0 = /dev/ttyP0 First ESP port 1 = /dev/ttyP1 Second ESP port ... block Sixth IDE hard disk/CD-ROM interface 0 = /dev/hdk Master: whole disk (or CD-ROM) 64 = /dev/hdl Slave: whole disk (or CD-ROM) Partitions are handled the same way as for the first interface (see major number 3). 58 char Hayes ESP serial card - alternate devices 0 = /dev/cup0 Callout device for ttyP0 1 = /dev/cup1 Callout device for ttyP1 ... block Reserved for logical volume manager 59 char sf firewall package 0 = /dev/firewall Communication with sf kernel module block Generic PDA filesystem device 0 = /dev/pda0 First PDA device 1 = /dev/pda1 Second PDA device ... The pda devices are used to mount filesystems on remote pda's (basically slow handheld machines with proprietary OS's and limited memory and storage running small fs translation drivers) through serial / IRDA / parallel links. NAMING CONFLICT -- PROPOSED REVISED NAME /dev/rpda0 etc 60-63 LOCAL/EXPERIMENTAL USE Allocated for local/experimental use. For devices not assigned official numbers, these ranges should be used, in order to avoid conflicting with future assignments. 64 char ENskip kernel encryption package 0 = /dev/enskip Communication with ENskip kernel module 65 char Sundance "plink" Transputer boards 0 = /dev/plink0 First plink device 1 = /dev/plink1 Second plink device 2 = /dev/plink2 Third plink device 3 = /dev/plink3 Fourth plink device 64 = /dev/rplink0 First plink device, raw 65 = /dev/rplink1 Second plink device, raw 66 = /dev/rplink2 Third plink device, raw 67 = /dev/rplink3 Fourth plink device, raw 128 = /dev/plink0d First plink device, debug 129 = /dev/plink1d Second plink device, debug 130 = /dev/plink2d Third plink device, debug 131 = /dev/plink3d Fourth plink device, debug 192 = /dev/rplink0d First plink device, raw, debug 193 = /dev/rplink1d Second plink device, raw, debug 194 = /dev/rplink2d Third plink device, raw, debug 195 = /dev/rplink3d Fourth plink device, raw, debug This is a commercial driver; contact James Howes for information. block SCSI disk devices (16-31) 0 = /dev/sdq 16th SCSI disk whole disk 16 = /dev/sdr 17th SCSI disk whole disk 32 = /dev/sds 18th SCSI disk whole disk ... 240 = /dev/sdaf 32nd SCSI disk whole disk Partitions are handled in the same way as for IDE disks (see major number 3) except that the limit on partitions is 15. 66 char YARC PowerPC PCI coprocessor card 0 = /dev/yppcpci0 First YARC card 1 = /dev/yppcpci1 Second YARC card ... block SCSI disk devices (32-47) 0 = /dev/sdag 33th SCSI disk whole disk 16 = /dev/sdah 34th SCSI disk whole disk 32 = /dev/sdai 35th SCSI disk whole disk ... 240 = /dev/sdav 48nd SCSI disk whole disk Partitions are handled in the same way as for IDE disks (see major number 3) except that the limit on partitions is 15. 67 char Coda network file system 0 = /dev/cfs0 Coda cache manager See http://www.coda.cs.cmu.edu for information about Coda. block SCSI disk devices (48-63) 0 = /dev/sdaw 49th SCSI disk whole disk 16 = /dev/sdax 50th SCSI disk whole disk 32 = /dev/sday 51st SCSI disk whole disk ... 240 = /dev/sdbl 64th SCSI disk whole disk Partitions are handled in the same way as for IDE disks (see major number 3) except that the limit on partitions is 15. 68 char CAPI 2.0 interface 0 = /dev/capi20 Control device 1 = /dev/capi20.00 First CAPI 2.0 application 2 = /dev/capi20.01 Second CAPI 2.0 application ... 20 = /dev/capi20.19 19th CAPI 2.0 application ISDN CAPI 2.0 driver for use with CAPI 2.0 applications; currently supports the AVM B1 card. block SCSI disk devices (64-79) 0 = /dev/sdbm 64th SCSI disk whole disk 16 = /dev/sdbn 65th SCSI disk whole disk 32 = /dev/sdbo 66th SCSI disk whole disk ... 240 = /dev/sdcb 80th SCSI disk whole disk Partitions are handled in the same way as for IDE disks (see major number 3) except that the limit on partitions is 15. 69 char MA16 numeric accelerator card 0 = /dev/ma16 Board memory access block SCSI disk devices (80-95) 0 = /dev/sdcc 81st SCSI disk whole disk 16 = /dev/sdcd 82nd SCSI disk whole disk 32 = /dev/sdce 83th SCSI disk whole disk ... 240 = /dev/sdcr 96th SCSI disk whole disk Partitions are handled in the same way as for IDE disks (see major number 3) except that the limit on partitions is 15. 70 char SpellCaster Protocol Services Interface 0 = /dev/apscfg Configuration interface 1 = /dev/apsauth Authentication interface 2 = /dev/apslog Logging interface 3 = /dev/apsdbg Debugging interface 64 = /dev/apsisdn ISDN command interface 65 = /dev/apsasync Async command interface 128 = /dev/apsmon Monitor interface block SCSI disk devices (96-111) 0 = /dev/sdcs 97th SCSI disk whole disk 16 = /dev/sdct 98th SCSI disk whole disk 32 = /dev/sdcu 99th SCSI disk whole disk ... 240 = /dev/sddh 112nd SCSI disk whole disk Partitions are handled in the same way as for IDE disks (see major number 3) except that the limit on partitions is 15. 71 char Computone IntelliPort II serial card 0 = /dev/ttyF0 IntelliPort II board 0, port 0 1 = /dev/ttyF1 IntelliPort II board 0, port 1 ... 63 = /dev/ttyF63 IntelliPort II board 0, port 63 64 = /dev/ttyF64 IntelliPort II board 1, port 0 65 = /dev/ttyF65 IntelliPort II board 1, port 1 ... 127 = /dev/ttyF127 IntelliPort II board 1, port 63 128 = /dev/ttyF128 IntelliPort II board 2, port 0 129 = /dev/ttyF129 IntelliPort II board 2, port 1 ... 191 = /dev/ttyF191 IntelliPort II board 2, port 63 192 = /dev/ttyF192 IntelliPort II board 3, port 0 193 = /dev/ttyF193 IntelliPort II board 3, port 1 ... 255 = /dev/ttyF255 IntelliPort II board 3, port 63 block SCSI disk devices (112-127) 0 = /dev/sddi 113th SCSI disk whole disk 16 = /dev/sddj 114th SCSI disk whole disk 32 = /dev/sddk 115th SCSI disk whole disk ... 240 = /dev/sddx 128th SCSI disk whole disk Partitions are handled in the same way as for IDE disks (see major number 3) except that the limit on partitions is 15. 72 char Computone IntelliPort II serial card - alternate devices 0 = /dev/cuf0 Callout device for ttyF0 1 = /dev/cuf1 Callout device for ttyF1 ... 63 = /dev/cuf63 Callout device for ttyF63 64 = /dev/cuf64 Callout device for ttyF64 65 = /dev/cuf65 Callout device for ttyF65 ... 