Linux and parallel port IDE devices PARIDE-2.0.35 (c) 1997-8 Grant Guenther ************************************************************************* Special notes for the 2.0.35 version: (i) This is the paride from 2.1.107 retrofitted to work with 2.0.34. (ii) PARPORT is _not_ supported. If you obtain the PARPORT patches for 2.0 and try to use them, it might work. I have not tried it. (iii) There is no guarantee of any ongoing support or future development for this special retrofit. (iv) I have not built or tested PARIDE with SMP support in 2.0.35, use it at your own risk. ************************************************************************* 1. Introduction Owing to the simplicity and near universality of the parallel port interface to personal computers, many external devices such as portable hard-disk, CD-ROM, LS-120 and tape drives use the parallel port to connect to their host computer. While some devices (notably scanners) use ad-hoc methods to pass commands and data through the parallel port interface, most external devices are actually identical to an internal model, but with a parallel-port adapter chip added in. Some of the original parallel port adapters were little more than mechanisms for multiplexing a SCSI bus. (The Iomega PPA-3 adapter used in the ZIP drives is an example of this approach). Most current designs, however, take a different approach. The adapter chip reproduces a small ISA or IDE bus in the external device and the communication protocol provides operations for reading and writing device registers, as well as data block transfer functions. Sometimes, the device being addressed via the parallel cable is a standard SCSI controller like an NCR 5380. The "ditto" family of external tape drives use the ISA replicator to interface a floppy disk controller, which is then connected to a floppy-tape mechanism. The vast majority of external parallel port devices, however, are now based on standard IDE type devices, which require no intermediate controller. If one were to open up a parallel port CD-ROM drive, for instance, one would find a standard ATAPI CD-ROM drive, a power supply, and a single adapter that interconnected a standard PC parallel port cable and a standard IDE cable. It is usually possible to exchange the CD-ROM device with any other device using the IDE interface. The document describes the support in Linux for parallel port IDE devices. It does not cover parallel port SCSI devices, "ditto" tape drives or scanners. Many different devices are supported by the parallel port IDE subsystem, including: MicroSolutions backpack CD-ROM MicroSolutions backpack PD/CD MicroSolutions backpack hard-drives MicroSolutions backpack 8000t tape drive SyQuest EZ-135, EZ-230 & SparQ drives Avatar Shark Imation Superdisk LS-120 FreeCom Power CD Hewlett-Packard 5GB tape drive Hewlett-Packard 7100 and 7200 CD-RW drives as well as most of the clone and no-name products on the market. To support such a wide range of devices, PARIDE, the parallel port IDE subsystem, is actually structured in three parts. There is a base paride module which provides a registry and some common methods for accessing the parallel ports. The second component is a set of high-level drivers for each of the different type of supported device: pd IDE disk pcd ATAPI CD-ROM pf ATAPI disk pt ATAPI tape pg ATAPI generic (Currently, the pg driver is only used with CD-R drives). The high-level drivers function according to the relevant standards. The third component of PARIDE is a set of low-level protocol drivers for each of the parallel port IDE adapter chips. Thanks to the interest and encouragement of Linux users from many parts of the world, support is available for almost all known adapter protocols: aten ATEN EH-100 (HK) bpck Microsolutions backpack (US) comm DataStor (old-type) "commuter" adapter (TW) dstr DataStor EP-2000 (TW) epat Shuttle EPAT (UK) epia Shuttle EPIA (UK) fit2 FIT TD-2000 (US) fit3 FIT TD-3000 (US) frpw Freecom Power (DE) kbic KingByte KBIC-951A and KBIC-971A (TW) ktti KT Technology PHd adapter (SG) on20 OnSpec 90c20 (US) on26 OnSpec 90c26 (US) 2. Using the PARIDE subsystem While configuring the Linux kernel, you may choose either to build the PARIDE drivers into your kernel, or to build them as modules. In either case, you will need to select "Parallel port IDE device support" as well as at least one of the high-level drivers and at least one of the parallel port communication protocols. If you do not know what kind