127 = /dev/cuf127 Callout device for ttyF127 128 = /dev/cuf128 Callout device for ttyF128 129 = /dev/cuf129 Callout device for ttyF129 ... 191 = /dev/cuf191 Callout device for ttyF191 192 = /dev/cuf192 Callout device for ttyF192 193 = /dev/cuf193 Callout device for ttyF193 ... 255 = /dev/cuf255 Callout device for ttyF255 block Compaq Intelligent Drive Array, first controller 0 = /dev/ida/c0d0 First logical drive whole disk 16 = /dev/ida/c0d1 Second logical drive whole disk ... 240 = /dev/ida/c0d15 16th logical drive whole disk Partitions are handled the same way as for Mylex DAC960 (see major number 48) except that the limit on partitions is 15. 73 char Computone IntelliPort II serial card - control devices 0 = /dev/ip2ipl0 Loadware device for board 0 1 = /dev/ip2stat0 Status device for board 0 4 = /dev/ip2ipl1 Loadware device for board 1 5 = /dev/ip2stat1 Status device for board 1 8 = /dev/ip2ipl2 Loadware device for board 2 9 = /dev/ip2stat2 Status device for board 2 12 = /dev/ip2ipl3 Loadware device for board 3 13 = /dev/ip2stat3 Status device for board 3 block Compaq Intelligent Drive Array, second controller 0 = /dev/ida/c1d0 First logical drive whole disk 16 = /dev/ida/c1d1 Second logical drive whole disk ... 240 = /dev/ida/c1d15 16th logical drive whole disk Partitions are handled the same way as for Mylex DAC960 (see major number 48) except that the limit on partitions is 15. 74 char SCI bridge 0 = /dev/SCI/0 SCI device 0 1 = /dev/SCI/1 SCI device 1 ... Currently for Dolphin Interconnect Solutions' PCI-SCI bridge. block Compaq Intelligent Drive Array, third controller 0 = /dev/ida/c2d0 First logical drive whole disk 16 = /dev/ida/c2d1 Second logical drive whole disk ... 240 = /dev/ida/c2d15 16th logical drive whole disk Partitions are handled the same way as for Mylex DAC960 (see major number 48) except that the limit on partitions is 15. 75 char Specialix IO8+ serial card 0 = /dev/ttyW0 First IO8+ port, first card 1 = /dev/ttyW1 Second IO8+ port, first card ... 8 = /dev/ttyW8 First IO8+ port, second card ... block Compaq Intelligent Drive Array, fourth controller 0 = /dev/ida/c3d0 First logical drive whole disk 16 = /dev/ida/c3d1 Second logical drive whole disk ... 240 = /dev/ida/c3d15 16th logical drive whole disk Partitions are handled the same way as for Mylex DAC960 (see major number 48) except that the limit on partitions is 15. 76 char Specialix IO8+ serial card - alternate devices 0 = /dev/cuw0 Callout device for ttyW0 1 = /dev/cuw1 Callout device for ttyW1 ... 8 = /dev/cuw8 Callout device for ttyW8 ... block Compaq Intelligent Drive Array, fifth controller 0 = /dev/ida/c4d0 First logical drive whole disk 16 = /dev/ida/c4d1 Second logical drive whole disk ... 240 = /dev/ida/c4d15 16th logical drive whole disk Partitions are handled the same way as for Mylex DAC960 (see major number 48) except that the limit on partitions is 15. 77 char ComScire Quantum Noise Generator 0 = /dev/qng ComScire Quantum Noise Generator block Compaq Intelligent Drive Array, sixth controller 0 = /dev/ida/c5d0 First logical drive whole disk 16 = /dev/ida/c5d1 Second logical drive whole disk ... 240 = /dev/ida/c5d15 16th logical drive whole disk Partitions are handled the same way as for Mylex DAC960 (see major number 48) except that the limit on partitions is 15. 78 char PAM Software's multimodem boards 0 = /dev/ttyM0 First PAM modem 1 = /dev/ttyM1 Second PAM modem ... block Compaq Intelligent Drive Array, seventh controller 0 = /dev/ida/c6d0 First logical drive whole disk 16 = /dev/ida/c6d1 Second logical drive whole disk ... 240 = /dev/ida/c6d15 16th logical drive whole disk Partitions are handled the same way as for Mylex DAC960 (see major number 48) except that the limit on partitions is 15. 79 char PAM Software's multimodem boards - alternate devices 0 = /dev/cum0 Callout device for ttyM0 1 = /dev/cum1 Callout device for ttyM1 ... block Compaq Intelligent Drive Array, eigth controller 0 = /dev/ida/c7d0 First logical drive whole disk 16 = /dev/ida/c7d1 Second logical drive whole disk ... 240 = /dev/ida/c715 16th logical drive whole disk Partitions are handled the same way as for Mylex DAC960 (see major number 48) except that the limit on partitions is 15. 80 char Photometrics AT200 CCD camera 0 = /dev/at200 Photometrics AT200 CCD camera block I2O hard disk 0 = /dev/i2o/hda First I2O hard disk, whole disk 16 = /dev/i2o/hdb Second I2O hard disk, whole disk ... 240 = /dev/i2o/hdp 16th I2O hard disk, whole disk Partitions are handled in the same way as for IDE disks (see major number 3) except that the limit on partitions is 15. 81 char video4linux 0 = /dev/video0 Video capture/overlay device ... 63 = /dev/video63 Video capture/overlay device 64 = /dev/radio0 Radio device ... 127 = /dev/radio63 Radio device 192 = /dev/vtx0 Teletext device ... 223 = /dev/vtx31 Teletext device 224 = /dev/vbi0 Vertical blank interrupt ... 255 = /dev/vbi31 Vertical blank interrupt block I2O hard disk 0 = /dev/i2o/hdq 17th I2O hard disk, whole disk 16 = /dev/i2o/hdr 18th I2O hard disk, whole disk ... 240 = /dev/i2o/hdaf 32nd I2O hard disk, whole disk Partitions are handled in the same way as for IDE disks (see major number 3) except that the limit on partitions is 15. 82 char WiNRADiO communications receiver card 0 = /dev/winradio0 First WiNRADiO card 1 = /dev/winradio1 Second WiNRADiO card ... The driver and documentation may be obtained from http://www.proximity.com.au/~brian/winradio/ block I2O hard disk 0 = /dev/i2o/hdag 33rd I2O hard disk, whole disk 16 = /dev/i2o/hdah 34th I2O hard disk, whole disk ... 240 = /dev/i2o/hdav 48th I2O hard disk, whole disk Partitions are handled in the same way as for IDE disks (see major number 3) except that the limit on partitions is 15. 83 char Teletext/videotext interfaces {2.6} 0 = /dev/vtx Teletext decoder 16 = /dev/vttuner TV tuner on teletext interface Devices for the driver contained in the VideoteXt package. More information on http://home.pages.de/~videotext/ block I2O hard disk 0 = /dev/i2o/hdaw 49th I2O hard disk, whole disk 16 = /dev/i2o/hdax 50th I2O hard disk, whole disk ... 