of parallel port adapter is used in your drive, you could begin by checking the file names and any text files on your DOS installation floppy. Alternatively, you can look at the markings on the adapter chip itself. That's usually sufficient to identify the correct device. You can actually select all the protocol modules, and allow the PARIDE subsystem to try them all for you. For the "brand-name" products listed above, here are the protocol and high-level drivers that you would use: Manufacturer Model Driver Protocol MicroSolutions CD-ROM pcd bpck MicroSolutions PD drive pf bpck MicroSolutions hard-drive pd bpck MicroSolutions 8000t tape pt bpck SyQuest EZ, SparQ pd epat Imation Superdisk pf epat Avatar Shark pd epat FreeCom CD-ROM pcd frpw Hewlett-Packard 5GB Tape pt epat Hewlett-Packard 7100/7200 pg epat 2.1 Configuring built-in drivers We recommend that you get to know how the drivers work and how to configure them as loadable modules, before attempting to compile a kernel with the drivers built-in. If you built all of your PARIDE support directly into your kernel, and you have just a single parallel port IDE device, your kernel should locate it automatically for you. If you have more than one device, you may need to give some command line options to your bootloader (eg: LILO), how to do that is beyond the scope of this document. The high-level drivers accept a number of command line parameters, all of which are documented in the source files in linux/drivers/block/paride. By default, each driver will automatically try all parallel ports it can find, and all protocol types that have been installed, until it finds a parallel port IDE adapter. Once it finds one, the probe stops. So, if you have more than one device, you will need to tell the drivers how to identify them. This requires specifying the port address, the protocol identification number and, for some devices, the drive's chain ID. While your system is booting, a number of messages are displayed on the console. Like all such messages, they can be reviewed with the 'dmesg' command. Among those messages will be some lines like: paride: bpck registered as protocol 0 paride: epat registered as protocol 1 The numbers will always be the same until you build a new kernel with different protocol selections. You should note these numbers as you will need them to identify the devices. If you happen to be using a MicroSolutions backpack device, you will also need to know the unit ID number for each drive. This is usually the last two digits of the drive's serial number (but read MicroSolutions' documentation about this). As an example, let's assume that you have a MicroSolutions PD/CD drive with unit ID number 36 connected to the parallel port at 0x378, a SyQuest EZ-135 connected to the chained port on the PD/CD drive and also an Imation Superdisk connected to port 0x278. You could give the following options on your boot command: pd.drive0=0x378,1 pf.drive0=0x278,1 pf.drive1=0x378,0,36 In the last option, pf.drive1 configures device /dev/pf1, the 0x378 is the parallel port base address, the 0 is the protocol registration number and 36 is the chain ID. This (2.0.34) version of PARIDE does not support chained devices on the same parallel port. 2.2 Loading and configuring PARIDE as modules It is much faster and simpler to get to understand the PARIDE drivers if you use them as loadable kernel modules. Note: using these drivers with the "kerneld" automatic module loading system is not recommended, and is not documented here. To use PARIDE, you must begin by insmod paride this loads a base module which provides a registry for the protocols, among other tasks. Then, load as many of the protocol modules as you think you might need. As you load each module, it will register the protocols that it supports, and print a log message to your kernel log file and your console. For example: # insmod epat paride: epat registered as protocol 0 # insmod kbic paride: k951 registered as protocol 1 paride: k971 registered as protocol 2 Finally, you can load high-level drivers for each kind of device that you have connected. By default, each driver will autoprobe for a single device, but you can support up to four similar devices by giving their individual co-ordinates when you load the driver. For example, if you had two no-name CD-ROM drives both using the KingByte KBIC-951A adapter, one on port 0x378 and the other on 0x3bc you could give the following command: # insmod pcd drive0=0x378,1 drive1=0x3bc,1 