240 = /dev/i2o/hdbl 64th I2O hard disk, whole disk Partitions are handled in the same way as for IDE disks (see major number 3) except that the limit on partitions is 15. 84 char Ikon 1011[57] Versatec Greensheet Interface 0 = /dev/ihcp0 First Greensheet port 1 = /dev/ihcp1 Second Greensheet port block I2O hard disk 0 = /dev/i2o/hdbm 65th I2O hard disk, whole disk 16 = /dev/i2o/hdbn 66th I2O hard disk, whole disk ... 240 = /dev/i2o/hdcb 80th I2O hard disk, whole disk Partitions are handled in the same way as for IDE disks (see major number 3) except that the limit on partitions is 15. 85 char Linux/SGI shared memory input queue 0 = /dev/shmiq Master shared input queue 1 = /dev/qcntl0 First device pushed 2 = /dev/qcntl1 Second device pushed ... block I2O hard disk 0 = /dev/i2o/hdcc 81st I2O hard disk, whole disk 16 = /dev/i2o/hdcd 82nd I2O hard disk, whole disk ... 240 = /dev/i2o/hdcr 96th I2O hard disk, whole disk Partitions are handled in the same way as for IDE disks (see major number 3) except that the limit on partitions is 15. 86 char SCSI media changer 0 = /dev/sch0 First SCSI media changer 1 = /dev/sch1 Second SCSI media changer ... block I2O hard disk 0 = /dev/i2o/hdcs 97th I2O hard disk, whole disk 16 = /dev/i2o/hdct 98th I2O hard disk, whole disk ... 240 = /dev/i2o/hddh 112th I2O hard disk, whole disk Partitions are handled in the same way as for IDE disks (see major number 3) except that the limit on partitions is 15. 87 char Sony Control-A1 stereo control bus 0 = /dev/controla0 First device on chain 1 = /dev/controla1 Second device on chain ... block I2O hard disk 0 = /dev/i2o/hddi 113rd I2O hard disk, whole disk 16 = /dev/i2o/hddj 114th I2O hard disk, whole disk ... 240 = /dev/i2o/hddx 128th I2O hard disk, whole disk Partitions are handled in the same way as for IDE disks (see major number 3) except that the limit on partitions is 15. 88 char COMX synchronous serial card 0 = /dev/comx0 COMX channel 0 1 = /dev/comx1 COMX channel 1 ... block Seventh IDE hard disk/CD-ROM interface 0 = /dev/hdm Master: whole disk (or CD-ROM) 64 = /dev/hdn Slave: whole disk (or CD-ROM) Partitions are handled the same way as for the first interface (see major number 3). 89 char I2C bus interface 0 = /dev/i2c-0 First I2C adapter 1 = /dev/i2c-1 Second I2C adapter ... block Eighth IDE hard disk/CD-ROM interface 0 = /dev/hdo Master: whole disk (or CD-ROM) 64 = /dev/hdp Slave: whole disk (or CD-ROM) Partitions are handled the same way as for the first interface (see major number 3). 90 char Memory Technology Device (RAM, ROM, Flash) 0 = /dev/mtd0 First MTD (rw) 1 = /dev/mtdr0 First MTD (ro) ... 30 = /dev/mtd15 16th MTD (rw) 31 = /dev/mtdr15 16th MTD (ro) block Ninth IDE hard disk/CD-ROM interface 0 = /dev/hdq Master: whole disk (or CD-ROM) 64 = /dev/hdr Slave: whole disk (or CD-ROM) Partitions are handled the same way as for the first interface (see major number 3). 91 char CAN-Bus devices 0 = /dev/can0 First CAN-Bus controller 1 = /dev/can1 Second CAN-Bus controller ... block Tenth IDE hard disk/CD-ROM interface 0 = /dev/hds Master: whole disk (or CD-ROM) 64 = /dev/hdt Slave: whole disk (or CD-ROM) Partitions are handled the same way as for the first interface (see major number 3). 92 char Reserved for ith Kommunikationstechnik MIC ISDN card block PPDD encrypted disk driver 0 = /dev/ppdd0 First encrypted disk 1 = /dev/ppdd1 Second encrypted disk ... Partitions are handled in the same way as for IDE disks (see major number 3) except that the limit on partitions is 15. 93 char IBM Smart Capture Card frame grabber {2.6} 0 = /dev/iscc0 First Smart Capture Card 1 = /dev/iscc1 Second Smart Capture Card ... 128 = /dev/isccctl0 First Smart Capture Card control 129 = /dev/isccctl1 Second Smart Capture Card control ... block NAND Flash Translation Layer filesystem 0 = /dev/nftla First NFTL layer 16 = /dev/nftlb Second NFTL layer ... 240 = /dev/nftlp 16th NTFL layer 94 char miroVIDEO DC10/30 capture/playback device {2.6} 0 = /dev/dcxx0 First capture card 1 = /dev/dcxx1 Second capture card ... 95 char IP filter 0 = /dev/ipl Filter control device/log file 1 = /dev/ipnat NAT control device/log file 2 = /dev/ipstate State information log file 3 = /dev/ipauth Authentication control device/log file block IBM S/390 DASD block storage 0 = /dev/dasd0 First DASD device, major 1 = /dev/dasd0a First DASD device, block 1 2 = /dev/dasd0b First DASD device, block 2 3 = /dev/dasd0c First DASD device, block 3 4 = /dev/dasd1 Second DASD device, major 5 = /dev/dasd1a Second DASD device, block 1 6 = /dev/dasd1b Second DASD device, block 2 7 = /dev/dasd1c Second DASD device, block 3 ... 96 char Parallel port ATAPI tape devices 0 = /dev/pt0 First parallel port ATAPI tape 1 = /dev/pt1 Second parallel port ATAPI tape ... 128 = /dev/npt0 First p.p. ATAPI tape, no rewind 129 = /dev/npt1 Second p.p. ATAPI tape, no rewind ... block IBM S/390 VM/ESA minidisk 0 = /dev/msd0 First VM/ESA minidisk 1 = /dev/msd1 Second VM/ESA minidisk ... 97 char Parallel port generic ATAPI interface 0 = /dev/pg0 First parallel port ATAPI device 1 = /dev/pg1 Second parallel port ATAPI device 2 = /dev/pg2 Third parallel port ATAPI device 3 = /dev/pg3 Fourth parallel port ATAPI device These devices support the same API as the generic SCSI devices. block Packet writing for CD/DVD devices 0 = /dev/pktcdvd0 First packet-writing module 1 = /dev/pktcdvd1 Second packet-writing module ... 98 char Control and Measurement Device (comedi) 0 = /dev/comedi0 First comedi device 1 = /dev/comedi1 Second comedi device ... See http://stm.lbl.gov/comedi or http://www.llp.fu-berlin.de/. block User-mode virtual block device 0 = /dev/ubd0 First user-mode block device 1 = /dev/ubd1 Second user-mode block device ... This device is used by the user-mode virtual kernel port. 99 char Raw parallel ports 0 = /dev/parport0 First parallel port 1 = /dev/parport1 Second parallel port ... block JavaStation flash disk 0 = /dev/jsfd JavaStation flash disk 100 char Telephony for Linux 0 = /dev/phone0 First telephony device 1 = /dev/phone1 Second telephony device ... 101 char Motorola DSP 56xxx board 0 = /dev/mdspstat Status information 1 = /dev/mdsp1 First DSP board I/O controls ... 16 = /dev/mdsp16 16th DSP board I/O controls block AMI HyperDisk RAID controller 0 = /dev/amiraid/ar0 First array whole disk 16 = /dev/amiraid/ar1 Second array whole disk ... 240 = /dev/amiraid/ar15 16th array whole disk For each device, partitions are added as: 0 = /dev/amiraid/ar? Whole disk 1 = /dev/amiraid/ar?p1 First partition 2 = /dev/amiraid/ar?p2 Second partition ... 15 = /dev/amiraid/ar?p15 15th partition 102 char Philips SAA5249 Teletext signal decoder {2.6} 0 = /dev/tlk0 First Teletext decoder 1 = /dev/tlk1 Second Teletext decoder 2 = /dev/tlk2 Third Teletext decoder 3 = /dev/tlk3 Fourth Teletext decoder 103 char Arla network file system 0 = /dev/xfs0 Arla XFS Arla is a free clone of the Andrew File System, AFS. Any resemblance with the Swedish milk producer is coincidental. For more information about the project, write to or subscribe to the arla announce mailing list by sending a mail to . block Audit device 0 = /dev/audit Audit device 104 char Flash BIOS support block Compaq Next Generation Drive Array, first controller 0 = /dev/cciss/c0d0 First logical drive, whole disk 16 = /dev/cciss/c0d1 Second logical drive, whole disk ... 240 = /dev/cciss/c0d15 16th logical drive, whole disk Partitions are handled the same way as for Mylex DAC960 (see major number 48) except that the limit on partitions is 15. 105 char Comtrol VS-1000 serial controller 0 = /dev/ttyV0 First VS-1000 port 1 = /dev/ttyV1 Second VS-1000 port ... block Compaq Next Generation Drive Array, second controller 0 = /dev/cciss/c1d0 First logical drive, whole disk 16 = /dev/cciss/c1d1 Second logical drive, whole disk ... 240 = /dev/cciss/c1d15 16th logical drive, whole disk Partitions are handled the same way as for Mylex DAC960 (see major number 48) except that the limit on partitions is 15. 106 char Comtrol VS-1000 serial controller - alternate devices 0 = /dev/cuv0 First VS-1000 port 1 = /dev/cuv1 Second VS-1000 port ... block Compaq Next Generation Drive Array, third controller 0 = /dev/cciss/c2d0 First logical drive, whole disk 16 = /dev/cciss/c2d1 Second logical drive, whole disk ... 240 = /dev/cciss/c2d15 16th logical drive, whole disk Partitions are handled the same way as for Mylex DAC960 (see major number 48) except that the limit on partitions is 15. 107 char 3Dfx Voodoo Graphics device 0 = /dev/3dfx Primary 3Dfx graphics device block Compaq Next Generation Drive Array, fourth controller 0 = /dev/cciss/c3d0 First logical drive, whole disk 16 = /dev/cciss/c3d1 Second logical drive, whole disk ... 240 = /dev/cciss/c3d15 16th logical drive, whole disk Partitions are handled the same way as for Mylex DAC960 (see major number 48) except that the limit on partitions is 15. 108 char Device independent PPP interface 0 = /dev/ppp Device independent PPP interface block Compaq Next Generation Drive Array, fifth controller 0 = /dev/cciss/c4d0 First logical drive, whole disk 16 = /dev/cciss/c4d1 Second logical drive, whole disk ... 240 = /dev/cciss/c4d15 16th logical drive, whole disk Partitions are handled the same way as for Mylex DAC960 (see major number 48) except that the limit on partitions is 15. 109 char Reserved for logical volume manager block Compaq Next Generation Drive Array, sixth controller 0 = /dev/cciss/c5d0 First logical drive, whole disk 16 = /dev/cciss/c5d1 Second logical drive, whole disk ... 240 = /dev/cciss/c5d15 16th logical drive, whole disk Partitions are handled the same way as for Mylex DAC960 (see major number 48) except that the limit on partitions is 15. 110 char miroMEDIA Surround board 0 = /dev/srnd0 First miroMEDIA Surround board 1 = /dev/srnd1 Second miroMEDIA Surround board ... block Compaq Next Generation Drive Array, seventh controller 0 = /dev/cciss/c6d0 First logical drive, whole disk 16 = /dev/cciss/c6d1 Second logical drive, whole disk ... 240 = /dev/cciss/c6d15 16th logical drive, whole disk Partitions are handled the same way as for Mylex DAC960 (see major number 48) except that the limit on partitions is 15. 111 char Philips SAA7146-based audio/video card {2.6} 0 = /dev/av0 First A/V card 1 = /dev/av1 Second A/V card ... block Compaq Next Generation Drive Array, eigth controller 0 = /dev/cciss/c7d0 First logical drive, whole disk 16 = /dev/cciss/c7d1 Second logical drive, whole disk ... 240 = /dev/cciss/c7d15 16th logical drive, whole disk Partitions are handled the same way as for Mylex DAC960 (see major number 48) except that the limit on partitions is 15. 112 char ISI serial card 0 = /dev/ttyM0 First ISI port 1 = /dev/ttyM1 Second ISI port ... There is currently a device-naming conflict between these and PAM multimodems (major 78). 113 char ISI serial card - alternate devices 0 = /dev/cum0 Callout device for ttyM0 1 = /dev/cum1 Callout device for ttyM1 ... 114 char Picture Elements ISE board 0 = /dev/ise0 First ISE board 1 = /dev/ise1 Second ISE board ... 128 = /dev/isex0 Control node for first ISE board 129 = /dev/isex1 Control node for second ISE board ... The ISE board is an embedded computer, optimized for image processing. The /dev/iseN nodes are the general I/O access to the board, the /dev/isex0 nodes command nodes used to control the board. 115 char Console driver speaker 0 = /dev/speaker Speaker device file Plays music using IBM BASIC style strings. 116 char Advanced Linux Sound Driver (ALSA) 117 char COSA/SRP synchronous serial card 0 = /dev/cosa0c0 1st board, 1st channel 1 = /dev/cosa0c1 1st board, 2nd channel ... 16 = /dev/cosa1c0 2nd board, 1st channel 17 = /dev/cosa1c1 2nd board, 2nd channel ... 118 char Solidum ??? 0 = /dev/solnp0 1 = /dev/solnp1 ... 128 = /dev/solnpctl0 129 = /dev/solnpctl1 ... 119 char VMware virtual network control 0 = /dev/vnet0 1st virtual network 1 = /dev/vnet1 2nd virtual network ... 120-127 LOCAL/EXPERIMENTAL USE 128-135 char Unix98 PTY masters These devices should not have corresponding device nodes; instead they should be accessed through the /dev/ptmx cloning interface. 