For most adapters, giving a port address and protocol number is sufficient, but check the source files in linux/drivers/block/paride for more information. (Hopefully someone will write some man pages one day !). As another example, here's what happens when PARPORT is installed, and a SyQuest EZ-135 is attached to port 0x378: # insmod paride paride: version 1.0 installed # insmod epat paride: epat registered as protocol 0 # insmod pd pd: pd version 1.0, major 45, cluster 64, nice 0 pda: Sharing parport1 at 0x378 pda: epat 1.0, Shuttle EPAT chip c3 at 0x378, mode 5 (EPP-32), delay 1 pda: SyQuest EZ135A, 262144 blocks [128M], (512/16/32), removable media pda: pda1 Note that the last line is the output from the generic partition table scanner - in this case it reports that it has found a disk with one partition. 2.3 Using a PARIDE device Once the drivers have been loaded, you can access PARIDE devices in the same way as their traditional counterparts. You will probably need to create the device "special files". Here is a simple script that you can cut to a file and execute: #!/bin/bash # # mkd -- a script to create the device special files for the PARIDE subsystem # function mkdev { mknod $1 $2 $3 $4 ; chmod 0660 $1 ; chown root:disk $1 } # function pd { D=$( printf \\$( printf "x%03x" $[ $1 + 97 ] ) ) mkdev pd$D b 45 $[ $1 * 16 ] for P in 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 do mkdev pd$D$P b 45 $[ $1 * 16 + $P ] done } # cd /dev # for u in 0 1 2 3 ; do pd $u ; done for u in 0 1 2 3 ; do mkdev pcd$u b 46 $u ; done for u in 0 1 2 3 ; do mkdev pf$u b 47 $u ; done for u in 0 1 2 3 ; do mkdev pt$u c 96 $u ; done for u in 0 1 2 3 ; do mkdev npt$u c 96 $[ $u + 128 ] ; done for u in 0 1 2 3 ; do mkdev pg$u c 97 $u ; done # # end of mkd With the device files and drivers in place, you can access PARIDE devices like any other Linux device. For example, to mount a CD-ROM in pcd0, use: mount /dev/pcd0 /cdrom If you have a fresh Avatar Shark cartridge, and the drive is pda, you might do something like: fdisk /dev/pda -- make a new partition table with partition 1 of type 83 mke2fs /dev/pda1 -- to build the file system mkdir /shark -- make a place to mount the disk mount /dev/pda1 /shark Devices like the Imation superdisk work in the same way, except that they do not have a partition table. For example to make a 120MB floppy that you could share with a DOS system: mkdosfs /dev/pf0 mount /dev/pf0 /mnt 2.4 Using the pg driver The pg driver can be used in conjunction with the cdrecord program to create CD-ROMs. For more information, and the required patches to cdrecord, please visit http://www.torque.net/parport/cdr.html . 3. Troubleshooting While a lot of testing has gone into these drivers to make them work as smoothly as possible, problems will arise. If you do have problems, please check all the obvious things first: does the drive work in DOS with the manufacturer's drivers ? If that doesn't yield any useful clues, then please make sure that only one drive is hooked to your system, and that no other device driver is using your parallel port (check in /proc/ioports). Then, load the appropriate drivers (you can load several protocol modules if you want) as in: # insmod paride # insmod epat # insmod bpck # insmod kbic ... # insmod pd verbose=1 (using the correct driver for the type of device you have, of course). The verbose=1 parameter will cause the drivers to log a trace of their activity as they attempt to locate your drive. Use 'dmesg' to capture a log of all the PARIDE messages (any messages beginning with paride:, a protocol module's name or a driver's name) and include that with your bug report. You can submit a bug report in one of two ways. Either send it directly to the author of the PARIDE suite, by e-mail to grant@torque.net, or join the linux-parport mailing list and post your report there. You can join the linux-parport mailing list by sending a mail message to linux-parport-request@torque.net with the single word subscribe in the body of the mail message (not in the subject line). Please be sure that your mail program is correctly set up when you do this, as the list manager is a robot that will subscribe you using the reply address in your mail headers. REMOVE any anti-spam gimmicks you may have in your mail headers, when sending mail to the list server. You might also find some useful information on the linux-parport web pages (although they are not always up to date) at http://www.torque.net/parport/