136-143 char Unix98 PTY slaves 0 = /dev/pts/0 First Unix98 pseudo-TTY 1 = /dev/pts/1 Second Unix98 pesudo-TTY ... These device nodes are automatically generated with the proper permissions and modes by mounting the devpts filesystem onto /dev/pts with the appropriate mount options (distribution dependent, however, on *most* distributions the appropriate options are "mode=0620,gid=".) 144 char Encapsulated PPP 0 = /dev/pppox0 First PPP over Ethernet ... 63 = /dev/pppox63 64th PPP over Ethernet This is primarily used for ADSL. The SST 5136-DN DeviceNet interface driver has been relocated to major 183 due to an unfortunate conflict. 145 char SAM9407-based soundcard 0 = /dev/sam0_mixer 1 = /dev/sam0_sequencer 2 = /dev/sam0_midi00 3 = /dev/sam0_dsp 4 = /dev/sam0_audio 6 = /dev/sam0_sndstat 18 = /dev/sam0_midi01 34 = /dev/sam0_midi02 50 = /dev/sam0_midi03 64 = /dev/sam1_mixer ... 128 = /dev/sam2_mixer ... 192 = /dev/sam3_mixer ... Device functions match OSS, but offer a number of addons, which are sam9407 specific. OSS can be operated simultaneously, taking care of the codec. 146 char SYSTRAM SCRAMNet mirrored-memory network 0 = /dev/scramnet0 First SCRAMNet device 1 = /dev/scramnet1 Second SCRAMNet device ... 147 char Aueral Semiconductor Vortex Audio device 0 = /dev/aureal0 First Aureal Vortex 1 = /dev/aureal1 Second Aureal Vortex ... 148 char Technology Concepts serial card 0 = /dev/ttyT0 First TCL port 1 = /dev/ttyT1 Second TCL port ... 149 char Technology Concepts serial card - alternate devices 0 = /dev/cut0 Callout device for ttyT0 1 = /dev/cut0 Callout device for ttyT1 ... 150 char Real-Time Linux FIFOs 0 = /dev/rtf0 First RTLinux FIFO 1 = /dev/rtf1 Second RTLinux FIFO ... 151 char DPT I2O SmartRaid V controller 0 = /dev/dpti0 First DPT I2O adapter 1 = /dev/dpti1 Second DPT I2O adapter ... 154 char Specialix RIO serial card 0 = /dev/ttySR0 First RIO port ... 255 = /dev/ttySR255 256th RIO port 155 char Specialix RIO serial card - alternate devices 0 = /dev/cusr0 Callout device for ttySR0 ... 255 = /dev/cusr255 Callout device for ttySR255 156 char Specialix RIO serial card 0 = /dev/ttySR256 257th RIO port ... 255 = /dev/ttySR511 512th RIO port 157 char Specialix RIO serial card - alternate devices 0 = /dev/cusr256 Callout device for ttySR256 ... 255 = /dev/cusr511 Callout device for ttySR511 158 char Dialogic GammaLink fax driver 0 = /dev/gfax0 GammaLink channel 0 1 = /dev/gfax1 GammaLink channel 1 ... 159 RESERVED 160 char General Purpose Instrument Bus (GPIB) 0 = /dev/gpib0 First GPIB bus 1 = /dev/gpib1 Second GPIB bus ... 161 char IrCOMM devices (IrDA serial/parallel emulation) 0 = /dev/ircomm0 First IrCOMM device 1 = /dev/ircomm1 Second IrCOMM device ... 16 = /dev/irlpt0 First IrLPT device 17 = /dev/irlpt1 Second IrLPT device ... 162 char Raw block device interface 0 = /dev/raw Raw I/O control device 1 = /dev/raw1 First raw I/O device 2 = /dev/raw2 Second raw I/O device ... 163 char Radio Tech BIM-XXX-RS232 radio modem 0 = /dev/bimrt0 First BIM radio modem 1 = /dev/bimrt1 Second BIM radio modem ... 164 char Chase Research AT/PCI-Fast serial card 0 = /dev/ttyCH0 AT/PCI-Fast board 0, port 0 ... 15 = /dev/ttyCH15 AT/PCI-Fast board 0, port 15 16 = /dev/ttyCH16 AT/PCI-Fast board 1, port 0 ... 31 = /dev/ttyCH31 AT/PCI-Fast board 1, port 15 32 = /dev/ttyCH32 AT/PCI-Fast board 2, port 0 ... 47 = /dev/ttyCH47 AT/PCI-Fast board 2, port 15 48 = /dev/ttyCH48 AT/PCI-Fast board 3, port 0 ... 63 = /dev/ttyCH63 AT/PCI-Fast board 3, port 15 165 char Chase Research AT/PCI-Fast serial card - alternate devices 0 = /dev/cuch0 Callout device for ttyCH0 ... 63 = /dev/cuch63 Callout device for ttyCH63 166 char ACM USB modems 0 = /dev/ttyACM0 First ACM modem 1 = /dev/ttyACM1 Second ACM modem ... 167 char ACM USB modems - alternate devices 0 = /dev/cuacm0 Callout device for ttyACM0 1 = /dev/cuacm1 Callout device for ttyACM1 ... 168 char Eracom CSA7000 PCI encryption adaptor 0 = /dev/ecsa0 First CSA7000 1 = /dev/ecsa1 Second CSA7000 ... 169 char Eracom CSA8000 PCI encryption adaptor 0 = /dev/ecsa8-0 First CSA8000 1 = /dev/ecsa8-1 Second CSA8000 ... 170 char AMI MegaRAC remote access controller 0 = /dev/megarac0 First MegaRAC card 1 = /dev/megarac1 Second MegaRAC card ... 171 char Reserved for IEEE 1394 (Firewire) 172 char Moxa Intellio serial card 0 = /dev/ttyMX0 First Moxa port 1 = /dev/ttyMX1 Second Moxa port ... 127 = /dev/ttyMX127 128th Moxa port 128 = /dev/moxactl Moxa control port 173 char Moxa Intellio serial card - alternate devices 0 = /dev/cumx0 Callout device for ttyMX0 1 = /dev/cumx1 Callout device for ttyMX1 ... 127 = /dev/cumx127 Callout device for ttyMX127 174 char SmartIO serial card 0 = /dev/ttySI0 First SmartIO port 1 = /dev/ttySI1 Second SmartIO port ... 175 char SmartIO serial card - alternate devices 0 = /dev/cusi0 Callout device for ttySI0 1 = /dev/cusi1 Callout device for ttySI1 ... 176 char nCipher nFast PCI crypto accelerator 0 = /dev/nfastpci0 First nFast PCI device 1 = /dev/nfastpci1 First nFast PCI device ... 177 char TI PCILynx memory spaces 0 = /dev/pcilynx/aux0 AUX space of first PCILynx card ... 15 = /dev/pcilynx/aux15 AUX space of 16th PCILynx card 16 = /dev/pcilynx/rom0 ROM space of first PCILynx card ... 31 = /dev/pcilynx/rom15 ROM space of 16th PCILynx card 32 = /dev/pcilynx/ram0 RAM space of first PCILynx card ... 47 = /dev/pcilynx/ram15 RAM space of 16th PCILynx card 178 char Giganet cLAN1xxx virtual interface adapter 0 = /dev/clanvi0 First cLAN adapter 1 = /dev/clanvi1 Second cLAN adapter ... 179 char CCube DVXChip-based PCI products 0 = /dev/dvxirq0 First DVX device 1 = /dev/dvxirq1 Second DVX device ... 180 char USB devices 0 = /dev/usb/lp0 First USB printer ... 15 = /dev/usb/lp15 16th USB printer 16 = /dev/usb/mouse0 First USB mouse ... 31 = /dev/usb/mouse15 16th USB mouse 32 = /dev/usb/ez0 First USB firmware loader ... 47 = /dev/usb/ez15 16th USB firmware loader 48 = /dev/usb/scanner0 First USB scanner ... 63 = /dev/usb/scanner15 16th USB scanner 64 = /dev/usb/rio500 Diamond Rio 500 181 char Conrad Electronic parallel port radio clocks 0 = /dev/pcfclock0 First Conrad radio clock 1 = /dev/pcfclock1 Second Conrad radio clock ... 182 char Picture Elements THR2 binarizer 0 = /dev/pethr0 First THR2 board 1 = /dev/pethr1 Second THR2 board ... 183 char SST 5136-DN DeviceNet interface 0 = /dev/ss5136dn0 First DeviceNet interface 1 = /dev/ss5136dn1 Second DeviceNet interface ... This device used to be assigned to major number 144. It had to be moved due to an unfortunate conflict. 184 char Picture Elements' video simulator/sender 0 = /dev/pevss0 First sender board 1 = /dev/pevss1 Second sender board ... 185 char InterMezzo high availability file system 0 = /dev/intermezzo0 First cache manager 1 = /dev/intermezzo1 Second cache manager ... See http://www.inter-mezzo.org/ for more information. 186 char Object-based storage control device 0 = /dev/obd0 First obd control device 1 = /dev/obd1 Second obd control device ... See ftp://ftp.lustre.org/pub/obd for code and information. 187 char DESkey hardware encryption device 0 = /dev/deskey0 First DES key 1 = /dev/deskey1 Second DES key ... 188 char USB serial converters 0 = /dev/ttyUSB0 First USB serial converter 1 = /dev/ttyUSB1 Second USB serial converter ... 189 char USB serial converters - alternate devices 0 = /dev/cuusb0 Callout device for ttyUSB0 1 = /dev/cuusb1 Callout device for ttyUSB1 ... 190 char Kansas City tracker/tuner card 0 = /dev/kctt0 First KCT/T card 1 = /dev/kctt1 Second KCT/T card ... 191 char Reserved for PCMCIA 192 char Kernel profiling interface 0 = /dev/profile Profiling control device 1 = /dev/profile0 Profiling device for CPU 0 2 = /dev/profile1 Profiling device for CPU 1 ... 193 char Kernel event-tracing interface 0 = /dev/trace Tracing control device 1 = /dev/trace0 Tracing device for CPU 0 2 = /dev/trace1 Tracing device for CPU 1 ... 194 char linVideoStreams (LINVS) 0 = /dev/mvideo/status0 Video compression status 1 = /dev/mvideo/stream0 Video stream 2 = /dev/mvideo/frame0 Single compressed frame 3 = /dev/mvideo/rawframe0 Raw uncompressed frame 4 = /dev/mvideo/codec0 Direct codec access 5 = /dev/mvideo/video4linux0 Video4Linux compatibility 16 = /dev/mvideo/status1 Second device ... 32 = /dev/mvideo/status2 Third device ... ... 240 = /dev/mvideo/status15 16th device ... 195 char Nvidia graphics devices 0 = /dev/nvidia0 First Nvidia card 1 = /dev/nvidia1 Second Nvidia card ... 255 = /dev/nvidiactl Nvidia card control device 196-197 UNASSIGNED 198 char Total Impact TPMP2 quad coprocessor PCI card 0 = /dev/tpmp2/0 First card 1 = /dev/tpmp2/1 Second card ... 199 char Veritas volume manager (VxVM) volumes 0 = /dev/vx/rdsk/*/* First volume 1 = /dev/vx/rdsk/*/* Second volume ... block Veritas volume manager (VxVM) volumes 0 = /dev/vx/dsk/*/* First volume 1 = /dev/vx/dsk/*/* First volume ... The namespace in these directories is maintained by the user space VxVM software. 200 char Veritas VxVM configuration interface 0 = /dev/vx/config Configuration access node 1 = /dev/vx/trace Volume i/o trace access node 2 = /dev/vx/iod Volume i/o daemon access node 3 = /dev/vx/info Volume information access node 4 = /dev/vx/task Volume tasks access node 5 = /dev/vx/taskmon Volume tasks monitor daemon 201 char Veritas VxVM dynamic multipathing driver 0 = /dev/vx/rdmp/* First multipath device 1 = /dev/vx/rdmp/* Second multipath device ... block Veritas VxVM dynamic multipathing driver 0 = /dev/vx/dmp/* First multipath device 1 = /dev/vx/dmp/* Second multipath device ... The namespace in these directories is maintained by the user space VxVM software. 202 char CPU model-specific registers 0 = /dev/cpu/0/msr MSRs on CPU 0 1 = /dev/cpu/1/msr MSRs on CPU 1 ... 203 char CPU CPUID information 0 = /dev/cpu/0/cpuid CPUID on CPU 0 1 = /dev/cpu/1/cpuid CPUID on CPU 1 ... 204 char Low-density serial ports 0 = /dev/ttyLU0 LinkUp Systems L72xx UART - port 0 1 = /dev/ttyLU1 LinkUp Systems L72xx UART - port 1 2 = /dev/ttyLU2 LinkUp Systems L72xx UART - port 2 3 = /dev/ttyLU3 LinkUp Systems L72xx UART - port 3 4 = /dev/ttyFB0 Intel Footbridge (ARM) 5 = /dev/ttySA0 StrongARM builtin serial port 0 6 = /dev/ttySA1 StrongARM builtin serial port 1 7 = /dev/ttySA2 StrongARM builtin serial port 2 8 = /dev/ttySC0 SCI serial port (SuperH) - port 0 9 = /dev/ttySC1 SCI serial port (SuperH) - port 1 10 = /dev/ttySC2 SCI serial port (SuperH) - port 2 11 = /dev/ttySC3 SCI serial port (SuperH) - port 3 12 = /dev/ttyFW0 Firmware console - port 0 13 = /dev/ttyFW1 Firmware console - port 1 14 = /dev/ttyFW2 Firmware console - port 2 15 = /dev/ttyFW3 Firmware console - port 3 16 = /dev/ttyAM0 ARM "AMBA" serial port 0 ... 31 = /dev/ttyAM15 ARM "AMBA" serial port 15 205 char Low-density serial ports (alternate device) 0 = /dev/culu0 Callout device for ttyLU0 1 = /dev/culu1 Callout device for ttyLU1 2 = /dev/culu2 Callout device for ttyLU2 3 = /dev/culu3 Callout device for ttyLU3 4 = /dev/cufb0 Callout device for ttyFB0 5 = /dev/cusa0 Callout device for ttySA0 6 = /dev/cusa1 Callout device for ttySA1 7 = /dev/cusa2 Callout device for ttySA2 8 = /dev/cusc0 Callout device for ttySC0 9 = /dev/cusc1 Callout device for ttySC1 10 = /dev/cusc2 Callout device for ttySC2 11 = /dev/cusc3 Callout device for ttySC3 12 = /dev/cufw0 Callout device for ttyFW0 13 = /dev/cufw1 Callout device for ttyFW1 14 = /dev/cufw2 Callout device for ttyFW2 15 = /dev/cufw3 Callout device for ttyFW3 16 = /dev/cuam0 Callout device for ttyAM0 ... 31 = /dev/cuam15 Callout device for ttyAM15 206 char OnStream SC-x0 tape devices 0 = /dev/osst0 First OnStream SCSI tape, mode 0 1 = /dev/osst1 Second OnStream SCSI tape, mode 0 ... 32 = /dev/osst0l First OnStream SCSI tape, mode 1 33 = /dev/osst1l Second OnStream SCSI tape, mode 1 ... 64 = /dev/osst0m First OnStream SCSI tape, mode 2 65 = /dev/osst1m Second OnStream SCSI tape, mode 2 ... 96 = /dev/osst0a First OnStream SCSI tape, mode 3 97 = /dev/osst1a Second OnStream SCSI tape, mode 3 ... 128 = /dev/nosst0 No rewind version of /dev/osst0 129 = /dev/nosst1 No rewind version of /dev/osst1 ... 160 = /dev/nosst0l No rewind version of /dev/osst0l 161 = /dev/nosst1l No rewind version of /dev/osst1l ... 192 = /dev/nosst0m No rewind version of /dev/osst0m 193 = /dev/nosst1m No rewind version of /dev/osst1m ... 224 = /dev/nosst0a No rewind version of /dev/osst0a 225 = /dev/nosst1a No rewind version of /dev/osst1a ... The OnStream SC-x0 SCSI tapes do not support the standard SCSI SASD command set and therefore need their own driver "osst". Note that the IDE, USB (and maybe ParPort) versions may be driven via ide-scsi or usb-storage SCSI emulation and this osst device and driver as well. The ADR-x0 drives are QIC-157 compliant and don't need osst. 207 char Compaq ProLiant health feature indicate 0 = /dev/cpqhealth/cpqw Redirector interface 1 = /dev/cpqhealth/crom EISA CROM 2 = /dev/cpqhealth/cdt Data Table 3 = /dev/cpqhealth/cevt Event Log 4 = /dev/cpqhealth/casr Automatic Server Recovery 5 = /dev/cpqhealth/cecc ECC Memory 6 = /dev/cpqhealth/cmca Machine Check Architecture 7 = /dev/cpqhealth/ccsm Deprecated CDT 8 = /dev/cpqhealth/cnmi NMI Handling 9 = /dev/cpqhealth/css Sideshow Management 10 = /dev/cpqhealth/cram CMOS interface 11 = /dev/cpqhealth/cpci PCI IRQ interface 208 char User space serial ports 0 = /dev/ttyU0 First user space serial port 1 = /dev/ttyU1 Second user space serial port ... 209 char User space serial ports (alternate devices) 0 = /dev/cuu0 Callout device for ttyU0 1 = /dev/cuu1 Callout device for ttyU1 ... 210 char SBE, Inc. sync/async serial card 0 = /dev/sbei/wxcfg0 Configuration device for board 0 1 = /dev/sbei/dld0 Download device for board 0 2 = /dev/sbei/wan00 WAN device, port 0, board 0 3 = /dev/sbei/wan01 WAN device, port 1, board 0 4 = /dev/sbei/wan02 WAN device, port 2, board 0 5 = /dev/sbei/wan03 WAN device, port 3, board 0 6 = /dev/sbei/wanc00 WAN clone device, port 0, board 0 7 = /dev/sbei/wanc01 WAN clone device, port 1, board 0 8 = /dev/sbei/wanc02 WAN clone device, port 2, board 0 9 = /dev/sbei/wanc03 WAN clone device, port 3, board 0 10 = /dev/sbei/wxcfg1 Configuration device for board 1 11 = /dev/sbei/dld1 Download device for board 1 12 = /dev/sbei/wan10 WAN device, port 0, board 1 13 = /dev/sbei/wan11 WAN device, port 1, board 1 14 = /dev/sbei/wan12 WAN device, port 2, board 1 15 = /dev/sbei/wan13 WAN device, port 3, board 1 16 = /dev/sbei/wanc10 WAN clone device, port 0, board 1 17 = /dev/sbei/wanc11 WAN clone device, port 1, board 1 18 = /dev/sbei/wanc12 WAN clone device, port 2, board 1 19 = /dev/sbei/wanc13 WAN clone device, port 3, board 1 ... Yes, each board is really spaced 10 (decimal) apart. 211 char Addinum CPCI1500 digital I/O card 0 = /dev/addinum/cpci1500/0 First CPCI1500 card 1 = /dev/addinum/cpci1500/1 Second CPCI1500 card ... 216 char USB BlueTooth devices 0 = /dev/ttyUB0 First USB BlueTooth device 1 = /dev/ttyUB1 Second USB BlueTooth device ... 217 char USB BlueTooth devices (alternate devices) 0 = /dev/cuub0 Callout device for ttyUB0 1 = /dev/cuub1 Callout device for ttyUB1 ... 218 char The Logical Company bus Unibus/Qbus adapters 0 = /dev/logicalco/bci/0 First bus adapter 1 = /dev/logicalco/bci/1 First bus adapter ... 219 char The Logical Company DCI-1300 digital I/O card 0 = /dev/logicalco/dci1300/0 First DCI-1300 card 1 = /dev/logicalco/dci1300/1 Second DCI-1300 card ... 220 char Myricom Myrinet "GM" board 0 = /dev/myricom/gm0 First Myrinet GM board 1 = /dev/myricom/gmp0 First board "root access" 2 = /dev/myricom/gm1 Second Myrinet GM board 3 = /dev/myricom/gmp1 Second board "root access" ... 221 char VME bus 0 = /dev/bus/vme/m0 First master image 1 = /dev/bus/vme/m1 Second master image 2 = /dev/bus/vme/m2 Third master image 3 = /dev/bus/vme/m3 Fourth master image 4 = /dev/bus/vme/s0 First slave image 5 = /dev/bus/vme/s1 Second slave image 6 = /dev/bus/vme/s2 Third slave image 7 = /dev/bus/vme/s3 Fourth slave image 8 = /dev/bus/vme/ctl Control It is expected that all VME bus drivers will use the same interface. For interface documentation see http://www.vmelinux.org/. 224 char A2232 serial card 0 = /dev/ttyY0 First A2232 port 1 = /dev/ttyY1 Second A2232 port ... 225 char A2232 serial card (alternate devices) 0 = /dev/cuy0 Callout device for ttyY0 1 = /dev/cuy1 Callout device for ttyY1 ... 226-239 UNASSIGNED 240-254 LOCAL/EXPERIMENTAL USE 255 RESERVED This major is reserved to assist the expansion to a larger number space. No device nodes with this major should ever be created on the filesystem. **** ADDITIONAL /dev DIRECTORY ENTRIES This section details additional entries that should or may exist in the /dev directory. It is preferred that symbolic links use the same form (absolute or relative) as is indicated here. Links are classified as "hard" or "symbolic" depending on the preferred type of link; if possible, the indicated type of link should be used. Compulsory links These links should exist on all systems: /dev/fd /proc/self/fd symbolic File descriptors /dev/stdin fd/0 symbolic stdin file descriptor /dev/stdout fd/1 symbolic stdout file descriptor /dev/stderr fd/2 symbolic stderr file descriptor /dev/nfsd socksys symbolic Required by iBCS-2 /dev/X0R null symbolic Required by iBCS-2 Note: /dev/X0R is --. Recommended links It is recommended that these links exist on all systems: /dev/core /proc/kcore symbolic Backward compatibility /dev/ramdisk ram0 symbolic Backward compatibility /dev/ftape qft0 symbolic Backward compatibility /dev/bttv0 video0 symbolic Backward compatibility /dev/radio radio0 symbolic Backward compatibility /dev/i2o* /dev/i2o/* symbolic Backward compatibility /dev/scd? sr? hard Alternate SCSI CD-ROM name Locally defined links The following links may be established locally to conform to the configuration of the system. This is merely a tabulation of existing practice, and does not constitute a recommendation. However, if they exist, they should have the following uses. /dev/mouse mouse port symbolic Current mouse device /dev/tape tape device symbolic Current tape device /dev/cdrom CD-ROM device symbolic Current CD-ROM device /dev/cdwriter CD-writer symbolic Current CD-writer device /dev/scanner scanner symbolic Current scanner device /dev/modem modem port symbolic Current dialout device /dev/root root device symbolic Current root filesystem /dev/swap swap device symbolic Current swap device /dev/modem should not be used for a modem which supports dialin as well as dialout, as it tends to cause lock file problems. If it exists, /dev/modem should point to the appropriate primary TTY device (the use of the alternate callout devices is deprecated). For SCSI devices, /dev/tape and /dev/cdrom should point to the ``cooked'' devices (/dev/st* and /dev/sr*, respectively), whereas /dev/cdwriter and /dev/scanner should point to the appropriate generic SCSI devices (/dev/sg*). /dev/mouse may point to a primary serial TTY device, a hardware mouse device, or a socket for a mouse driver program (e.g. /dev/gpmdata). Sockets and pipes Non-transient sockets and named pipes may exist in /dev. Common entries are: /dev/printer socket lpd local socket /dev/log socket syslog local socket /dev/gpmdata socket gpm mouse multiplexer Mount points The following names are reserved for mounting special filesystems under /dev. These special filesystems provide kernel interfaces that cannot be provided with standard device nodes. /dev/pts devpts PTY slave filesystem /dev/shm shmfs POSIX shared memory maintenance access **** TERMINAL DEVICES Terminal, or TTY devices are a special class of character devices. A terminal device is any device that could act as a controlling terminal for a session; this includes virtual consoles, serial ports, and pseudoterminals (PTYs). All terminal devices share a common set of capabilities known as line diciplines; these include the common terminal line dicipline as well as SLIP and PPP modes. All terminal devices are named similarly; this section explains the naming and use of the various types of TTYs. Note that the naming conventions include several historical warts; some of these are Linux-specific, some were inherited from other systems, and some reflect Linux outgrowing a borrowed convention. A hash mark (#) in a device name is used here to indicate a decimal number without leading zeroes. Virtual consoles and the console device Virtual consoles are full-screen terminal displays on the system video monitor. Virtual consoles are named /dev/tty#, with numbering starting at /dev/tty1; /dev/tty0 is the current virtual console. /dev/tty0 is the device that should be used to access the system video card on those architectures for which the frame buffer devices (/dev/fb*) are not applicable. Do not use /dev/console for this purpose. The console device, /dev/console, is the device to which system messages should be sent, and on which logins should be permitted in single-user mode. Starting with Linux 2.1.71, /dev/console is managed by the kernel; for previous versions it should be a symbolic link to either /dev/tty0, a specific virtual console such as /dev/tty1, or to a serial port primary (tty*, not cu*) device, depending on the configuration of the system. Serial ports Serial ports are RS-232 serial ports and any device which simulates one, either in hardware (such as internal modems) or in software (such as the ISDN driver.) Under Linux, each serial ports has two device names, the primary or callin device and the alternate or callout one. Each kind of device is indicated by a different letter. For any letter X, the names of the devices are /dev/ttyX# and /dev/cux#, respectively; for historical reasons, /dev/ttyS# and /dev/ttyC# correspond to /dev/cua# and /dev/cub#. In the future, it should be expected that multiple letters will be used; all letters will be upper case for the "tty" device (e.g. /dev/ttyDP#) and lower case for the "cu" device (e.g. /dev/cudp#). The names /dev/ttyQ# and /dev/cuq# are reserved for local use. The alternate devices provide for kernel-based exclusion and somewhat different defaults than the primary devices. Their main purpose is to allow the use of serial ports with programs with no inherent or broken support for serial ports. Their use is deprecated, and they may be removed from a future version of Linux. Arbitration of serial ports is provided by the use of lock files with the names /var/lock/LCK..ttyX#. The contents of the lock file should be the PID of the locking process as an ASCII number. It is common practice to install links such as /dev/modem which point to serial ports. In order to ensure proper locking in the presence of these links, it is recommended that software chase symlinks and lock all possible names; additionally, it is recommended that a lock file be installed with the corresponding alternate device. In order to avoid deadlocks, it is recommended that the locks are acquired in the following order, and released in the reverse: 1. The symbolic link name, if any (/var/lock/LCK..modem) 2. The "tty" name (/var/lock/LCK..ttyS2) 3. The alternate device name (/var/lock/LCK..cua2) In the case of nested symbolic links, the lock files should be installed in the order the symlinks are resolved. Under no circumstances should an application hold a lock while waiting for another to be released. In addition, applications which attempt to create lock files for the corresponding alternate device names should take into account the possibility of being used on a non-serial port TTY, for which no alternate device would exist. Pseudoterminals (PTYs) Pseudoterminals, or PTYs, are used to create login sessions or provide other capabilities requiring a TTY line dicipline (including SLIP or PPP capability) to arbitrary data-generation processes. Each PTY has a master side, named /dev/pty[p-za-e][0-9a-f], and a slave side, named /dev/tty[p-za-e][0-9a-f]. The kernel arbitrates the use of PTYs by allowing each master side to be opened only once. Once the master side has been opened, the corresponding slave device can be used in the same manner as any TTY device. The master and slave devices are connected by the kernel, generating the equivalent of a bidirectional pipe with TTY capabilities. Recent versions of the Linux kernels and GNU libc contain support for the System V/Unix98 naming scheme for PTYs, which assigns a common device, /dev/ptmx, to all the masters (opening it will automatically give you a previously unassigned PTY) and a subdirectory, /dev/pts, for the slaves; the slaves are named with decimal integers (/dev/pts/# in our notation). This removes the problem of exhausting the namespace and enables the kernel to automatically create the device nodes for the slaves on demand using the "devpts" filesystem.